Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
PFYC
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums

Showing results 1 to 30 of 500
Search took 0.44 seconds.
Search: Posts Made By: blake-b
Forum: Cosmetics and Lighting Modification Discussions 08-18-2014, 10:59 PM
Replies: 6
Views: 258
Posted By blake-b
I don't know of anywhere you can buy colored ones...

I don't know of anywhere you can buy colored ones but you could have a set powdercoated.
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 08-15-2014, 09:59 PM
Replies: 15
Views: 865
Posted By blake-b
The hobbs switch just activates the second pump...

The hobbs switch just activates the second pump when boost reaches 1-2 lbs of boost (or whatever the switch is for) and deactivates when the engine goes into vacuum.

I would say 1000s, if not...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 08-15-2014, 04:19 AM
Replies: 15
Views: 865
Posted By blake-b
Go Squash and be done with it. If you ever decide...

Go Squash and be done with it. If you ever decide you want to knock on the door of 1000hp, you won't have to change pumps. Virtually all the other pumps (I can think of at the moment) won't do...
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 08-14-2014, 01:32 AM
Replies: 5
Views: 380
Posted By blake-b
Need a different flywheel, zr1 slave and a spacer...

Need a different flywheel, zr1 slave and a spacer for the slave cylinder. The LS9 crank has 9 bolt holes and the LS3 only has 6.

Here is the LS9/ZR1 kit:...
Forum: Forced Induction - V8 08-10-2014, 04:37 AM
Replies: 13
Views: 1,115
Posted By blake-b
I'm sure Ted did it correctly. However I'm...

I'm sure Ted did it correctly. However I'm unfamiliar with SCT so I don't where to tell you to look.
Forum: Forced Induction - V8 08-10-2014, 04:21 AM
Replies: 13
Views: 1,115
Posted By blake-b
Make sure the linear and offsets are entered...

Make sure the linear and offsets are entered correctly in your tune.
zr1 map part # 12592525
Map sensor linear: 312.50 kpa
Map sensor offset: -11.25 kpa
Enter at Engine Diagnostics -> Airflow
...
Forum: Forced Induction - V8 08-10-2014, 03:47 AM
Replies: 13
Views: 1,115
Posted By blake-b
What MAP sensor are you using?

What MAP sensor are you using?
Forum: Forced Induction - V8 08-10-2014, 02:44 AM
Replies: 349
Views: 29,841
Posted By blake-b
You would be in fine hands with an ERL block....

You would be in fine hands with an ERL block. They sponsor the Ohio Boys, Dave (Mighty Mouse) Childress, and others.
Forum: Camaro DIY & HOW-TO instructions & discussions 08-06-2014, 01:54 AM
Replies: 3
Views: 516
Posted By blake-b
You can relocate it anywhere you want. It just...

You can relocate it anywhere you want. It just has to have contact with bare (unpainted) metal. For example, you could make a ground by drilling a hole in the strut tower and putting a bolt and nut...
Forum: Forced Induction - V8 08-02-2014, 06:02 PM
Replies: 20
Views: 1,080
Posted By blake-b
Having had a ysi making over 1k to the wheels and...

Having had a ysi making over 1k to the wheels and having turbos make over 1k to the wheels (in the same car), turbos win, especially for what you want. The ysi pulled like a freight train and the...
Forum: Forced Induction - V8 07-31-2014, 07:26 PM
Replies: 6
Views: 405
Posted By blake-b
I don't drink but I do work for pizza. If our...

I don't drink but I do work for pizza. If our schedules can mesh up I'll certainly come help.
Forum: Forced Induction - V8 07-31-2014, 07:14 PM
Replies: 514
Views: 65,550
Posted By blake-b
If you have facebook you can ask him there, here...

If you have facebook you can ask him there, here is his:
Stangkilr Productions
(https://www.facebook.com/StangkilrProductions)
Forum: Forced Induction - V8 07-31-2014, 07:12 PM
Replies: 6
Views: 405
Posted By blake-b
It won't make any difference. If you have a...

It won't make any difference. If you have a micrometer, do set it at .001 and see how small that is.
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 07-23-2014, 12:39 PM
Replies: 10
Views: 324
Posted By blake-b
I made a bracket for the cooler and it's hung in...

I made a bracket for the cooler and it's hung in front of my intercooler. I used an improved racing oil cooler adapter. It mounts on the block.
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 07-21-2014, 02:13 PM
Replies: 22
Views: 714
Posted By blake-b
My factory one is gone. You can buy a screw in...

