Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
  
TireRack
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums
Reload this Page Search Results
Homepage Garage Wiki Register Social Groups Calendar Search Today's Posts Mark Forums Read


Page 1 of 17 1 234511 Last »
Showing results 1 to 30 of 500
Search took 0.05 seconds. Search: Posts Made By: MA2010SS
Forum: Local Marketplace 09-08-2020, 01:28 PM
Replies: 0
Views: 664
Posted By MA2010SS
Manifolds & Cats

2010 6.2L LS3 right and left manifolds and CATS for sale, less than 2000 miles on them. Located in Swansea MA, asking $325.00 for all

SOLD SOLD SOLD
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 05-17-2018, 05:45 AM
Replies: 4
Views: 994
Posted By MA2010SS
Sounds like the fingers on the PP are not...

Sounds like the fingers on the PP are not releasing the clutch, did you change out the flywheel also? How does the pedal feel?
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 04-03-2018, 05:54 AM
Replies: 2
Views: 1,061
Posted By MA2010SS
They're pre-filled

They're pre-filled
Forum: Forced Induction Discussions 11-22-2017, 06:37 AM
Replies: 5
Views: 1,683
Posted By MA2010SS
A little heat on that crank bolt goes a long way...

A little heat on that crank bolt goes a long way to making that part of the job easier. Looking forward to the end results
Forum: Suspension / Brakes / Chassis 07-19-2017, 06:46 PM
Replies: 14
Views: 2,133
Posted By MA2010SS
Where is the shake?? in the steering wheel or in...

Where is the shake?? in the steering wheel or in the seat??? Front tire sustained visible damage but what about the rear?? Is that damaged on the inside of the wheel?
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 07-14-2017, 05:24 AM
Replies: 17
Views: 9,227
Posted By MA2010SS
mods to the car?? Stock driveshaft, could be...

mods to the car??

Stock driveshaft, could be the carrier bearing while under load
Forum: Forced Induction - V8 07-12-2017, 05:10 AM
Replies: 10
Views: 2,729
Posted By MA2010SS
Sounds like a winner here, my biggest thing is no...

Sounds like a winner here, my biggest thing is no splicing or cutting while keeping the plumbing and wiring looking as factory as possible while what you paid for does the job it's supposed to do
Forum: Forced Induction - V8 07-10-2017, 08:01 PM
Replies: 10
Views: 2,729
Posted By MA2010SS
Should have come from the factory like this on a...

Should have come from the factory like this on a PD blower setup...what's the install like, I do 99% of the work myself when time permits...I'm tired of going to the track a sitting after a run for a...
Forum: Forced Induction - V8 07-10-2017, 07:10 PM
Replies: 10
Views: 2,729
Posted By MA2010SS
Thanks With this kit where does the...

Thanks

With this kit where does the condensate go other than the ground where the track would kick you off for leaking water on the track thanks in advance
Forum: Forced Induction - V8 07-10-2017, 05:49 AM
Replies: 10
Views: 2,729
Posted By MA2010SS
Interchiller

Anyone have experience with or real world results using an interchiller on a PD blower? Looking to get my IAT's down some more and I figure if the factory Demon has one they must be pretty effective.
Forum: Tuning / Diagnostics -- engine and transmission 07-06-2017, 06:31 AM
Replies: 6
Views: 2,783
Posted By MA2010SS
If you have tuner software log the car before the...

If you have tuner software log the car before the install and then log the car after the install, that will tell you the truth. Other than the gear adjustment nothing else is needed in my opinion
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 06-16-2017, 05:13 AM
Replies: 6
Views: 2,089
Posted By MA2010SS
Light pedal, slightly lower engagement, slight...

Light pedal, slightly lower engagement, slight chatter for a few hundred miles were all normal after install. About 75 passes down the strip, light pedal, engagement in the middle of the throw and...
Forum: Camaro ZL1 Forum - ZL1 Specific Topics 05-18-2017, 08:02 AM
Replies: 17
Views: 9,993
Posted By MA2010SS
Easiest way to tell if an engine or any other...

Easiest way to tell if an engine or any other component has been worked on is to see if the marking paint does or doesn't line up anymore. That would mean the bolts have been moved at some point. ...
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 05-17-2017, 02:36 PM
Replies: 3
Views: 868
Posted By MA2010SS
Sounds like the slave cylinder took a dump...I've...

Sounds like the slave cylinder took a dump...I've had real good luck with the RXT twin, light pedal and holds excellent with good street manners.
Forum: Forced Induction - V8 04-25-2017, 08:11 AM
Replies: 16
Views: 3,437
Posted By MA2010SS
Since it's a random misfire and not a specific...

