Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Classic Industries
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums

Showing results 1 to 30 of 37
Search took 0.02 seconds.
Search: Posts Made By: 08G8V8
Forum: Forced Induction - V8 04-10-2013, 09:18 AM
Replies: 45
Views: 1,904
Posted By 08G8V8
The dealer will just load the supplied tune that...

The dealer will just load the supplied tune that comes pre-installed on the handheld tuner that SLP provides with their kit, just as if you bought the kit and installed it yourself in your garage. ...
Forum: Forced Induction - V8 04-07-2013, 08:18 PM
Replies: 53
Views: 2,525
Posted By 08G8V8
Yes, you could put the car on a dyno and have...

Yes, you could put the car on a dyno and have them use their wideband in your tailpipe to verify what you are getting on your wideband is accurate, or if you sensor is bad.

Is your wideband...
Forum: Forced Induction - V8 04-06-2013, 09:53 PM
Replies: 53
Views: 2,525
Posted By 08G8V8
My NGK AFX wideband reads between 9.0 and 16.0. ...

My NGK AFX wideband reads between 9.0 and 16.0. When letting off the throttle, when reading full air, it will read 16.0 or AIR. But with the foot on the throttle, even lightly, it won't read 16.0....
Forum: Forced Induction - V8 04-01-2013, 05:24 PM
Replies: 84
Views: 5,019
Posted By 08G8V8
I did that on my install as well.

I did that on my install as well.
Forum: Forced Induction - V8 03-28-2013, 11:06 PM
Replies: 57
Views: 2,726
Posted By 08G8V8
You should be around 11.5 AFR at WOT. If you see...

You should be around 11.5 AFR at WOT. If you see AFR of 12.5 and higher, you should have them look at the tune again.
Forum: Forced Induction - V8 02-19-2013, 06:42 PM
Replies: 2
Views: 408
Posted By 08G8V8
I used 5/32 hose on my install.

I used 5/32 hose on my install.
Forum: Forced Induction - V8 02-10-2013, 06:34 PM
Replies: 9
Views: 1,264
Posted By 08G8V8
I know nothing about this kit, but as far as...

I know nothing about this kit, but as far as getting boost/vacuum from your Maggie, there should be a nipple on the back of the unit with a rubber cap on it. On my G8, it is on the drivers side. ...
Forum: Forced Induction - V8 01-24-2013, 08:23 PM
Replies: 14
Views: 1,260
Posted By 08G8V8
I have the NGK AFX wideband.

I have the NGK AFX wideband.
Forum: Forced Induction - V8 01-19-2013, 05:50 PM
Replies: 8
Views: 955
Posted By 08G8V8
hmmmm.....I need to see about getting mine to do...

hmmmm.....I need to see about getting mine to do that. Thanks
Forum: Forced Induction - V8 01-19-2013, 05:47 PM
Replies: 8
Views: 955
Posted By 08G8V8
Is that -20.5psi a value you converted to get? ...

Is that -20.5psi a value you converted to get? Your Aeroforce gauges should be reading MAP in kpa. With the engine off but the key in the on position you would be at 0 manifold pressure, your...
Forum: Forced Induction - V8 09-20-2012, 03:42 PM
Replies: 64
Views: 4,588
Posted By 08G8V8
SRT10KLLR, you have the Lonnies fuel system,...

SRT10KLLR, you have the Lonnies fuel system, right? I think I remember seeing that. I have his dual pump system in my G8, and I know with the G8 system the line immediately lose fuel pressure when...
Forum: Forced Induction - V8 09-10-2012, 01:26 PM
Replies: 13
Views: 1,117
Posted By 08G8V8
I installed my Maggie myself with a buddy...

I installed my Maggie myself with a buddy initially. I had a shop do my cam install, as I felt I would rather not take on that project. I didn't pay twice for the labor of the Maggie install, as...
Forum: Forced Induction - V8 09-10-2012, 01:08 PM
Replies: 13
Views: 1,117
Posted By 08G8V8
I know there are a bunch of G8 folks who have...

I know there are a bunch of G8 folks who have just put a Maggie on their cars without issue, which also has active fuel management. I initially installed mine on my stock engine, but I only went...
Forum: Forced Induction - V8 01-11-2012, 12:17 AM
Replies: 60
Views: 2,135
Posted By 08G8V8
I'd be interested in replacement of my Kooks HF...

I'd be interested in replacement of my Kooks HF cats.
Forum: Forced Induction - V8 11-19-2011, 08:43 PM
Replies: 26
Views: 1,493
Posted By 08G8V8
Dang, that was super fast shipping. Congrats and...

Dang, that was super fast shipping. Congrats and enjoy!
Forum: Forced Induction - V8 11-15-2011, 09:37 AM
Replies: 30
Views: 1,753
Posted By 08G8V8
I did my install on my G8 with the help of a...

