Thread: 98 Camaro 427ci
View Single Post
Old 02-12-2010, 03:51 PM   #1
gofast908z
 
gofast908z's Avatar
 
Drives: Camaro
Join Date: Apr 2009
Location: California
Posts: 400
98 Camaro 427ci

Would rather not go into why I’m selling, but I'm listing the Camaro for sale. If I don’t get the price I want, then I wont sell. I have the title in hand, ready to sell.

1998 Camaro Z28

Motor:
-Factory new LS3 block
-427ci, 12:1 CR, bored/stroked/balanced/blueprinted
-Forged Compstar 4.1" crank
-Forged Compstar rods
-Custom Wiseco forged pistons
-ARP studs
-TSP ported L92 heads
-L76 intake manifold (paint matched to car)
-TSP 251/259 on 111 lsa .661 lift
-Kooks 1 7/8 LTs
-Nick Williams 90mm throttle body
-42# injectors
-Walbro 255lph fuel pump with custom access panel
-3" true duals with Dr. Gas X-pipe and magnaflow mufflers
-Dual DMH low-profile e-cutouts
-Fast Toys 85mm lid
-SLP CIA duct
-ZO6 MAF
-Optima Red Top
-Abear Motorsports polished valve covers (coil packs sit inside)



Drivetrain:
-D&D built T56
-Spec 3 clutch and billet flywheel
-WS6 store short stick
-Hurst classic white 6-speed shift ball
-3.42 gears




Suspension/Braking
-BMR tubular K-member
-BMR upper and lower tubular A-arms (adjustable)
-Strano revalved Bilstiens
-BMR 1" springs
-BMR boxed subrames
-BMR adj torque arm
-BMR adj LCAs
-BMR Xtreme STB (powdercoated black)
-BMR adj PHB
-Trac Tek relocation brackets
-Wolfe 6-point roll bar with door swingouts.
-Stroud 5-point safety harnesses
-Powerstop crossdrilled rotors
-Hawk Ceramic brake pads
-Earl’s Stainless Steel brake lines
-ARP 3.25” lengthened wheel studs for track use (all 4 corners)


Interior
-Brand new carpet from Stock Interiors
-Raamat sound deadening throughout entire car
-Retained stock seatbelts with racing harnesses
-Rear seat delete
-Pioneer DEH-P6050
-Alpine 6 ” speakers in middle panels
-Interior trim pieces professionally sanded and painted to match factory ext
-Custom TA seats, repadded, genuine leather, real suede inserts, heaters, headrest embroidery
-Brand new GM seatbelts
-Emblem Pros ashtray switch plate for cutouts and line lock



Exterior
-SLP Ultra Z Ram Air hood
-RK Sport smooth grill with mesh behind
-Halo headlights (chrome)
-Brand new clear corners
-Custom stainless 427 badges (in Z28 font) by Emblem Pros
-Stainless CAMARO inserts on rear panel by Emblem Pros
-Chrome SS 10spokes
-rear 10spokes custom widened by Weldcraft to 17x11
-custom spacers for unique offset
-275’s up front, 315’s out back
-Paint is swirl and scratch free




Mileage:
-Body 160k
-rear 80k
-motor 4k
-trans 2k







Those that know me and have seen my car know that I take exceptional care of it. This isn’t some quickly thrown together project either… only the best parts have been used and the car runs amazing. Its pretty much a full track car ready to run 10’s, just needs a rear (nothing wrong with stock one though). Tune will be finished shortly, but it’s a serious car. Put down 521rwhp and 473rwtq on the dyno.

I am in no hurry to sell, so if I don’t get the price I want I will keep it.

I have over $25k into actual mods on the car.

Asking $16k fairly firm on price



Pics





























(before new lid and maf)



















Last edited by gofast908z; 05-02-2010 at 10:51 PM.
gofast908z is offline   Reply With Quote