[thahemp]

This is a pretty straight-forward installation. Make sure you bite the bullet, and get the right tools for the job before you start. You'll thank yourself later. I spent less than $60 at Autozone getting ready for the install. $25 of that was a deposit for the O2 sensor socket.

Pictured here are the parts to be installed.

• Midpipes with high flow cats
• Solo midpipe to manifold gaskets
• O2 sensor extenders (already installed in the rear bungs)
• bolts with 2 flat washers, 1 lock washer, and 1 nut each

I measured the depth to the rear manifold bolts before I went to buy my tools. Nothing sucks more than struggling to get a wrench on something. I wanted to be sure that I could clear the top of the engine with my breaker bar. The rear bolt is also at a slightly tilted angle, so a swivel joint is recommended.




List of tools used

• 24" 1/2" drive breaker bar
• 3/8" drive ratchet
• 24" extension
• 1/2" to 3/8" drive coupler
• 3/8" swivel joint
• 15mm socket
• 15mm open face wrench
• O2 socket tool
• needlenose pliers
• PB Blaster (thread loosening spray)
• anti-seize
• beer

Ready to get started!

1. Preparation
   Jack the front of the car up and place your jack stands. The higher off the ground you can get the front end, the better. You definitely want room to work comfortably while under the car. Don't forget to pull your parking brake before you start lifting the front end.
   
   
   
2. Spray rear O2 sensor threads with PB blaster
   There's no reason to spray the sensor bodies. I don't know if it will cause a problem, but try to avoid it. I didn't even try to spray the front O2 sensors. It would have taken some serious marksmanship. If you're doing these first 3 steps while the exhaust is still hot... be careful!
   
3. Break the rear O2 sensors loose
   Put the O2 sensor socket on your breaker bar and carefully slide it onto the rear O2 sensor. The wires should exit the socket through the slit in the side. Carefully apply pressure until the sensor threads break loose. Stop as soon as it breaks free. You'll finish taking them out later. Don't put more than about a half turn on them with the O2 socket. You'll twist up the wires and possibly ruin them.
   
4. Let the car finish cooling!
   Grab a beer. It needs to sit for a couple hours at least.
   
5. Disconnect all 4 O2 sensor harnesses
   Note the way the O2 wire harness is routed on the rear passenger side in the pic above. There is another pic below that shows it a little better. I used needlenose pliers to pinch the locking insert on the rear connectors. Pinch it, pull the lock out, and then pull on the connector from the tab side to disconnect it. Disconnect both rears then move to the front. Do the driver's side first because it will help you understand what you're dealing with on the front O2 connectors. They are the same on both sides, but they aren't mirrored, so the green lock is actually behind the engine on the passenger side. From the top of the car looking down: Support the connector itself and pull on the green locking tab until it comes out. Pull the tab side of the connector (firewall side) towards the floor. It should pop right out. Repeat for the passenger side now that you know what you're dealing with.
   
   
   
   
   
   
   
   
6. Unbolt the stock midpipes from the manifold
   From the top of the car, using a 15mm socket, swivel joint, and long extension, carefully break both bolts loose on both sides of the car. Try not to touch any of the engine electronics while you're in there. Disconnecting the battery probably wouldn't be a terrible idea . Once they're loose, switch the breaker bar out for a standard ratchet and finish removing the bolts. I slid back under the car and reached up from the bottom to get the bolts off of the ends of the studs.
   
   
   
7. Break the midpipe/manifold connection
   Push/pull on the midpipe from under the car until both sides come loose from the manifolds. The passenger side took a little effort for me. Just be patient and don't go crazy. Once they both come free, the cat-back section of the exhaust will rest on the cross brace.
   
   
   
8. Make sure all of the O2 wire harnesses are clear of the vehicle
   You don't want any of the wire harnesses getting hung up when you pull the stock midpipes off the car. I just pulled all the wires down so they were hanging off of the pipes.
   
   
   
9. Loosen the band clamps at the rear of each midpipe
   I used the breaker bar again here... probably wasn't necessary, but it made it easy. I loosened both bolts on both sides until I could "walk" the midpipes out of the front of the band clamps. There is plenty of clearance in the engine bay for the procedure.
   
   
   
10. Move the O2 sensors to their new home
    The O2 extenders should be screwed into the rear bungs on both of the Solo midpipes at this point. Mine looked like they had red thread locker on them. I probably wouldn't have done that if I had been the one to install them. I likely would have just anti-seized them like I did to the rest of the connections. Move the O2 sensors from old to new one at a time. Don't get them mixed up. They should go to the exact same spot on the new midpipe. Once they break free, you should be able to remove them by hand. Put a little anti-seize on the threads and screw it into the new midpipe. Move both of the rear sensors first, because you're gonna have to get a little rough with the front ones.
    
    Put the O2 socket back on the breaker bar for the fronts and position the midpipe so that you are pushing the breaker bar towards the floor. Pulling up makes it almost impossible to keep the pipe from rotating when you pull. I just stood on the cat while pushing and broke them free pretty easily. Move the front sensors just like you already did the rears. Don't forget the anti-seize. Tighten all 4 sensors before you install the Solo midpipes.
    
    
    
    
    
    Good bye ugly.
    
    
11. Bolt the Solo midpipes to the manifold
    This can be a little tricky for one person. If you're doing this by yourself, try clamping vice grips on the bolt heads from the bottom of the car. Then move to the top and start cranking. If you get it clamped right it will work.
    
    I had a little trouble with the Solo gaskets on my car. I'm not sure that they fit a 2012 properly. I'll probably end up getting some different gaskets and redoing this part. Anyways... From the bottom of the car the sequence is: bolt -> flat washer -> Solo flange -> gasket -> manifold flange -> flat washer -> lock washer -> nut. The rear O2 sensor should be angled toward the center of the car. If it's not, you're on the wrong side. Do the rear bolt first. That will make the front bolt a lot easier. Once you get everything lined up, tighten the bolts down from the top side of the car. You may have to slide the rear of the midpipe into the loose band clamps to get it positioned where you want it before tightening down the front bolts. My passenger side didn't quite reach the band clamp, but driver side did. No big deal.
    
12. Put the Solo midpipes into the band clamps
    You may have to adjust the position of the band clamps on the cat-back side of the exhaust. I had to slide the clamp towards the engine a little bit on the passenger side. You just need to get an inch or so worth of midpipe into the front of the band clamp. Once you're happy with the alignment of everything, tighten the band clamps back down.
    
13. Reconnect the O2 sensors
    I routed the rear passenger side O2 harness just like it was before I pulled it out. The driver side is just a straight shot to the connector. Push the wire bundles for the front O2 connectors up from underneath the car. They'll stay where you put them. Go back to the top side of the car and reconnect them just like you took them apart. It's up to you whether you want to mess with the locking tabs for the 4 connectors. I didn't bother putting them back in. The connectors are already positive latch.. I don't understand the reasoning for the locking mechanisms.
    
14. Done! I would advise more beer here.