Brake & Rotor job needed
Hello Everyone,
So today I was told by the service manager at my local chevy dealership that my car was going to need a brake job within the next 3,000 to 5,000 miles. Now with that said I now have questions before I make a decision concerning what to do. First a little background info for my car. I am the second owner and currently the car has 36,204 miles on it. I think the car has the original brake rotors and pads. I do drive fast but have not dragged/ raced the car and done any hard braking. So here are my questions. 1. If these are the original rotors is it better to replace them or can they be re-surfaced and reused? 2. What brake pads should I go with aftermarket or OEM? Again I do not race the car yet. lol 3. If I have to replace the rotors which rotors should I get. The drilled/slotted rotors are awesome but I'm trying to keep the costs as low as possible. (I'm a school teacher and I'm trying to get ready for the start of the school year. So that unfortunately is also taking some of my cash flow away!) 4. How much do you think brake pads, new rotors, and labor would cost me? If anyone could give me some advice I would greatly appreciate it.:dizzy: All the best, Roberta |
Depends on what you want. If you are looking to race later don't get cross drilled rotors since they tend to crack under high stress and heat. Get slotted and dimpled or just slotted rotors. Pads also depend on what you are trying to do. If its just street stockers are fine or go with a set of hawk pads. Ceramic are good for the street with less brake dust, hp are good for the street as well but more dust but have better bite.
Ask around for help in your area someone may up them on for free or a 12 pack lol If you wana make the long trip to the Palm Springs area I can install them for a few beers. |
I'm just over 96K on mine stock pads/rotors. I can tell you I just ordered some ceramic pads from Advanced Auto for about $60 to do the front and rear. I'm gonna chance not doing the rotors this time as they really aren't in too bad of shape. May regret it but saved a few hundred bucks for now. It seems like the last time I asked about getting some rotors turned they said they don't do it much any more. Maybe that was just here in my area though. Anyway, if they are not grooved or warped your probably ok. Not sure what labor would cost as I've never paid for it. Really if you have a jack and air tools you can do the job in around an hour (I hope!!!) without too much difficulty (I REALLY hope!!!) I've done other cars, just not my Camaro yet. I'm pretty certain any local shop is cheaper than the dealer though so you might ask around. Good luck!
|
Thanks for the feedback.
|
We have a great special going on for our Stillen Sport Rotors! Purchase any rotor and you will receive FREE Stillen Metal Matrix pads!
You have your choice of Cross Drilled, Slotted, Cross Drilled/Slotted and Hook Slotted! I will also give you a Camaro5 discount on the rotors! PM or Call me directly with any questions. Thanks JT |
Quote:
Best regards, Tyler 888-308-6007 |
My answers are in blue below.
Quote:
|
1. If these are the original rotors is it better to replace them or can they be re-surfaced and reused?
*After reading information I just decided to purchase new rotors and forgo the re-surface. 2. What brake pads should I go with aftermarket or OEM? Again I do not race the car yet. lol * I purchased aftermarket Hawk seemed the way to go cost a little more but not much. 3. If I have to replace the rotors which rotors should I get. The drilled/slotted rotors are awesome but I'm trying to keep the costs as low as possible. (I'm a school teacher and I'm trying to get ready for the start of the school year. So that unfortunately is also taking some of my cash flow away!) * I purchased slotted as I didnt see any gains from drilled rotors (with the exception of high priced racing rotors). The slotted looked as the best for stock / auto x on occasions. 4. How much do you think brake pads, new rotors, and labor would cost me? *Not sure on labor, but you could be looking at 600 or more if above OEM. Really if I were you I would PM some vendors and have them send you the prices. I just purchased new R1 rotors and hawk ceramic pads cost was $500.00 for everthing. The rotors were the premium slotted, so a little more cost to me. The items are for a 2LS (V6) Camaro so pricing will be a little more for a SS (V8). Plan on install this weekend and a 12 pac to someone. |
First thing to do is get a second opinion. Take it someplace that will give you a free estimate.
Second is if you are just street driving then stock is just fine for you and there is no reason to upgrade anything unless you want to. Third, unless your rotors are heavily grooved or cracked they should be ok and you shouldn't need to replace them. This is where a second opinion comes in handy. Replacing the pads is very simple on our cars and if you know anyone who is mechanically inclined they could do it for you relatively cheap. Like for the price of parts and a twelve pack. Let us know what happens and thank you for educating our future.:clap2: T. |
If i can help with DBA rotors and Hawk Pads let me know, i have some very good prices going on them right now.
|
Just wanted to say a very big thank you to everyone for their response's. I really do appreciate them all. It has really helped me narrow down my choices. I think I'm going with replacing the rotors with some slotted ones (not sure which brand just yet) as well as new Hawk HPS pads. We'll see what happens in the next couple of day's. :)
|
Quote:
|
Quote:
|
I'm in the same situation. Except I'm pushing 70k miles on mine.
Mine is primarily a DD, but in August I have a track day at Hallet. I have fluid ready to flysh(Amsoil DOT4). I will have my rotors examined. And I'm still deciding on pads. EBC Yellowstuff, Hawk HPS, or OE. |
All times are GMT -5. The time now is 06:53 AM. |
Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.