A northern sleeper - pictures up! - 56K warning!
Deliverer September 18, 2009
Step 1 Debadge the car, except for drilled badging. [Postponed until body work] Step 2 5 minute run time oil change to break in oil (Royal Purple) [Complete] Step 3 Full HP dyno run, X3 to seat rings correctly [Today] Step 4 engine and performance mods
Step 5 3M RockGuard film and graphics [Completed] Step 6 Custom dyno tune with all performance parts installed [Completed] Step 7 1800km round trip to complete break in, season brakes and datalog [Completed] Step 8 Change oil with Type 4 synthetic oil (Amsoil Dominator 15W50) [Completed] Step 9 Replace rear differential fluid [Completed] Step 10 Suspension and brake mods
Custom paint scheme [2010/11 timeframe] Some inside (build details) done before cleaning and graphics. Stainless steel (red!) brake lines http://www.kpcnet.ca/images/SS/001.JPG LT headers pic 1 http://www.kpcnet.ca/images/SS/006.JPG LT headers pic 2 http://www.kpcnet.ca/images/SS/009.JPG Exhaust pic 1 http://www.kpcnet.ca/images/SS/016.JPG Exhaust pic 2 http://www.kpcnet.ca/images/SS/017.JPG Supercharger on table http://www.kpcnet.ca/images/SS/025.JPG Supercharger placed on engine http://www.kpcnet.ca/images/SS/027.JPG Supercharger installed http://www.kpcnet.ca/images/SS/031.JPG CAI heat shield http://www.kpcnet.ca/images/SS/034.JPG CAI being installed http://www.kpcnet.ca/images/SS/035.JPG CAI installed pic 1 http://www.kpcnet.ca/images/SS/038.JPG CAI installed pic 2 http://www.kpcnet.ca/images/SS/039.JPG CAI installed pic 3 http://www.kpcnet.ca/images/SS/040.JPG Headers and racing wires http://www.kpcnet.ca/images/SS/041.JPG Supercharger from right side of car http://www.kpcnet.ca/images/SS/044.JPG Fabbing up catch can mount pic 1 http://www.kpcnet.ca/images/SS/045.JPG Fabbing up catch can mount pic 2 http://www.kpcnet.ca/images/SS/048.JPG Catch can mounted http://www.kpcnet.ca/images/SS/052.JPG Catch can installed http://www.kpcnet.ca/images/SS/055.JPG Early gauge install http://www.kpcnet.ca/images/SS/063.JPG - SK |
Yowza! Someone's got a big budget! I can't wait to see how this one pans out!
|
Updated, final plan and TPW.
- SK |
Ordered/Purchased most of the parts.
- SK |
wow...that's a big plan...can't wait to see it!!
|
Almost all parts purchased/paid for now. Everything is shipping to dealer to hold until the car arrives.
Now for some aftermarket electronics, DashDaq II and GPS Snitch. Maybe a VBOX mini or 3i 100hz system. - SK |
:thumbsup: can't wait to see it!
|
Sounds like a dream come true, no?
|
Quote:
|
Dymag dealer called to say they are not sure now if the wheels will fit for sure. :(
DashDaq II with GM codes purchased, waiting to head to the big city to buy GPS Snitch. - SK |
Changed the exhaust due to availability.
Cancelled the Dymag wheels as I don't want to be the test fit case from over 8000 miles away. Now looking for non-staggered wheels. Added upgraded spark plugs and wire set. - SK |
I R CAN HAS VIN!
2G1FT1EW9A9132212, hehe, it is on carfax and everything ... :happyanim: - SK |
Engine Mounts
Hey Solo...Sounds great! :thumbsup: I am in the middle of a engine build & swap for my new SS. MTI Racing has the polyurethane engine mounts.
http://www.mtiracing.com |
Yeah, but I called them and availability is not yet. After looking at some of the dyno vids I was completely convinced of the need for motor and transmission mounts.
- SK |
All times are GMT -5. The time now is 04:06 PM. |
Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.