Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
The Bracketeer
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums


Showing results 1 to 30 of 97
Search took 0.02 seconds.
Search: Posts Made By: Inferno1LE
Forum: Camaro DIY & HOW-TO instructions & discussions 06-10-2015, 11:43 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
The red wire needs to be in the middle of the...

The red wire needs to be in the middle of the switch, the other 2 wires don't matter. The relay needs to be installed with the wire on top. You need to ground the black wire on the ground bolt next...
Forum: Camaro DIY & HOW-TO instructions & discussions 05-21-2015, 07:38 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
If you're NPP that was put on the car afterwards...

If you're NPP that was put on the car afterwards uses the factory wiring, and opens and closes like it does from the factory (I.E. It is open at idle, then closes until you reach 3500rpms, then opens...
Forum: Camaro DIY & HOW-TO instructions & discussions 03-21-2015, 01:17 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
I understand what you are referring to; however I...

I understand what you are referring to; however I think you are misunderstanding the concept. If you measure the voltage at the switch on the pin that is tied to the coil on the relay, you will see...
Forum: Camaro DIY & HOW-TO instructions & discussions 03-21-2015, 11:26 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
This is completely untrue. There is no 12v at the...

This is completely untrue. There is no 12v at the switch. The switch throws a ground, as does the factory trigger. There is +12V IGN on the other side of the coil at the relay as there is in the...
Forum: Camaro DIY & HOW-TO instructions & discussions 03-21-2015, 09:28 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
I just want to clarify something... It was...

I just want to clarify something... It was brought to my attention recently that there is some confusion as to how the switch powers the NPP flaps in my drawing or the plug and play kit. To clarify,...
Forum: Camaro DIY & HOW-TO instructions & discussions 03-18-2015, 06:39 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
You'd have to Dyno the car both ways to know for...

You'd have to Dyno the car both ways to know for sure.
Forum: Suspension / Chassis / Brakes 03-17-2015, 10:30 PM
Replies: 48
Views: 4,808
Posted By Inferno1LE
Can you get replacement rotor rings for these...

Can you get replacement rotor rings for these when the time comes, or do you need to buy a whole new rotor?
Forum: Camaro DIY & HOW-TO instructions & discussions 03-16-2015, 09:44 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
That's great, I'm glad to hear it!

That's great, I'm glad to hear it!
Forum: Camaro DIY & HOW-TO instructions & discussions 03-16-2015, 10:57 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
If you open up the actual relay, you will see...

If you open up the actual relay, you will see that's not possible.
Forum: Camaro DIY & HOW-TO instructions & discussions 03-15-2015, 05:42 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
It is completely plug and play... Remove the...

It is completely plug and play... Remove the factory relay and plug in the one I give you. The hardest part of the install is deciding where to drill a hole for the switch. PM me if you're interested.
Forum: Camaro DIY & HOW-TO instructions & discussions 03-15-2015, 05:38 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
The despiking resistor is present in the factory...

The despiking resistor is present in the factory relay, so if you're wiring it via the diagram, and cutting the lt blue / yellow wire, you have nothing to worry about. The problem is that if you are...
Forum: Camaro DIY & HOW-TO instructions & discussions 03-12-2015, 10:37 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
If you take apart a relay, you should be able to...

If you take apart a relay, you should be able to figure it out.
Forum: Camaro DIY & HOW-TO instructions & discussions 03-12-2015, 09:36 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
That's right, and moving the de-spiking resistor...

That's right, and moving the de-spiking resistor in the relay so the fuel pump circuit is still protected after the switch is installed.
Forum: Camaro DIY & HOW-TO instructions & discussions 03-11-2015, 11:33 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
Just thought I'd let everybody know... I made a...

Just thought I'd let everybody know... I made a few more of the plug n play kits, so if anyone is interested, let me know.
Forum: Camaro DIY & HOW-TO instructions & discussions 02-24-2015, 06:10 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
No I don't think so. I wonder if a custom exhaust...

No I don't think so. I wonder if a custom exhaust shop could take apart the NPP muffler and weld a cat inside it.
Forum: Camaro DIY & HOW-TO instructions & discussions 02-04-2015, 11:01 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
I actually just sold my last one. If you're...

