Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com (https://www.camaro5.com/forums/index.php)
-   Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons (https://www.camaro5.com/forums/forumdisplay.php?f=11)
-   -   TSP Headers and Gears (https://www.camaro5.com/forums/showthread.php?t=310801)

Forsberg112 08-02-2013 09:24 PM
TSP Headers and Gears
 
1 Attachment(s)
Went down to Colorado Springs today and met with the guys over at RMCR. Finished up the Posi Mod and 3.91 Gear installation. Two weeks ago, they installed my TSP Headers, did my tune and provided me my current set of numbers. I am very happy with the service and product these guys provided, very happy with the numbers too!!:headbang:

62nalide 08-02-2013 10:00 PM
What size headers? 2" or 1 7/8" ? And nice numbers!

Forsberg112 08-02-2013 10:51 PM
I got the 2" ones, fitment was pretty good as well. I am definitely happy with the numbers.

Nightmare2012 08-02-2013 11:18 PM
How are you liking the posi mod I've heard ppl complain about it on curves under load

Forsberg112 08-03-2013 12:45 AM
I have not had the ability to really put any load on it during corners at the moment. I can understand what people complain about in general though, I had a similar mod on my Silverado a while back and it was great in a straight line, but was not as effective in the corners as limited slip is.

Camarojt 08-03-2013 11:37 AM
Quote:
Originally Posted by Forsberg112 (Post 6851965)
I got the 2" ones, fitment was pretty good as well. I am definitely happy with the numbers.
When you say fitment was "pretty good" that leads me to think that there was a slight issue? Are they touching somewhere??

Forsberg112 08-03-2013 12:13 PM
It touched the steering shaft boot, but not the shaft itself, so I was not too concerned about it.

litle88 08-03-2013 12:51 PM
Good numbers! Congrats.

thahemp 08-03-2013 12:55 PM
Quote:
Originally Posted by Forsberg112 (Post 6852997)
It touched the steering shaft boot, but not the shaft itself, so I was not too concerned about it.
Mine is within 1/8" too. They're the 1 7/8" headers. A little closer than I would like, but it has caused me 0 problems. Those boots can take the heat no problem. Same with the back of the spark plug wires on the driver's side.

Pro Stock John 08-03-2013 02:37 PM
Congrats, what is the posi mod, adding more clutches?

Camarojt 08-03-2013 03:04 PM
Quote:
Originally Posted by Forsberg112 (Post 6852997)
It touched the steering shaft boot, but not the shaft itself, so I was not too concerned about it.
Cool, so no noise or vibration from just touching the boot right?

K32 Camaro 08-03-2013 03:40 PM
I have the 2" TSP's. It was touching the boot as well. I didn't want it that close so I dented it til it was about an 1/8th away. I hated doing it.. but I didn't want to melt the boot.

thahemp 08-03-2013 04:19 PM
Quote:
Originally Posted by K32 Camaro (Post 6853528)
I have the 2" TSP's. It was touching the boot as well. I didn't want it that close so I dented it til it was about an 1/8th away. I hated doing it.. but I didn't want to melt the boot.
It won't melt, and mine relaxed over time. It was touching when i installed them, but after a couple weeks i had some clearance.

Forsberg112 08-03-2013 05:22 PM
I have not heard any type of noise out of it and have had it for two weeks now. My boot has not done any melting either.

As for the Posi Mod, I am not sure what they fully did, but I do know they added clutches to it, I believe they mentioned two more.


All times are GMT -5. The time now is 11:01 PM.
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.