I did my install on my G8 with the help of a buddy. The only part we didn't do was pinning the crank. I took that to a local shop and they took care of that. 1 hour labor was well worth it for me....
Forum: Forced Induction - V8 10-30-2011, 01:04 AM
Replies: 5
Views: 511
Posted By 08G8V8
I'm sure the dyno shop would have a pressure...

I'm sure the dyno shop would have a pressure gauge they can screw onto your schrader valve to watch the fuel pressures during your dyno pull.
Forum: Forced Induction - V8 10-29-2011, 10:53 PM
Replies: 37
Views: 4,861
Posted By 08G8V8
Too bad you guys don't do stuff for the G8.

Too bad you guys don't do stuff for the G8.
Forum: Suspension / Brakes / Chassis 10-03-2011, 08:19 AM
Replies: 45
Views: 7,731
Posted By 08G8V8
I didn't think so, and didn't mean to say they...

I didn't think so, and didn't mean to say they were. Just from reading the first post asking about Brake Performance rotors, and then a bunch of replies from you, it didn't make sense to me.
...
Forum: Forced Induction - V8 10-02-2011, 10:53 PM
Replies: 15
Views: 1,271
Posted By 08G8V8
Look on the drivers side at the rear, there...

Look on the drivers side at the rear, there should be a nipple with a black cover on it. At least that is where it is on the TVS1900 on my G8.
Forum: Suspension / Brakes / Chassis 10-02-2011, 09:40 AM
Replies: 45
Views: 7,731
Posted By 08G8V8
Are these Granatelli rotors or Brake Performance...

Are these Granatelli rotors or Brake Performance rotors, or are they both the same?
Forum: Suspension / Brakes / Chassis 10-02-2011, 08:56 AM
Replies: 3
Views: 404
Posted By 08G8V8
I believe R1 Concepts is a vendor here on the...

I believe R1 Concepts is a vendor here on the forum.
Forum: Suspension / Brakes / Chassis 09-08-2011, 09:42 AM
Replies: 507
Views: 75,054
Posted By 08G8V8
THANKS, I understand. I was confused based on...

THANKS, I understand. I was confused based on the statement above from JusticePete stating the larger piston 1 being at the top(leading) position when mounted on the leading edge, and the pictures...
Forum: Suspension / Brakes / Chassis 09-07-2011, 10:43 PM
Replies: 507
Views: 75,054
Posted By 08G8V8
So I have not seen the CTS-V caliper, but based...

So I have not seen the CTS-V caliper, but based on JusticePete's response above, the larger piston is on the leading edge. Not sure if this is true or not, but if it is, did Cadillac screw up?
...
Forum: Suspension / Brakes / Chassis 09-07-2011, 07:03 PM
Replies: 507
Views: 75,054
Posted By 08G8V8
That's what I thought the reason for changing the...

That's what I thought the reason for changing the cross-over tube was, but the explanations given above are talking about maintaining the piston position. Don't see how piston position has changed,...
Forum: Suspension / Brakes / Chassis 09-07-2011, 06:53 PM
Replies: 507
Views: 75,054
Posted By 08G8V8
Here is a photo of a drivers side rear CTS-V on...

Here is a photo of a drivers side rear CTS-V on the left. As you state, the smaller Piston #1 is on the top of the caliper and the cross-over tube is on the bottom of the caliper. As the rotor goes...
Forum: Suspension / Brakes / Chassis 09-05-2011, 11:20 PM
Replies: 507
Views: 75,054
Posted By 08G8V8
I've got the gen1 CTS-V calipers on the front of...

I've got the gen1 CTS-V calipers on the front of my G8. Now that we have a solution for keeping the ebrake, I'm looking to complete the installation with the gen1 CTS-V calipers on the rear.

Both...
Forum: Suspension / Brakes / Chassis 06-25-2011, 11:24 PM
Replies: 12
Views: 1,039
Posted By 08G8V8
Where did you get them, and how much?

Where did you get them, and how much?
Forum: Forced Induction - V8 06-21-2011, 09:53 PM
Replies: 13
Views: 1,416
Posted By 08G8V8
I recently installed a dual set of Aeroforce...

I recently installed a dual set of Aeroforce gauges in a gauge pod on the center dash of my G8. I also have the Aeroforce fuel pressure gauge and boost gauge, both running on 1 of the Aeroforce...
Forum: Forced Induction - V8 06-10-2011, 10:38 PM
Replies: 12
Views: 1,139
Posted By 08G8V8
It's made by Magnuson.

It's made by Magnuson.
Showing results 1 to 30 of 37

 
Forum Jump

All times are GMT -5. The time now is 01:23 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.