Since it's a random misfire and not a specific cylinder misfire I would suspect the plugs might be the issue or the proper injector data was not uploaded into the tune for the ID 850's
Forum: ZL1 Discussions 04-19-2017, 03:16 PM
Replies: 25
Views: 9,946
Posted By MA2010SS
From the video looks like the system was cat-less...

From the video looks like the system was cat-less also...probably see similar gains or better by just removing the cats and a tune
Forum: Tuning / Diagnostics -- engine and transmission 04-18-2017, 08:12 PM
Replies: 10
Views: 1,902
Posted By MA2010SS
Manual here...I simply like to drive the car and...

Manual here...I simply like to drive the car and not have the car drive me. I do run at the drags and know I would be at least 5 - 7 tenths faster with an auto though.
Forum: Forced Induction - V8 04-12-2017, 06:47 AM
Replies: 10
Views: 2,367
Posted By MA2010SS
Yes, just clock your new pin 180 degrees opposite...

Yes, just clock your new pin 180 degrees opposite of the existing pinned location
Forum: Forced Induction - V8 04-10-2017, 08:03 AM
Replies: 10
Views: 2,367
Posted By MA2010SS
Stock diameter ATI will work best for what you...

Stock diameter ATI will work best for what you are trying to accomplish, that's what I did
Forum: Local Marketplace 03-27-2017, 08:37 AM
Replies: 0
Views: 870
Posted By MA2010SS
Fuel Injectors F/S

Siemens Deka 63 lb/hr fuel injectors

Came off a stock Whipple Camaro kit with about 5K miles on the injectors. Did a cam and upgraded injectors

$300.00, looking for local pick up
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 03-24-2017, 06:13 AM
Replies: 2
Views: 1,172
Posted By MA2010SS
Put the car in 5th gear, e-brake and foot on the...

Put the car in 5th gear, e-brake and foot on the brake and nothing in front of the car while it's running. Slowly release the clutch until the engine starts to bog...if it stalls right away the...
Forum: Forced Induction - V8 03-12-2017, 01:54 PM
Replies: 15
Views: 5,401
Posted By MA2010SS
You're killing me!! :thumbsup:

You're killing me!! :thumbsup:
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 03-10-2017, 10:38 AM
Replies: 7
Views: 1,820
Posted By MA2010SS
ZL1 shafts in my opinion and IF one snapped...

ZL1 shafts in my opinion and IF one snapped replacement is only a couple hundred
Forum: Forced Induction - V8 03-10-2017, 06:22 AM
Replies: 195
Views: 89,173
Posted By MA2010SS
Good luck with the build, it's going to be fun...

Good luck with the build, it's going to be fun once it's done
Forum: Forced Induction - V8 03-09-2017, 09:01 PM
Replies: 15
Views: 5,401
Posted By MA2010SS
Yes it peaked at the end of the pulls at 11.19...

Yes it peaked at the end of the pulls at 11.19 PSI...it's about as much as I want to go with the ZL1 pump and now 80lb injectors
Forum: Forced Induction - V8 03-09-2017, 07:20 AM
Replies: 15
Views: 5,401
Posted By MA2010SS
I'm into the sleeper look / sound so this cam was...

I'm into the sleeper look / sound so this cam was perfect, not noticeable and really have to listen to hear it, but makes really good power
Forum: Forced Induction - V8 03-08-2017, 12:57 PM
Replies: 15
Views: 5,401
Posted By MA2010SS
I'm just waiting for the weather to get warmer up...

I'm just waiting for the weather to get warmer up here to really test it out...roads are cold and literally feel like you are on ice right now without getting into that GO pedal :thumb:
Forum: Forced Induction - V8 03-07-2017, 06:33 AM
Replies: 15
Views: 5,401
Posted By MA2010SS
BTR PDS Stage 1 shouldn't disappoint at all. If...

BTR PDS Stage 1 shouldn't disappoint at all. If I didn't have a stock bottom end on this engine I would have had the rev limiter raised to 7K and at that point might have found peak horsepower
Forum: Forced Induction - V8 03-07-2017, 06:31 AM
Replies: 15
Views: 5,401
Posted By MA2010SS
Thank you...the car feels lighter if that makes...

Thank you...the car feels lighter if that makes any sense, and with the whipple in stock form it already felt light to begin with
Forum: Forced Induction - V8 03-06-2017, 12:35 PM
Replies: 15
Views: 5,401
Posted By MA2010SS
BTR PDS stage 2 results

Normally I do all the work on my own car but not having anytime to do work on it kind of sucks. I let the guys from Slowhawk Performance take care of this one for me. Talked to Don about what I was...
Showing results 1 to 30 of 500
Page 1 of 17 1 234511 Last »

 
Forum Jump

All times are GMT -5. The time now is 11:18 PM.

Contact Us - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com - Archive - Privacy Statement - Terms of Service / DMCA Policy - Top

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.