I actually just sold my last one. If you're interested, PM me. I can make some more, I just have to get the parts.
Forum: Transmission / Driveline 10-24-2014, 08:28 PM
Replies: 3
Views: 514
Posted By Inferno1LE
SOLD...

SOLD...
Forum: Transmission / Driveline 10-24-2014, 01:04 PM
Replies: 3
Views: 514
Posted By Inferno1LE
Ideal Garage Master Cylinder

SOLD - Used Ideal Garage Master Cylinder for V8 Camaros. I'm upgrading my clutch and am putting the stock one back in. Nothing wrong with it, and it works very well with the stock clutch, just not...
Forum: Transmission / Driveline 10-11-2014, 12:41 PM
Replies: 0
Views: 280
Posted By Inferno1LE
WTB: Tick Clutch Line

Anyone have a tick braided clutch line? Not the bleeder line, but the line from the master to trans.
Forum: V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 10-02-2014, 09:27 AM
Replies: 11
Views: 2,165
Posted By Inferno1LE
Any update on your Mantic 9000? I'm considering...

Any update on your Mantic 9000? I'm considering getting one and want to see how it's working out for you.
Forum: Camaro DIY & HOW-TO instructions & discussions 09-24-2014, 03:57 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
If you're interested, I have a few more of my...

If you're interested, I have a few more of my plug and play kits available. Just plug in a new relay to replace the original, and install a switch... It's that simple. No cutting wires or additional...
Forum: Wheels / Tires 09-07-2014, 10:42 PM
Replies: 13
Views: 1,741
Posted By Inferno1LE
Payment sent

Payment sent
Forum: Road Course/Track and Autocross 08-22-2014, 07:38 PM
Replies: 220
Views: 14,618
Posted By Inferno1LE
Here's a few laps from my first day at NJMP...

Here's a few laps from my first day at NJMP thunderbolt earlier this year. At Track Time 4 Cars we run it with the chicane. My slicks corded earlier that day, so these are on the stock Goodyears (I...
Forum: Camaro DIY & HOW-TO instructions & discussions 08-09-2014, 11:29 AM
Replies: 122
Views: 14,583
Posted By Inferno1LE
You run it up the door sill past the kick panel,...

You run it up the door sill past the kick panel, then under the carpet to the driver side and back down the center console. Call me if you need help.
Forum: Camaro DIY & HOW-TO instructions & discussions 08-08-2014, 01:43 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
Glad to hear it's working properly. The flaps...

Glad to hear it's working properly. The flaps close as soon as you turn the key on with the switch in the closed position. However, this is only true if there is vacuum in the tiny reserve canister...
Forum: Camaro DIY & HOW-TO instructions & discussions 07-09-2014, 03:44 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
Thanks, I'm glad it's working out for you. ...

Thanks, I'm glad it's working out for you.

You know when you have some time during the day to spend on it it's not that bad. At 1:00am when I got done with work, it just seemed more complicated.
Forum: Camaro DIY & HOW-TO instructions & discussions 07-07-2014, 10:16 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
I wish I thought of that. Looks great!

I wish I thought of that. Looks great!
Forum: Camaro DIY & HOW-TO instructions & discussions 07-07-2014, 07:03 PM
Replies: 122
Views: 14,583
Posted By Inferno1LE
I had some time last weekend and I made 2 more of...

I had some time last weekend and I made 2 more of the plug and play kits. If anyone is interested, I have them ready to ship.

I also am working on a wireless kit. At the moment, it doesn't work...
Forum: Suspension / Brakes / Chassis 06-26-2014, 08:44 PM
Replies: 22
Views: 2,365
Posted By Inferno1LE
Most of the good brake pads make a lot of dust....

Most of the good brake pads make a lot of dust. The stock pads made a lot of dust from what I remember. I have never used the red stuff, but I would probably call EBC and ask what they recommend for...
Forum: Suspension / Brakes / Chassis 06-26-2014, 07:58 PM
Replies: 22
Views: 2,365
Posted By Inferno1LE
Same pads... Ferodo HP1000 I think. I like Amsoil...

Same pads... Ferodo HP1000 I think. I like Amsoil Series 600 DOT4, but any of the fluids around the 600 degree dry boiling point will work well.
Showing results 1 to 30 of 97

 
Forum Jump

All times are GMT -5. The time now is 06:39 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2015, vBulletin Solutions, Inc.