View Single Post
Old 12-12-2012, 12:47 PM   #1
HubStep
 
HubStep's Avatar
 
Drives: 2010 Victory Red 2SS
Join Date: May 2012
Location: Atlanta
Posts: 433
HubStep Victory Red SS

IMPORTANT: All these images/videos seem to crash the latest firefox, and I have a fast machine. Idk why. Safari/Chrome seem to work great. Haven't tried the latest IE. Just don't use FF :( Also use COMMAND - or CONTROL - to zoom the page out, makes viewing it all easier

Hey guys, moving my poorly-placed build thread here! How I plan to organize it:

[First post] = Videos {New->Old}

[All subsequent posts] = Picture Block # {Old -> New}

So Basically all the latest videos will be at the top of this thread forever, and I'll add clusters of photos down the thread as I go

Hope you all enjoy!!!!!



Mods List
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>



-RS headlights (ofer's the man!) w/AAC color shift 2.0 halos 6k xenon temp (installed myself)
-AAC's xenon projector fogs painted black with color shift halos as well 8k (by mistake, getting 6 later)
-Wired high-beam to trip the fog's relay for maximum output on high beam!
-LED white/amber turn signal inserts. White mode is switchable (closest switch on center console), amber is independent. Basically the blinker still works but white is on/off.
-RGB foot well lighting w/dimmer on center console
-AAC dynamic mail slot scanner w/power interrupt switch on center console (1st rocker switch)
-AAC color shift chevy bow tie
-AAC "concept" side markers, both front/back blink sequentially with the car's main blinkers!
-AAC drop-in replacement license plate LEDs
-AAC high intensity reverse light LEDs.
-Muffler "trash-cans" cut off.
-Technostalgia Tail lights, timed relay circuit has red rear side markers blink in-sequence with turn signal animation
-18% ceramic tint side/back (windshield 50% soon)
-Rider graphix flat-black "hockey sticks" w/lower piece
-Center speaker removed (really helps!)
-illuminated cup holders + chrome billet cup holder plate
-RGB wrap-around door trim + dash trim kit from sjmautoprod and ofer, LEDs from oznium.
-RGB wheel light kid from weedahoe
-Red calipers from Mike the Powdercoater
-MTI stainless red racing brake lines
-HAWK ceramic pads front/rear
-Drilled/slotted rotors front/back
-DOT4 brake fluid
-Dual-channel lighting setup



>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>


VIDEOS
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
Best/Most Recent video: Winter 2012 Update


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
Fall 2012 update


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
Summer 2012 Update *this was shot before the cup holder mod*


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
Illuminated Cup holders video


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
Technostalgia tail lights + Rear AAC side marker. I got the marker to blink in-sync with the tech's turning animation!


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
Relay setup making the AAC LED side markers blink sequentially with the front blinker!


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
Technostalgia tail lights installed! This video shows sequential turn/rapid fire/hazard mode


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
RGB foot well lighting


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
Cutting bumper for fogs! Yikes!


>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
Color shift chevy bow tie.




>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>



BLINKING SIDE MARKERS
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

Several People have asked how I managed to get the side markers to blink:

I got an 8 pin relay from Fry's that was set up like this:

1 2 -signal lead
3 4x
5 6x
7 8x

x=unused

Pins 1 and 2 were the trigger, so I wired it up to the blinker (the turn signal bulb has 3 wires, GND, Blinker, and Running)

Now with this relay in the "off" position (no pulse on the blinker) pins 5&7 form a pass-through. So anything plugged into 5 will come out 7 or vice-versa. When the blinker fires it trips the relay to switch so pins 5&3 are connected instead of 5 and 7. I wired the side marker V+ wire into pin 5 and out pin 7 so when the blinker is off everything is normal. When the blinker fires it trips the relay interrupting the power to the side marker, all done! Pins 6&8 do the same thing to 6&4, but I had no need for it.

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>

Last edited by HubStep; 12-12-2012 at 04:26 PM.
HubStep is offline   Reply With Quote