Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
RDP Motorsport
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Technical Camaro Topics > Camaro DIY & HOW-TO instructions & discussions

Camaro DIY & HOW-TO instructions & discussions All DIY projects & discussions

Reply
 
Thread Tools
Old 10-10-2009, 01:28 PM   #1
Li0nel1234
What should I name my car
 
Li0nel1234's Avatar
 
Drives: 2010 Camaro 2SS RS IOM
Join Date: Jul 2009
Location: San Antonio, TX
Posts: 770
Send a message via AIM to Li0nel1234
DIY: GFX Outlets add Wire Mesh and Paint, Muffler Delete

Hey this is my first DIY write up so give me a little slack.
Before Pics
Name:  before.jpg
Views: 2071
Size:  159.6 KB
Name:  before2.jpg
Views: 2297
Size:  140.8 KB

Items Necessary:
lift
something to cut off your muffler (a saw will work if you don't have anything fancy)
Muffler Dump tips
Welder
The wire mesh you want
Cardboard
Sharpie (marker that works on paint)
Tin snips/shears (big heavy duty sicissors)
Rough, medium and fine sand paper
Flat black rust proof paint (anycolor you want actually)
Weird Screw head and driver (see below picture)
Ratchet, and ratchet adapter to accept the weird screw head.
Plyers (something to grab and hold still the little screw piece while you screw it in)

Step 1: Delete your mufflers (this is simple enough to do yourself but you can pay a muffler shop and they'd do it for around 40 usd... don't pay more than that)
Cut and remove, Not difficult but I'd have someone there to help you hold it up while you cut.
Each one weighs about 18 lbs so that's 36lbs of weight loss.
Here's where to make the cuts (you can go closer to the cats if you want but I did it here to keep it simple:
Name:  cut here.jpg
Views: 1895
Size:  142.3 KB
Name:  cutoff.jpg
Views: 1913
Size:  132.2 KB

Step 2: weld on some dump tips
Name:  dumped.jpg
Views: 1901
Size:  144.5 KB

Step 3: remove your outlets using one of these screw heads on the 4 screws located on the outlets. (I don't know what the screw head is called someone help me out here)
Name:  tool.jpg
Views: 1966
Size:  119.7 KB
Name:  screws.jpg
Views: 1888
Size:  118.3 KB

Step 4: Lay down your outlet on the cardboard and trace the inside opening for your cardboard template. Cut it out and place inside to see if it fits, you will more than likely have to trim certain spots to get it to fit. Also, the same template might not work for both so you should one for each outlet. They will be pretty close though.
Name:  cardboard.jpg
Views: 1891
Size:  139.7 KB

Step 5: Trace the outline of your template on the wire mesh and then cut out with your tinsnips and sand the edges down with the rough grit till they fit flush inside your outlets. (NOTE: This is probably the most difficult part of this project, you have to insert it at an angle then lay it flat and figure out which points aren't letting you press it down all the way then remove and sand down those points. I used the sharpie again to make marks where these pressure points were so I could sand those spots a little extra till it fit nice and snug) When you have the mesh inserts fitting nicely, sand the front and back faces with the medium grit sand paper
Name:  trace.jpg
Views: 1892
Size:  163.7 KB

Step 6: Sand the Outlets (only where it will be visable on the GFX with medium then fine grit sand paper. (unless you don't want to paint them then skip this step).

(NOTE if you don't want to paint your outlets or inserts you will have to tape off your outlets where it will be visable with lots of masking tape or painters tape due to the specks of liquid metal from making the welds before doing the next step. OR you could do apoxy or JB weld, I wouldn't do that though)

Step 7: Weld mesh inserts in place then sand off any of the metal specs with the medium sand paper followed by the fine grit (if it's a big speck you can poke it off with a flat head and a hammer then sand)

Step 8: Paint, allow to dry, paint, and allow to dry (repeat till you feel good about it, 4 for me)
Name:  paint.jpg
Views: 1902
Size:  127.0 KB

