RacingBrake Lite Weight Front Big Brake Kit & Aluminum Caliper Kits Now @ APEX!!!
RacingBrake - Big Brake Kit, Front, w/ Rotors, 4 Piston Aluminum Calipers, SS Lines and Pads: $2265
RacingBrake - Aluminum Caliper Upgrade Kit: $1425.99 http://www.apex-speed.com/images/div.jpg http://www.apex-speed.com/images/det...5/2244-K-2.jpg RacingBrake - Big Brake Kit, Front, w/ Rotors, 4 Piston Aluminum Calipers, SS Lines and Pads: $2265 This is a complete brake kit for Camaro SS and a BBK for all V6 models from 2010 and up. This kit includes:
http://www.apex-speed.com/images/ven...k_calipers.jpg RacingBrake Calipers RacingBrake Calipers are made from forged 6061-T6 aluminum and precisely machined to every detail. Stock calipers - aluminum (Brembo) or cast iron (06-08 WRX) are mass-produced and are usually made through a casting or extrusion process which is not as dense and strong in structure as forging. - Caliper Body: Made of forged 6061-T6. Light weight at only 4.5lbs, these new RB4000 calipers are re-designed and built for the toughest brake jobs with extended service life before any rebuild is required. - Low Profile: Together with RB Center-Mount design two-piece rotors, you hardly even need to require a spacer to install the kit. - Piston Material: Made of stainless steel instead of aluminum commonly used by other caliper mfgrs which can substantially reduce the heat transfer (approx 1/10 of aluminum) from the pad to brake fluid. Pistons are vented to furtherreduce the heat contact area and improve air circulation thereby reducing more heat transfer. - Dust Seal: Our dust seal is of built-in type (instead of external boot type) uniquely designed to shield the dust and foreign material from contamination and will not rip - as commonly seen on boot type dust seals. http://www.apex-speed.com/images/ven..._dust_seal.jpg - Hardware: Brake pad pins and banjo connections were re-designed for easier brake line connection and brake pad replacement. - Surface Coating: Powder coating with most durable finish for lasting appeal. - Hardware: Most hardware is made of stainless steel for durable performance and appearance. - Never Get Lost Bleeder Cap: Newly designed with a retaining loop so you will never have to find it again and/replace the lost ones. (made of durable EPDM) http://www.apex-speed.com/images/ven...leeder_cap.jpg RacingBrake Rotors RacingBrake Rotors are made from forged 6061-T6 aluminum and precisely machined to every detail. Stock calipers - aluminum (Brembo) or cast iron (06-08 WRX) are mass-produced and are usually made through a casting or extrusion process which is not as dense and strong in structure as forging. RacingBrake Rotors are are directional (different for left and right sides), heat treated for added strength, and use RB's patented center mount design and convergent vane design, which increase airflow and makes the disc cooler. Electrodeposition Paint (EDP) is used to coat the aluminum hat, which is light weight and highly resistant to rust and corrosion. Hardware is a simple 2-piece component design (stud & nut) and is self locking to prevent the use of springs, glue, or clips. http://www.apex-speed.com/images/ven...k/2244-K-3.jpg Rotor Design: Our unique and patented rotor designs make our discs cooler and last longer.
RB ET Series Brake Pads From daily driver to dedicated tracking racing enthusiast, our ET-series brake pads provide a selection of various compounds that makes them easy to choose and use at an affordable cost. ET-Series Performance Street Compounds The ET Series compounds provide excellent modulation, consistent friction and torque output, and can be run from ambient temperature, even during cold winter mornings. ET300: Performance Street - Delivers braking performance beyond stock pads, yet with minimal dust and no squeaking ET500: Aggressive Street - Provides additional stopping power over ET300; low dust and little to no squeaking. ET700-900: Advanced Street - For very adventurous street driving. Not for use on the track, as high temperatures will greatly accelerate pad wear. For track racing, use our XT-Series brake pads. RB XT-Series Motorsports Compounds The XT Series compounds were developed to handle the toughest track braking conditions. All of our XT series can deliver consistent brake torque, are excellent in modulation and highly resistant to wear, friendly to rotors, brake dust is easy to clean, and brake control. XT910: Medium initial bite, medium to high friction and brake torque. XT960: Medium initial bite, high friction and brake torque. XT970: High initial bite, Extremely high friction and brake torque. Since these pads are formulated for track/high temperature use, using them on the street may result some unfavorable situations such as brake squeal, dirty wheels, less brake friction at cold temperatures, and excessive rotor wear. For street driving, we recommended that you use our ET series pads. Break-In All brake pads are recommended to be bedded-in properly according to the proper break-in procedure to assure optimal performance. Break Pad Performance The overall brake pad performance can be affected by the rotor material and its surface finish, calipers, and brake bias. Brake Pad Replacement Important to know! Since the brake pad consists of the friction material, insulator, bonding agent, and a steel plate, the pads must be replaced when the "non-steel" material wears down to approximately the same thickness as the steel back plate or to the grooves in the pad (if applicable). However, since the groove depth varies from one pad manufacturer to another, we do not recommend running the pad thinner than 4mm (0.16"). This minimum wear thickness is a checkpoint for pad replacement to prevent severe damage from occurring to the brake system, including rotors and calipers. http://www.apex-speed.com/images/ven...k/pad_wear.jpg http://www.apex-speed.com/images/div.jpg http://www.apex-speed.com/images/det...e3d76cf1a0.jpg RacingBrake - Aluminum Caliper Upgrade Kit: $1425.99 Stock sized rotors are required and not included with this kit. This kit can be used as a caliper upgrade for OEM or aftermarket rotors (with the same size and offset). It is highly recommend for people who are considering this option to purchase the complete kit to assure the compatibility and peak performance of the brake system. Please note that any issue associated with the non-RB rotors is not warranted. This kit comes with the following:
For street driving, here are the benefits:
