Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Apex Paul
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums

Showing results 1 to 30 of 500
Search took 0.10 seconds.
Search: Posts Made By: blake-b
Forum: Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum 05-23-2015, 09:39 PM
Replies: 5
Views: 162
Posted By blake-b
There are plenty of site sponsors that sell them....

There are plenty of site sponsors that sell them. It is a holiday weekend and many may not be as active on the forums. In fact, if you go to the sponsors classifieds under the audio section, there is...
Forum: Cosmetic Maintenance: Washing, Waxing, Detailing, Bodywork, Protection 05-18-2015, 02:45 AM
Replies: 14
Views: 564
Posted By blake-b
This is the thread you want ...

This is the thread you want (http://www.camaro5.com/forums/showthread.php?t=329242)

Inspired by that thread, I added three flourescent fixtures (I converted from T12 to T8) and used 5000k T8...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 05-18-2015, 02:10 AM
Replies: 21
Views: 493
Posted By blake-b
Does this picture help? I just saw your other...

Does this picture help? I just saw your other post. When doing an LS3 conversion, you replace your L99 front cover with an LS3 front cover. You can buy an LS3 conversion kit that contains everything...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 05-18-2015, 12:36 AM
Replies: 21
Views: 493
Posted By blake-b
In the diagram, it is part 205 (GM 12606358) and...

In the diagram, it is part 205 (GM 12606358) and is internal. You cannot see without removing the front cover. It is the upper gear for the timing chain.
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 05-16-2015, 05:49 PM
Replies: 4
Views: 163
Posted By blake-b
Maybe I'm not understanding, I thought you asked...

Maybe I'm not understanding, I thought you asked if you could remove the factory fuel bucket, remove the factory pump, put a Walbro 450 in it's place and then put the factory bucket back in the tank?...
Forum: Off-topic Discussions 05-16-2015, 04:25 PM
Replies: 43
Views: 1,208
Posted By blake-b
Okay, I returned. The Posse Comitatus Act...

Okay, I returned.

The Posse Comitatus Act limits the powers of the federal government in using its military personnel to act as domestic law enforcement personnel.

Just saw this on another...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 05-16-2015, 03:46 PM
Replies: 4
Views: 163
Posted By blake-b
Technically yes, you can. However, what will...

Technically yes, you can. However, what will control the pump? I'm not sure the factory FPCM will play nicely with a pump that much larger than stock. The stock fuel hat won't work with either. Take...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 05-15-2015, 06:04 PM
Replies: 21
Views: 493
Posted By blake-b
Sent you a PM. Try starting your search around p...

Sent you a PM. Try starting your search around p 5356
Forum: Off-topic Discussions 05-15-2015, 12:54 PM
Replies: 43
Views: 1,208
Posted By blake-b
I had a bunch of stuff typed up but it would be...

I had a bunch of stuff typed up but it would be for naught to post it. You should never argue with the ignorant as they will drag you down to their level and beat you with experience.

nitrosteve,...
Forum: Forced Induction - V8 05-15-2015, 12:38 PM
Replies: 156
Views: 3,233
Posted By blake-b
I'll probably never have a time slip for my turbo...

I'll probably never have a time slip for my turbo setup because there are no tracks around here. The closest one is an hour away and rumor is it is closing. Yes, I could travel to a track but then...
Forum: Forced Induction - V8 05-14-2015, 02:19 PM
Replies: 156
Views: 3,233
Posted By blake-b
No PD experience here. I went from 1026whp with...

No PD experience here.
I went from 1026whp with a Ysi to 1026whp twin turbo setup and the turbos are a lot more fun.

Same engine, same setup (cam change was the only thing done when changing to...
Forum: Audio / Visual / Electronics/ Gauges / Nav 05-13-2015, 09:26 PM
Replies: 4
Views: 515
Posted By blake-b
The OP hasn't been logged into the site since...

The OP hasn't been logged into the site since December of 2014. I'd suggest calling or texting the number in the original ad...
Forum: Suspension / Brakes / Chassis 05-13-2015, 06:38 PM
Replies: 35
Views: 1,052
Posted By blake-b
BMR Trailing arms (TR002 Red) BMR Delrin Upper...

BMR Trailing arms (TR002 Red)
BMR Delrin Upper control arm bushings (BK039 Red)
BMR Toe rods (TCA026 Red with BK017 bushings)
PST Polyurethane subframe bushings (Black)
1LE front sway bar
32mm...
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 05-13-2015, 03:56 PM
Replies: 7
Views: 260
Posted By blake-b
You're welcome. I don't remember needing an...

You're welcome.

I don't remember needing an extension nearly that long. The top bolt will be TOUGH to get to. The one on either side of it that are slightly lower will be a little easier. For the...
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 05-13-2015, 03:21 PM
Replies: 7
Views: 260
Posted By blake-b
Will any specialty tools be needed? No, regular...