Step 9: Install outlets back on your GFX. This can be done from a driveway but your neck will be sore the next day (I did). Use your weird screw head tool and your plyers. (Note this part can be a little tricky since now you have wire mesh in the outlet the top screw to the outlet is a little harder to reach. I slid the weird screw tool through the wire mesh and ratcheted it in. If you make some scratches on your wire mesh you can just make some touchups with a q-tip and your paint)
Name:  tool.jpg
Views: 1966
Size:  119.7 KB

Enjoy the awesome new look of your GFX (these pics were done b4 I did the touchups so you can see where I slid the weird tool in there)
Name:  left.jpg
Views: 1858
Size:  114.9 KB
Name:  right.jpg
Views: 1865
Size:  124.7 KB
Name:  both.jpg
Views: 1877
Size:  143.4 KB

This took me about about 4 hours worth of work prior to painting. Then about another half our to reinstall and 2 minutes to do the touchup.

I hope this helps... PM me with any questions. I'd be glad to help you out.
Attached Images
     
__________________
Performance: ARH 2"/"3 headers + ARH 3" HF catback system, SS brake lines, hawk HP+ pads, motul RBF 600 fluid, K&N CAI (w/custom insulation), plug wires, air scoop, Hurst STS, Pedders Track II suspension, 18x10 wheels, 295/45/18 Nitto NT05s
Looks: powder coated iom calipers, LED foglights w/ always on harness, custom painted bowties, window tint, smoke tinted tail lights etc, oem gfx w/ custom outlets, painted taillight bezels, all weather trunk mat
Li0nel1234 is offline   Reply With Quote
Old 10-28-2009, 03:02 PM   #2
yubman
 
Drives: paid for
Join Date: Sep 2009
Location: USA
Posts: 42
Looks good. Always thought the tips inside the ground effects looked kind of redundant.

Without mufflers at all, your car must be very loud.
yubman is offline   Reply With Quote
Old 10-28-2009, 03:15 PM   #3
5th_GEN_SS
Junkie
 
5th_GEN_SS's Avatar
 
Drives: SIM 2SS/RS M6
Join Date: Sep 2008
Location: Cleveland, Ohio
Posts: 1,621
hmm interesting
__________________
"Letty" Murdered out 2013 Camaro 1LE. (Old car SIM 2010 2SS/RS)
5th_GEN_SS is offline   Reply With Quote
Old 10-28-2009, 04:06 PM   #4
CamaroSkooter
Retarded One-Legged Owl
 
CamaroSkooter's Avatar
 
Drives: 2010 Black Camaro 2SS
Join Date: Oct 2008
Location: San Antonio, TX
Posts: 9,682
I didn't know you were just running turn-downs. Nice setup
CamaroSkooter is online now   Reply With Quote
Old 10-28-2009, 05:28 PM   #5
5thGen
 
Drives: Black 2LT/RS, jeep Wrangler
Join Date: Aug 2009
Location: NJ
Posts: 125
cool, not on your car ..
5thGen is offline   Reply With Quote
Old 10-29-2009, 01:06 PM   #6
Demon Hunter
 
Demon Hunter's Avatar
 
Drives: 2010 Black Camaro LT
Join Date: Oct 2009
Location: So Cal
Posts: 676
Any one know how legal this really is. I'd imagine it's pretty freakin' load. I'd assume that'd get you in trouble in most states. I'd do it if I knew I could get away with it in California.
Demon Hunter is offline   Reply With Quote
Old 10-29-2009, 01:11 PM   #7
Camaro509

 
Camaro509's Avatar
 
Drives: 2010 2SS/RS Black
Join Date: Mar 2009
Location: Kansas
Posts: 1,087
Quote:
Originally Posted by Demon Hunter View Post
Any one know how legal this really is. I'd imagine it's pretty freakin' load. I'd assume that'd get you in trouble in most states. I'd do it if I knew I could get away with it in California.

It isn't that loud at all. Had this done to mine as well, cept straight pipes and factory tips reinstalled. It is of course louder without the mufflers, but it isn't so loud I'll get tickets for it.

Really like that mesh-look without the tips showing through.

Oh yea, that is called a Torx drive.
__________________
Understeer, Oversteer, Wheel Alignment (Camber etc), Torque, Horsepower, Camaro

Fold for team 11108 to help find a cure!
Folding@home Stanford's Research DC Program.
Camaro509 is offline   Reply With Quote
Old 10-29-2009, 01:13 PM   #8
GTAHVIT
One Lucky Guy.
 
