Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Cold Air Inductions
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums

Showing results 1 to 30 of 440
Search took 0.07 seconds.
Search: Posts Made By: Pt_killa
Forum: Forced Induction - V6 05-15-2015, 10:25 PM
Replies: 13
Views: 467
Posted By Pt_killa
The turbo in the link would work in a twin setup....

The turbo in the link would work in a twin setup. According to the specs in the description, this distributor mated a gt35 turbine wheel with a smaller 56mm to4e compressor. The .68ar T4 housing...
Forum: Forced Induction - V6 04-09-2015, 10:38 AM
Replies: 18
Views: 896
Posted By Pt_killa
Is there a check valve between the pass side and...

Is there a check valve between the pass side and intake manifold? If not you will pressurize the crankcase under boost which will push oil out of the clean side.

On my current setup I just run...
Forum: Forced Induction - V6 04-09-2015, 09:26 AM
Replies: 18
Views: 896
Posted By Pt_killa
I think we all thought you were only running the...

I think we all thought you were only running the elite can but you're running it in addition to the sts pcv dirty side can, so it should be fine were it is. I'm assuming the sts switch valve closes...
Forum: Forced Induction - V6 04-08-2015, 05:00 PM
Replies: 18
Views: 896
Posted By Pt_killa
I agree, you should run the can on the passenger...

I agree, you should run the can on the passenger side. I leave the clean side open with a large valve cover air filter from the autoparts store, a very small amount of unmetered air may get through...
Forum: Forced Induction - V6 04-01-2015, 09:25 AM
Replies: 64
Views: 2,506
Posted By Pt_killa
Fortunately the blower intake manifold looks to...

Fortunately the blower intake manifold looks to be machined from solid billet so no need to worry about ugly welds for most of the setup, only intake pipes maybe.
Forum: Forced Induction - V6 03-30-2015, 04:21 PM
Replies: 15
Views: 614
Posted By Pt_killa
Mityguy, your car will run like stock with the...

Mityguy, your car will run like stock with the IPF kit until you smash the gas. Your gas mileage won't change much if you just cruise around. If you already service your car at the normal intervals,...
Forum: Forced Induction - V6 03-30-2015, 12:47 PM
Replies: 938
Views: 72,368
Posted By Pt_killa
I have very limited tuning knowledge but are...

I have very limited tuning knowledge but are companies known for hiding certian tables in ecu's, why would GM/Bosch hide certian tables but not others, is HP tuners not capable of reading and editing...
Forum: Forced Induction - V6 03-26-2015, 10:56 PM
Replies: 64
Views: 2,506
Posted By Pt_killa
The roots FI setup is the least compilcated FI...

The roots FI setup is the least compilcated FI setup mechanically. No intercooler piping, wastegate's, bov (integrated into sc), oil lines etc. Therefore, as long as the blower is sized right and...
Forum: Forced Induction - V6 03-25-2015, 02:46 PM
Replies: 64
Views: 2,506
Posted By Pt_killa
No factory kit from Chevy but there is an...

No factory kit from Chevy but there is an aftermarket one on the bowtie v6 forums:
http://www.bowtie v6*/forum/viewtopic.php?f=12&t=2747 (cam5 wouldnt let me upload the link so to view just remove...
Forum: Forced Induction - V6 03-25-2015, 02:38 PM
Replies: 15
Views: 614
Posted By Pt_killa
The two top kits that people on this site use are...

The two top kits that people on this site use are the Fab. Twin Turb's and IPF super. You can't go wrong with either setup, both are good with power and reliability. Once you commit to buying a kit,...
Forum: V6 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 03-18-2015, 01:00 PM
Replies: 18
Views: 1,512
Posted By Pt_killa
bump for insanely great deal!

bump for insanely great deal!
Forum: Forced Induction - V6 02-24-2015, 01:45 PM
Replies: 43
Views: 1,495
Posted By Pt_killa
Nice runs! finally more turbo cars are catching...

Nice runs! finally more turbo cars are catching up with the nitrous guys. It sounds like you have an automatic, if you have the stock converter be very careful when staging and holding the ebrake. My...
Forum: Forced Induction - V6 02-22-2015, 02:49 PM
Replies: 8
Views: 684
Posted By Pt_killa
Generally, the less backpressure after the turbo,...

Generally, the less backpressure after the turbo, the faster the turbo will spool since there is less restriction on spinning the exhuast wheel. The only potential problem is that the turbo could...
Forum: Forced Induction - V6 02-15-2015, 09:38 AM
Replies: 8
Views: 653
Posted By Pt_killa
use a 62-70mm compressor turbo and a small ar...

use a 62-70mm compressor turbo and a small ar exhuast housing or run a large divided housing with a quick spool valve in order to minimize spool time.
Forum: Forced Induction - V6 01-25-2015, 10:07 AM
Replies: 6
Views: 661
Posted By Pt_killa
Side pillar pod $75:...

Side pillar pod $75:...
Forum: Forced Induction - V6 01-23-2015, 09:08 AM
Replies: 22
Views: 1,134
Posted By Pt_killa
Geared Centri vs geared twins, will be the v6...