http://www.apex-speed.com/images/ven...k_calipers.jpg RacingBrake Calipers RacingBrake Calipers are made from forged 6061-T6 aluminum and precisely machined to every detail. Stock calipers - aluminum (Brembo) or cast iron (06-08 WRX) are mass-produced and are usually made through a casting or extrusion process which is not as dense and strong in structure as forging. - Caliper Body: Made of forged 6061-T6. Light weight at only 4.5lbs, these new RB4000 calipers are re-designed and built for the toughest brake jobs with extended service life before any rebuild is required. - Low Profile: Together with RB Center-Mount design two-piece rotors, you hardly even need to require a spacer to install the kit. - Piston Material: Made of stainless steel instead of aluminum commonly used by other caliper mfgrs which can substantially reduce the heat transfer (approx 1/10 of aluminum) from the pad to brake fluid. Pistons are vented to further reduce the heat contact area and improve air circulation thereby reducing more heat transfer. - Dust Seal: Our dust seal is of built-in type (instead of external boot type) uniquely designed to shield the dust and foreign material from contamination and will not rip - as commonly seen on boot type dust seals. http://www.apex-speed.com/images/ven..._dust_seal.jpg - Hardware: Brake pad pins and banjo connections were re-designed for easier brake line connection and brake pad replacement. - Surface Coating: Powder coating with most durable finish for lasting appeal. - Hardware: Most hardware is made of stainless steel for durable performance and appearance. - Never Get Lost Bleeder Cap: Newly designed with a retaining loop so you will never have to find it again and/replace the lost ones. (made of durable EPDM) http://www.apex-speed.com/images/ven...leeder_cap.jpg RB ET Series Brake Pads From daily driver to dedicated tracking racing enthusiast, our ET-series brake pads provide a selection of various compounds that makes them easy to choose and use at an affordable cost. ET-Series Performance Street Compounds The ET Series compounds provide excellent modulation, consistent friction and torque output, and can be run from ambient temperature, even during cold winter mornings. ET300: Performance Street - Delivers braking performance beyond stock pads, yet with minimal dust and no squeaking ET500: Aggressive Street - Provides additional stopping power over ET300; low dust and little to no squeaking. ET700-900: Advanced Street - For very adventurous street driving. Not for use on the track, as high temperatures will greatly accelerate pad wear. For track racing, use our XT-Series brake pads. RB XT-Series Motorsports Compounds The XT Series compounds were developed to handle the toughest track braking conditions. All of our XT series can deliver consistent brake torque, are excellent in modulation and highly resistant to wear, friendly to rotors, brake dust is easy to clean, and brake control. XT910: Medium initial bite, medium to high friction and brake torque. XT960: Medium initial bite, high friction and brake torque. XT970: High initial bite, Extremely high friction and brake torque. Since these pads are formulated for track/high temperature use, using them on the street may result some unfavorable situations such as brake squeal, dirty wheels, less brake friction at cold temperatures, and excessive rotor wear. For street driving, we recommended that you use our ET series pads. Break-In All brake pads are recommended to be bedded-in properly according to the proper break-in procedureto assure optimal performance. Break Pad Performance The overall brake pad performance can be affected by the rotor material and its surface finish, calipers, and brake bias. Brake Pad Replacement Important to know! Since the brake pad consists of the friction material, insulator, bonding agent, and a steel plate, the pads must be replaced when the "non-steel" material wears down to approximately the same thickness as the steel back plate or to the grooves in the pad (if applicable). However, since the groove depth varies from one pad manufacturer to another, we do not recommend running the pad thinner than 4mm (0.16"). This minimum wear thickness is a checkpoint for pad replacement to prevent severe damage from occurring to the brake system, including rotors and calipers. http://www.apex-speed.com/images/ven...k/pad_wear.jpg |
Members of the forums we sponsor have become accustomed to reading quotes like these on a regular basis.
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
How Do We Do It? From the beginning, our operation was set up to function as rapidly and efficiently as possible. Most of our order processing system is automated which means that an order can be completely processed and ready for pick up within minutes of the order being placed. Unlike many of our competitors, APEX Motorsports is a stocking distributor for most of the brands we carry and not a dedicated drop shipper. This allows us to ship in stock items the same day or next if the order is received after our last pick up. In the event that an item is out of stock, APEX Motorsports has access to multiple extensive distributor networks and can draw on the inventories of dozens of regional warehouses across the country and ship the item from the warehouse closest to you. APEX Motorsports has another key advantage over our competition. Our physical location. Like Amazon, Zappos, and many other major shippers APEX Motorsports is located in Louisville, Ky. which places us within 600 miles of more than 60% of the United States population. It also places us only a few miles from the UPS World Hub. That means that once your order leaves our loading dock it doesn't have to travel 1-2 days to be processed before being directed to your address. It is done within hours of the order being placed and is on it's way to your door, more than 60% of which aren't very far down the road. Below is a map displaying the estimated delivery times for orders shipped from APEX Motorsports. http://www.apex-speed.com/images/shipmap.gif |
Would have been buying this caliper set Chase :emoticon3:
|
cant wait to pick mine up from racingbrake. also the rear caliper is in the works. this package deal is a total steal for best oem size brakes period
|
Quote:
|
No, the rears are not out yet. Soon.....
|
Out of curiosity why did they stick with a 4 piston vs a 6 piston?
|
Quote:
|
Quote:
WOW these things can stop like no other.....and that was just with the rotors and stock calipers. And no brake fade in really hot weather...118 degrees. |
Quote:
|
Quote:
|
Quote:
|
How much are just the rotors with pads?
|
Quote:
|
All times are GMT -5. The time now is 04:13 PM. |
Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.