GTAHVIT's Avatar
 
Drives: #22 Tom Henry Racing 2010 2SS/RS
Join Date: Dec 2007
Location: Saint Augustine FL
Posts: 28,765
Quote:
Originally Posted by Demon Hunter View Post
Any one know how legal this really is. I'd imagine it's pretty freakin' load. I'd assume that'd get you in trouble in most states. I'd do it if I knew I could get away with it in California.
You can't get away with this in CA... Nor any state that has emmisions inspections....


But in FL.....
GTAHVIT is offline   Reply With Quote
Old 10-29-2009, 04:09 PM   #9
5thGen
 
Drives: Black 2LT/RS, jeep Wrangler
Join Date: Aug 2009
Location: NJ
Posts: 125
Quote:
Originally Posted by GTAHVIT View Post
You can't get away with this in CA... Nor any state that has emmisions inspections....


But in FL.....
bs . i rented a shelby in florida and got a ticket in a residential area cause the cops assumed we were going over 20 it was all the sound
5thGen is offline   Reply With Quote
Old 10-29-2009, 04:19 PM   #10
Li0nel1234
What should I name my car
 
Li0nel1234's Avatar
 
Drives: 2010 Camaro 2SS RS IOM
Join Date: Jul 2009
Location: San Antonio, TX
Posts: 770
Send a message via AIM to Li0nel1234
Quote:
Originally Posted by 5thGen View Post
cool, not on your car ..
? what does that mean?
__________________
Performance: ARH 2"/"3 headers + ARH 3" HF catback system, SS brake lines, hawk HP+ pads, motul RBF 600 fluid, K&N CAI (w/custom insulation), plug wires, air scoop, Hurst STS, Pedders Track II suspension, 18x10 wheels, 295/45/18 Nitto NT05s
Looks: powder coated iom calipers, LED foglights w/ always on harness, custom painted bowties, window tint, smoke tinted tail lights etc, oem gfx w/ custom outlets, painted taillight bezels, all weather trunk mat
Li0nel1234 is offline   Reply With Quote
Old 10-29-2009, 04:19 PM   #11
Li0nel1234
What should I name my car
 
Li0nel1234's Avatar
 
Drives: 2010 Camaro 2SS RS IOM
Join Date: Jul 2009
Location: San Antonio, TX
Posts: 770
Send a message via AIM to Li0nel1234
Quote:
Originally Posted by Demon Hunter View Post
Any one know how legal this really is. I'd imagine it's pretty freakin' load. I'd assume that'd get you in trouble in most states. I'd do it if I knew I could get away with it in California.
It's legal here. As long as u don't remove the cats.
__________________
Performance: ARH 2"/"3 headers + ARH 3" HF catback system, SS brake lines, hawk HP+ pads, motul RBF 600 fluid, K&N CAI (w/custom insulation), plug wires, air scoop, Hurst STS, Pedders Track II suspension, 18x10 wheels, 295/45/18 Nitto NT05s
Looks: powder coated iom calipers, LED foglights w/ always on harness, custom painted bowties, window tint, smoke tinted tail lights etc, oem gfx w/ custom outlets, painted taillight bezels, all weather trunk mat
Li0nel1234 is offline   Reply With Quote
Old 10-29-2009, 04:46 PM   #12
GTAHVIT
One Lucky Guy.
 
GTAHVIT's Avatar
 
Drives: #22 Tom Henry Racing 2010 2SS/RS
Join Date: Dec 2007
Location: Saint Augustine FL
Posts: 28,765
Quote:
Originally Posted by 5thGen View Post
bs . i rented a shelby in florida and got a ticket in a residential area cause the cops assumed we were going over 20 it was all the sound
you got a speeding ticket not a smog law ticket...
GTAHVIT is offline   Reply With Quote
Old 11-07-2009, 09:03 PM   #13
qbert48

 
qbert48's Avatar
 
Drives: 2SS SIM
Join Date: Apr 2009
Location: texas panhandle BFE
Posts: 1,143
Quote:
Originally Posted by GTAHVIT View Post
You can't get away with this in CA... Nor any state that has emmisions inspections....


