few pics of rocket after he was waxed :D and a pic of my uncles 1972 chevelle and 1964 impala
got to drive the chevelle it was a blast:wub: totally want one now:thumbup:

My husband buffed & waxed my car, I worked on the interior. The color is amazing after it's done.

Looks great! Enjoy!

thank you :D

painted the fusebox cover and cut a piece of aluminum and double taped it up i really hope it holds may backlight it with red leds later on but thats a whole nother project
will post better pics eventually

19,000 miles everything still running stong
working on a new under the hood bowtie hopefully everything works out and it gets backlit with red leds been a long tedious process but still hopeful!

Where did you get your seats?

iggee.com you can call them or order them off ebay

Looking good

I have black bowties (billet) that I'll give you free. I had installed them, but I went with the SS emblems from Sparks instead. All you'll need is new double sided tape.

Let me know if you want them, I'll ship them free.

Here is what they looked like when I had them on my car (before I installed hertiage grille and SS emblems):

http://www.camarorsss.com/images/blackbowtiefront.jpg
http://www.camarorsss.com/images/blackbowtierear.jpg

thanks man

Thanks bro i pmed you :thumbup:

redid the under the hood bowtie 2day screwed it in waiting on red leds 2 come in to back light it
ordered a roto fab cai from juiced motorsports had an awesome price
getting in black bowties thanks to CAMARO2SSRS ^^

will update with pics when everything comes in

Thank you :chevy:

How close is the seat cover color to our VR cars? I have yet to go on this site to check them out.

its a lighter red . email them and request a sample. i thought it would be a closer match but its deffinatly works with the car.i actually get the most compliments on my interior deffinatly reccomend them. oh its very hand to understand them on the phone be prepared to ask them to repeat themselves alot hahah

I shipped your black bowties and I also included a vinyl set that I had laying around in case you wanted to keep the chrome section of the bowtie.

The metal set I shipped is a little different than the ones in the photo. They are all black and replace the stock bowties, including the chrome section. The set that was in the photo could not be removed without damaging them.

You should have them by Thursday!

:headbang:

Thanks so much ill figure out what 1s i like best when they get here
Thanks again

just installed the front black billet bowtie looks awesome will post picks up 2morrow after i finish the rear and installing my roto fab cai:thumbup:

Nice! I'm glad you could use them, better than sitting around in my garage gathering dust. Can't wait to see the pics!

Thanks so much i really appericate it:thumbup:

ROTO-FAB INTAKE JUST ARRIVED waiting for the engine to cool down a little then going to install :thumbup:

intake is installed airbox gave me a bit of a problem but solved that really quick could do it in less then half the time next time but wanted to take my time and make sure everything was right!:D looks awesome under the hood will update on how the butt dyno feels next time i drive it :headbang:

pic update
billet aluminum black bowtie looks awesome! :thumbup:
rotofab cai :wub:

pics of the front bowtie comeing soon

putting on the rear bowtie was a pain in the A** but well worth it :) my fingers are killing me tho :(

You can use an adhesive remover to get the goo off or a heatgun and "roll" it off.

How did you get the old emblem off, fishing line right?

used a hair dryer and floss haha and i used the heat and goo gone to get the adhesive off. i looked the install up online said 10min for each bowtie, front i did in 10min...rear 1 not even close haha

went to a car show 2night won another trophy:w00t: working on under the hood bowtie led light.. almost done still doing some test fitting