Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Vararam
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums


Showing results 1 to 30 of 500
Search took 0.09 seconds.
Search: Posts Made By: SSMickey
Forum: Camaro Issues / Problems | Warranty Discussions | TSB and Recalls 11-08-2018, 06:57 PM
Replies: 4
Views: 5,297
Posted By SSMickey
Try this if you want, but I take no...

Try this if you want, but I take no responsibility.
All of this is done at the PSCM connector.

jump pins 4 & 9(tan)
jump pins 3 & 8(tan/black)
This is the High Speed GM LAN

jump pins 2 &...
Forum: Camaro Issues / Problems | Warranty Discussions | TSB and Recalls 11-08-2018, 06:47 PM
Replies: 4
Views: 5,297
Posted By SSMickey
Just looked at the wiring diagram for a 15. The...

Just looked at the wiring diagram for a 15. The High Speed GM LAN runs through the Power Steering Control Module then to the PCM. Without the PSCM there is a break in the network. That's why you have...
Forum: Camaro Issues / Problems | Warranty Discussions | TSB and Recalls 11-08-2018, 09:46 AM
Replies: 4
Views: 5,297
Posted By SSMickey
First check powers and grounds at the PCM. Is...

First check powers and grounds at the PCM. Is this a car an auto or manual trans. GM has the data lines set up in such a fashion that if a module goes bad or a data line gets broke, you will lose...
Forum: Tuning / Diagnostics -- engine and transmission 10-25-2018, 07:02 PM
Replies: 6
Views: 1,552
Posted By SSMickey
Didn't know this was possible. I'll have to look...

Didn't know this was possible. I'll have to look into what else can be done. Might open up some interesting possibility's. Thanks for the info.
Forum: Forced Induction - V8 10-25-2018, 06:56 PM
Replies: 7
Views: 1,771
Posted By SSMickey
3.75, but my cam has a lot of overlap and bleeds...

3.75, but my cam has a lot of overlap and bleeds boost. Not really a boost friendly cam. I just put it in the first of the year then decided to go FI and didn't feel like pulling it out.
Forum: Tuning / Diagnostics -- engine and transmission 10-22-2018, 03:30 PM
Replies: 6
Views: 1,552
Posted By SSMickey
So your setup allowed you to alter the BCM...

So your setup allowed you to alter the BCM calibration? Please explain how you did this for my knowledge. It just might come in handy one day. I know how to flash a module with SPS and Tis2Web using...
Forum: Forced Induction - V8 10-22-2018, 03:23 PM
Replies: 7
Views: 1,771
Posted By SSMickey
Sorry it took so long. I honestly forgot about...

Sorry it took so long. I honestly forgot about this post. Procharger sent out a smaller pulley and got the boost to 9-9.5 as I initially requested. Big shout out to Bob at Brute Speed for assisting...
Forum: Tuning / Diagnostics -- engine and transmission 10-13-2018, 08:34 PM
Replies: 6
Views: 1,552
Posted By SSMickey
To the best of my knowledge, only GM currently...

To the best of my knowledge, only GM currently has the ability to alter the BCM calibration.
Forum: Mechanical Maintenance: Break-in / Oil & Fluids / Servicing 10-05-2018, 07:45 PM
Replies: 3
Views: 3,108
Posted By SSMickey
No calibration needed if you replace the BPPS....

No calibration needed if you replace the BPPS. The BBPS sends a voltage signal to the BCM when you step on the brake pedal. If the sensor is messed up and is constantly sending out a signal the BCM...
Forum: Mechanical Maintenance: Break-in / Oil & Fluids / Servicing 10-05-2018, 07:14 PM
Replies: 3
Views: 3,108
Posted By SSMickey
Brake pedal position switch is what your looking...

Brake pedal position switch is what your looking for. It sends a signal to the BCM and the BCM turns on the brake lights. It has no direct control over turning on the brake lights like the old brake...
Forum: Camaro Issues / Problems | Warranty Discussions | TSB and Recalls 09-30-2018, 06:05 PM
Replies: 20
Views: 12,692
Posted By SSMickey
If your engine is an L99, I'll bet you have a...

If your engine is an L99, I'll bet you have a collapsed AFM lifter. Check your code and misfire data stream. The AFM lifters are on 1, 4, 6 and 7. If the misfire is one of those cylinders, pull the...
Forum: Forced Induction - V8 09-29-2018, 04:33 PM
Replies: 10
Views: 1,162
Posted By SSMickey
I know nothing about CARB and Cali think god. SC...

I know nothing about CARB and Cali think god. SC could care less what you do to your car.

Any belt driven blower; ProCharger, Vortech, Paxton, Maggie or SLP will take power to run. Turbos do not...
Forum: Tuning / Diagnostics -- engine and transmission 09-28-2018, 09:29 PM
Replies: 1
Views: 546
Posted By SSMickey
P0036 is a heater circuit code. Your tuner...

P0036 is a heater circuit code. Your tuner probably missed turning off that code. Look at your tune and see if P0030, P0050 and P0056 are turned off. All 4 codes are for the heater circuit of the...
Forum: Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum 09-26-2018, 07:35 PM
Replies: 4
Views: 1,078
Posted By SSMickey
You can grab switched power and ground at the...

You can grab switched power and ground at the power outlets in the center console.
Forum: 5th Gen Camaro SS LS LT General Discussions 09-21-2018, 08:29 PM
Replies: 2
Views: 1,312
Posted By SSMickey
For some reason, Rock Auto, GM Parts Direct and...