Will any specialty tools be needed?
No, regular tools in metric sizes (or if you know the SAE equivalent)
Do I need to drain the trans fluid completely beforehand?
I would. It will be less messy...
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 05-13-2015, 10:11 AM
Replies: 1
Views: 196
Posted By blake-b
Bump.

Bump.
Forum: Forced Induction - V8 05-12-2015, 04:26 PM
Replies: 17
Views: 516
Posted By blake-b
I've got an ls2 darton MID wet sleeved block...

I've got an ls2 darton MID wet sleeved block being built into an engine very soon.
Forum: Forced Induction - V8 05-08-2015, 03:37 PM
Replies: 6
Views: 343
Posted By blake-b
You won't benefit from a larger throttle body....

You won't benefit from a larger throttle body. Stock TBs have made well over 1k to the wheels. I had a Fast 102/102 TB and made 825whp with a Ysi. I sold that stuff and went to a stock intake and TB....
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 05-08-2015, 01:39 PM
Replies: 5
Views: 281
Posted By blake-b
ARP LS1 stuff will work. The bolts are the same. ...

ARP LS1 stuff will work. The bolts are the same.

http://arp-bolts.com/kits/Make.php?_Make=303&_EngModelID=*

Then click on "driveline"

flywheel: 330-2802...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 05-08-2015, 01:27 PM
Replies: 8
Views: 378
Posted By blake-b
No. There is nothing wrong with the stock GM...

No. There is nothing wrong with the stock GM wires.
Forum: Forced Induction - V8 05-07-2015, 09:51 PM
Replies: 21
Views: 786
Posted By blake-b
Sell the headers and go AGP. Power is addictive...

Sell the headers and go AGP. Power is addictive and very soon, 600whp won't be enough and you'll want more. It happens to all of us.

The base AGP kit will easily make 600+whp on an otherwise...
Forum: Forced Induction - V8 05-07-2015, 09:26 PM
Replies: 21
Views: 786
Posted By blake-b
I went from a Ysi to an AGP kit. The AGP with no...

I went from a Ysi to an AGP kit. The AGP with no other mods will give the power the ECS + cam will and the AGP kit has much more room to grow.

You'll be money ahead in the long run if you just...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 05-07-2015, 12:16 PM
Replies: 5
Views: 281
Posted By blake-b
Jack the back end of the car higher than the...

Jack the back end of the car higher than the front and you can take engine and trans out together. The angle of the car makes it much easier.

I have also done it with the car level and with the...
Forum: Forced Induction - V8 05-07-2015, 11:53 AM
Replies: 9
Views: 399
Posted By blake-b
I've made just over 1k to the wheels with a...

I've made just over 1k to the wheels with a Squash double (he doesn't make triples), stock feed line and -6 return, and ID1000s with plenty of room to spare.

A fast intake is a waste of money...
Forum: Engine | Exhaust | Bolt-On | Drivetrain Modifications 05-07-2015, 02:08 AM
Replies: 16
Views: 582
Posted By blake-b
In order to replace a piston correctly, you have...

In order to replace a piston correctly, you have to disassemble the engine to get it out. Heads are removed, etc. Changing pistons also means your entire rotating assembly should be balanced.

In...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 05-05-2015, 04:12 PM
Replies: 5
Views: 226
Posted By blake-b
Remove trans and then unbolt the two bolts...

Remove trans and then unbolt the two bolts holding it (slave cylinder) on. It slides over the input shaft of the trans. Here is a pic of one installed. You would also undo the clutch fluid line...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 05-05-2015, 12:49 PM
Replies: 5
Views: 226
Posted By blake-b
Do you mean taking the plastic bearing part out...

Do you mean taking the plastic bearing part out and replacing it with a billet piece? If so, you just pop off the little white/gray retaining ring on the top (you will reuse it so be careful), take...
Forum: Transmission / Driveline 05-04-2015, 04:44 PM
Replies: 0
Views: 100
Posted By blake-b
SOLD BMR driveshaft safety loop for V8 manual/V6 auto

SOLD
Brand new, never installed in grey hammertone finish.

Here's the link to BMR's site about it:
http://bmrsuspension.com/?page=products&productid=465&superpro=0

$60 shipped.
SOLD
Forum: Transmission / Driveline 05-04-2015, 04:41 PM
Replies: 2
Views: 198
Posted By blake-b
SOLD 3.45 differential

SOLD

18k miles on a 2010 3.45 differential.

The differential has Pfadt bushings, billet caps, and the JRE posi mod in it.

For full disclosure: early in it's life, it had a set of Richmond...
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 05-04-2015, 04:35 PM
Replies: 1
Views: 196
Posted By blake-b
SOLD ID1000 injectors

SOLD
I've had these for a couple years and only put around 6k on them. It's time to go to something bigger. These are the ones with a 48mm oring to oring body.

They have been in a plastic bag...
Showing results 1 to 30 of 500

 
Forum Jump

All times are GMT -5. The time now is 07:09 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2015, vBulletin Solutions, Inc.