My factory one is gone. You can buy a screw in plug that goes in the block. I don't have the part number handy. I am using an improved racing adapter for an after market setrab cooler.
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 07-19-2014, 11:58 PM
Replies: 20
Views: 829
Posted By blake-b
Nope, you are on the money. The cubic inches have...

Nope, you are on the money. The cubic inches have little to do with the suitability of daily driving. The cam will. The cam should be the last part you buy for the engine (technically the pushrods)....
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 07-19-2014, 09:41 PM
Replies: 20
Views: 829
Posted By blake-b
Just for the OP's clarification, It doesn't...

Just for the OP's clarification, It doesn't physically make the sleeve longer, more of the sleeve is used. If the stroke is 4", the piston travels 4" up and 4" within the sleeve of the block.

You...
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 07-19-2014, 09:32 PM
Replies: 7
Views: 245
Posted By blake-b
For some reason I thought you were in Wichita...

For some reason I thought you were in Wichita even though it says "Topeka." I'm sure there are some local trans shops that could loan you a yoke just to see if another will slide in farther.

I...
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 07-19-2014, 06:32 PM
Replies: 7
Views: 245
Posted By blake-b
I understand. Just being facetious. After...

I understand. Just being facetious.

After thinking of your issue, is it possible the driveshaft is just too long? How thick is the coupler?

It might not be comfortable ridewise or noisewise,...
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 07-19-2014, 05:39 PM
Replies: 7
Views: 245
Posted By blake-b
I have nothing constructive to assist you with...

I have nothing constructive to assist you with your transmission problem.

However, the first picture is a yolk. The second is a yoke.

I'm married to an English/writing teacher.
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 07-19-2014, 01:19 PM
Replies: 20
Views: 829
Posted By blake-b
To calculate an engine's size: bore x bore x...

To calculate an engine's size:
bore x bore x stroke x 0.7854 x number of cylinders

As mentioned, stroke is the travel of the piston and bore is the size of the hole it travels in. Both bore and...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 07-18-2014, 04:25 AM
Replies: 4
Views: 263
Posted By blake-b
No loctite on intake manifold bolts. Just follow...

No loctite on intake manifold bolts. Just follow proper torque specs and order.
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 07-17-2014, 08:47 PM
Replies: 4
Views: 322
Posted By blake-b
Contact IdealG on here. He sells modified clutch...

Contact IdealG on here. He sells modified clutch master cylinders and probably knows the info you seek.
Forum: Forced Induction - V8 07-17-2014, 03:40 PM
Replies: 3
Views: 382
Posted By blake-b
I think both gaskets are .051 compressed. LS3...

I think both gaskets are .051 compressed. LS3 gaskets have 5 layers.

NA use LS3 gaskets or LS9 (whichever is cheapest or what you can get)
For FI, use LS9 gaskets
Stock manifold O-rings are...
Forum: Forced Induction - V8 07-17-2014, 03:07 PM
Replies: 2
Views: 282
Posted By blake-b
Here you go...

Here you go (https://www.google.com/search?q=vortech+camaro5.com+site:www.camaro5.com&pws=0&gws_rd=ssl)

And here (http://www.camaro5.com/forums/showthread.php?t=38022)

Plenty to read in those...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 07-15-2014, 03:08 PM
Replies: 7
Views: 309
Posted By blake-b
Nope-you need nothing else. Just put the OEM...

Nope-you need nothing else. Just put the OEM gaskets on and torque them down correctly.
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 07-15-2014, 02:56 PM
Replies: 16
Views: 1,535
Posted By blake-b
You'd be losing about half a point of compression...

You'd be losing about half a point of compression bolting these on so you'd do down to about 10.3 to 1 (assuming your stock chambers are 68cc). An often used rule of thumb is a point of compression...
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 07-15-2014, 10:54 AM
Replies: 16
Views: 1,535
Posted By blake-b
Tuesday bump.

Tuesday bump.
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 07-11-2014, 11:53 PM
Replies: 6
Views: 818
Posted By blake-b
When I had headers, mine rubbed when turning as...

When I had headers, mine rubbed when turning as well. I took the driver's side off, Set a socket on the offending spot, and his the socket with a hammer a few times to dimple it. No more rubbing.
...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 07-11-2014, 02:16 PM
Replies: 10
Views: 439
Posted By blake-b
Personally, I'd cut the hole also. But, if...

Personally, I'd cut the hole also.

But, if you want to drop the cradle, use these instructions:...
Showing results 1 to 30 of 500

 
Forum Jump

All times are GMT -5. The time now is 02:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.