Geared Centri vs geared twins, will be the v6 showdown of the year. You two aren't far from each other, you should meet up at a strip halfway and run together.
Forum: Forced Induction - V6 01-22-2015, 01:55 PM
Replies: 22
Views: 1,134
Posted By Pt_killa
When Magnum hooks with his 1LE diff, i think...

When Magnum hooks with his 1LE diff, i think he'll break the long standing v6 1/4 mile record on camaro5 of 11.8.
Forum: Forced Induction - V6 01-19-2015, 04:37 PM
Replies: 2
Views: 391
Posted By Pt_killa
Try removing the dipstick when the car's running...

Try removing the dipstick when the car's running and see if the noise goes away. A common symptom of poor crankcase evac on a FI LLT is a squeaking noise from the enigne.
Forum: Forced Induction - V6 01-18-2015, 03:06 PM
Replies: 23
Views: 1,362
Posted By Pt_killa
+1, DIY is most cost effective route as long as...

+1, DIY is most cost effective route as long as you know what you're doing. Fortunately, there's tons of knowledge available now on the forums about FI on the LLT/LFX.
Forum: Camaro V6 LLT Engine, Exhaust, and Bolt-Ons 01-14-2015, 09:52 AM
Replies: 176
Views: 16,327
Posted By Pt_killa
Just installed vitesse a few weeks ago and the...

Just installed vitesse a few weeks ago and the spool is noticeably faster on the rear twins.

Vent, no issues with the stabili trac on my car.
Forum: Forced Induction - V6 01-10-2015, 09:14 AM
Replies: 23
Views: 1,362
Posted By Pt_killa
If you don't want to dish out the cash for a ball...

If you don't want to dish out the cash for a ball bearing turbo, a cheaper journal bearing turbo in the rear will be just as reliable since the turbo doesn't get as hot back there but make sure to...
Forum: Forced Induction - V6 01-08-2015, 09:55 AM
Replies: 15
Views: 775
Posted By Pt_killa
wow can't beat that deal!

wow can't beat that deal!
Forum: Forced Induction - V6 01-08-2015, 08:18 AM
Replies: 15
Views: 775
Posted By Pt_killa
Talk to magnum for more in-depth details since...

Talk to magnum for more in-depth details since he's done this already, but all you need to do is buy a used SS stock 2-piece driveshaft for cheap and swap in the rear half that bolts to the diff and...
Forum: Forced Induction - V6 10-06-2014, 02:07 PM
Replies: 255
Views: 15,080
Posted By Pt_killa
Happy to hear you're up and running. A boost...

Happy to hear you're up and running. A boost controller will help definitely help! Also, where are you referencing the boost for the wastegate? Using a boost controller and referencing from the IM...
Forum: Forced Induction - V6 09-23-2014, 09:51 AM
Replies: 255
Views: 15,080
Posted By Pt_killa
For the OP, if you decide to keep the car and sts...

For the OP, if you decide to keep the car and sts setup, after looking at the sizing and similar comp map, the s200sx turbo with .83ar is fine for a single. The key to buying a turbo for a...
Forum: Forced Induction - V6 09-20-2014, 10:51 AM
Replies: 177
Views: 17,022
Posted By Pt_killa
Could be vacuum leak somewhere? Also is that an...

Could be vacuum leak somewhere? Also is that an RX catch can, the drain on the catch can could be open? Check to see if its turned all the way by turning the valve to the left, the drain will be...
Forum: Forced Induction - V6 08-31-2014, 09:46 AM
Replies: 17
Views: 1,669
Posted By Pt_killa
Poormc, I custom built a remote mount in my...

Poormc, I custom built a remote mount in my driveway, running for over 50k miles (332whp 305wtq, 13.4 @ 111mph). I have a parts list in excel format that documents all of the expenses if you want...
Forum: Forced Induction - V6 08-05-2014, 02:39 PM
Replies: 35
Views: 3,423
Posted By Pt_killa
Nice, can't go wrong with a daily turbo 6! As...

Nice, can't go wrong with a daily turbo 6! As another testament to others on FI reliablility, I've put 60k miles my the remote turb kit since 2011 with 30k of them in 2011 alone! I'm at 85k total but...
Forum: Forced Induction - V6 05-13-2014, 01:11 PM
Replies: 938
Views: 72,368
Posted By Pt_killa
Good job, replace the spectre piping asap Also,...

Good job, replace the spectre piping asap Also, have you thought about investing in a hump hose coupler to use at the intercooler or TB to help with the flexing?
Forum: Forced Induction - V6 03-30-2014, 12:59 PM
Replies: 1
Views: 545
Posted By Pt_killa
Use the oil pressure sensor port that is attached...

Use the oil pressure sensor port that is attached to the bottom of the oil filter housing. You can use a 27mm deep well socket or oil sensor remover to remove the stock sensor. The thread for the...
Showing results 1 to 30 of 440

 
Forum Jump

All times are GMT -5. The time now is 02:03 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2015, vBulletin Solutions, Inc.