For some reason, Rock Auto, GM Parts Direct and GM Parts Online don't show the part. Just go to a dealer and have them look it up. It's the fresh air inlet line for the PCV system.
Forum: Forced Induction - V8 09-19-2018, 07:21 PM
Replies: 7
Views: 1,771
Posted By SSMickey
So Procharger said the smoke leak is normal. Not...

So Procharger said the smoke leak is normal. Not sure I agree but there sending out another pulley to hopefully get the boost level to what I initially asked for. I'll post back when I get it...
Forum: Forced Induction - V8 09-16-2018, 01:52 PM
Replies: 7
Views: 1,771
Posted By SSMickey
ProCharger P1X boost leak?

Finally finished up the install and tuning. ProCharger said they pulleyed the head unit for 9 lbs at 6500 rpm. I'm only seeing 6.5 at 6500. My vendor asked that I check for belt slip and/or a boost...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 09-14-2018, 07:22 PM
Replies: 11
Views: 2,789
Posted By SSMickey
I have moved mine. As long as you use quality...

I have moved mine. As long as you use quality wires you won't have a problem. I bought bulk Taylor wires, boots and terminals from Summit and made my own. Just make sure you have a set of crimpers...
Forum: Forced Induction - V8 08-31-2018, 09:32 PM
Replies: 11
Views: 4,086
Posted By SSMickey
These pics were sent from ProCharger. Might help...

These pics were sent from ProCharger. Might help someone with running the charge pipes up to the throttle body. In addition, leave the fans out until you have the charge piping run and in place....
Forum: 5th Gen Camaro SS LS LT General Discussions 08-25-2018, 09:45 PM
Replies: 4
Views: 1,252
Posted By SSMickey
If your careful, you won't need another belt....

If your careful, you won't need another belt. They can be reused. Just walk it off the back of the crank pulley and walk it back on from the back of the crank pulley. If you bought the belt from GM...
Forum: Forced Induction - V8 08-25-2018, 03:30 PM
Replies: 11
Views: 4,086
Posted By SSMickey
Has there been any resolution on this problem? I...

Has there been any resolution on this problem? I have the same year car, same kit and head unit and the same problem. I trimmed the fan but that didn't help. I have not trimmed the sub frame yet and...
Forum: 5th Gen Camaro SS LS LT General Discussions 08-24-2018, 07:09 PM
Replies: 4
Views: 1,252
Posted By SSMickey
A bad expansion valve won't keep the compressor...

A bad expansion valve won't keep the compressor from coming on. Are you sure you plugged in the compressor? As for your pressures, are you sure you opened the low side valve? The system should be...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 10-30-2017, 07:00 PM
Replies: 18
Views: 4,412
Posted By SSMickey
Finished the valve train tear down today and...

Finished the valve train tear down today and found 3 more bearings with slop in them. Found a new set of rockers with the bushing kit already installed from Steve Morris Engines. Nothing against the...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 10-27-2017, 05:55 PM
Replies: 18
Views: 4,412
Posted By SSMickey
Trunnion failure

Just finished diagnosing the noise from the car today. #7 intake rocker trunnion bearing failure. Yes, it was the Comp trunnion upgrade kit with about 25k on it. What reliable options are out there?...
Forum: 5th Gen Camaro SS LS LT General Discussions 05-15-2016, 12:23 PM
Replies: 3
Views: 1,148
Posted By SSMickey
Thanks, your pictures are a huge help. According...

Thanks, your pictures are a huge help. According to your pictures, they installed a windshield for an automatic with remote start in my car and popped the bracket off. Or GM changed the windshield...
Forum: 5th Gen Camaro SS LS LT General Discussions 05-15-2016, 11:57 AM
Replies: 3
Views: 1,148
Posted By SSMickey
Need verification of windshield

Safelight has tried 4 times to get the correct windshield for my car. A 2010 SS 6 speed with out remote start. Finally, they said they had the correct windshield and installed it when I was not...
Forum: Wheels and Tires Talk Sponsored by The Tire Rack 09-26-2015, 11:33 AM
Replies: 6
Views: 4,469
Posted By SSMickey
Pedders USA was running 305's at all 4 corners...

Pedders USA was running 305's at all 4 corners and there car was lowered. You'll need wheels with the correct offset to do this, but it can be done. I know Forgeline can build the wheels to do this...
Forum: Camaro Issues / Problems | Warranty Discussions | TSB and Recalls 06-07-2015, 08:27 PM
Replies: 4
Views: 1,522
Posted By SSMickey
Check your coolant level first. Will your car...

Check your coolant level first. Will your car come up to normal operating temp? If not, or if it takes a long time, I'd suspect a faulty thermostat. If all that is good, I'd get hold of a good...
Forum: Suspension / Brakes / Chassis 10-28-2014, 03:44 PM
Replies: 11
Views: 1,649
Posted By SSMickey
Toe is not measured in degrees. Only caster and...

Toe is not measured in degrees. Only caster and camber are measured in degrees. Never seen an option on an alignment machine for degrees of toe. Only fraction or decimal readout.
Forum: Wheels and Tires Talk Sponsored by The Tire Rack 07-27-2014, 08:16 PM
Replies: 1
Views: 848
Posted By SSMickey
I'd get new sensors so it's just a quick...

I'd get new sensors so it's just a quick tire/wheel swap twice a year plus your TPMS stays functional.
Showing results 1 to 30 of 500

 
Forum Jump

All times are GMT -5. The time now is 02:55 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.