But in FL.....
been to the guys here and good to go they said it's OK in TEXAS maybe i got a pass
__________________
2SS RS SIM gray leather stick shift ground FX
thank you gary richards @ classic chevy in sugarland

welcome home
1100 4-27-09
6000 6-27-09


yes i got to the dance late don't hate me
qbert48 is offline   Reply With Quote
Old 11-07-2009, 09:13 PM   #14
Indpowr
Account Suspended
 
Drives: Corvette C6
Join Date: May 2008
Location: Florida
Posts: 7,028
I plan on adding mesh when we get our gfx kit.
Indpowr is offline   Reply With Quote
Old 11-07-2009, 10:12 PM   #15
scythezo6
Virologist in the making
 
scythezo6's Avatar
 
Drives: 2010 VR SS/RS LS3
Join Date: Aug 2009
Location: El Paso TX
Posts: 2,868
You need to lift the car to remove the bezels? Or can they be popped off easy?
Looks good btw.
__________________
Victory Red 1SS/RS Ordered - 8/4/09 & Joined Camaro5.com family
6000, Delivered to the customer - 12/21/09
scythezo6 is offline   Reply With Quote
Old 11-16-2009, 02:59 PM   #16
Li0nel1234
What should I name my car
 
Li0nel1234's Avatar
 
Drives: 2010 Camaro 2SS RS IOM
Join Date: Jul 2009
Location: San Antonio, TX
Posts: 770
Send a message via AIM to Li0nel1234
You don't need to for the outlets. You can from your driveway. I did but my neck was sore. I don't know if you can with the muffler still in place it might make it more difficult.
__________________
Performance: ARH 2"/"3 headers + ARH 3" HF catback system, SS brake lines, hawk HP+ pads, motul RBF 600 fluid, K&N CAI (w/custom insulation), plug wires, air scoop, Hurst STS, Pedders Track II suspension, 18x10 wheels, 295/45/18 Nitto NT05s
Looks: powder coated iom calipers, LED foglights w/ always on harness, custom painted bowties, window tint, smoke tinted tail lights etc, oem gfx w/ custom outlets, painted taillight bezels, all weather trunk mat
Li0nel1234 is offline   Reply With Quote
Old 08-15-2011, 11:52 PM   #17
Mr.Maro23
 
Mr.Maro23's Avatar
 
Drives: 2010 2lt chevy camaro
Join Date: Jun 2011
Location: Miami FL
Posts: 225
WELL WELL WELL MUFFLER DELETE HUH? LOL IM STARTING TO ENJOY IT I DID THE RESONATOR AND MUFFLER DELETE! AT FIRST I WAS LIKE WOW KRAZZY LOUD BUT TODAY WHEN OUT FOR A SPIN FOR THE HECK OF IT AND FOUND MYSELF WITH A TURBO SRT4 LITTLE DID U KNOW WE RACED FROM 1 LIGHT TO ANOTHER AND HAVE TO SAY AMAZINGLY TOOK HIM BY HALF A CAR HOW I DONT KNOW MAYBE THE DRIVER I GUESS ANYWAYS, GUY GETS NEXT TO ME AND ASKS WHAT THE HELL U GOT ON THERE SOUNDS SO AWESOME I WENT AND LAUGHED AND SAID RESONATOR/MUFFLER DELETE AND COLD AIR INTAKE THATS BOUT IT HE WAS LIKE MAN FAST CAMARO DUDE AND GAVE ME THE PEACE FINGERS. FROM TODAY ON I HAVENT REGRET IT, SOUNDS LOUD BUT THE MARO IS LIGHTER AND FASTER I MUST SAY OPENS UP PRETTY QUICK NOW!!!! I RECOMMEND IT I GUESS LOL.
Mr.Maro23 is offline   Reply With Quote
Old 02-29-2012, 02:38 PM   #18
GEEo
OKCamaros
 
GEEo's Avatar
 
Drives: '13 WRX STi
Join Date: Mar 2010
Location: Muskogee, OK
Posts: 4,600
Do you have any vid of your muffler delete?

It Looks really cool man.
GEEo is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:05 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.