Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Phastek Performance
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Marketplace > Sponsors Classifieds Marketplace > Audio / Visual / Electronics/ Gauges / Nav

View our official forum sponsors list.


Reply
 
Thread Tools
Old 04-12-2011, 05:54 PM   #35
justdenny
 
Drives: 2011 RJT 2SS/RS
Join Date: Nov 2008
Location: Redding, CA
Posts: 149
are PDIM upgrades covered under warranty on a 2SS?
__________________
09/29/2010 - (1100) 10/19/2010 - (2000)
10/19/2010 - (3000)
10/27/2010 - (3300)
10/28/2010 - (3400) TPW 11/15/2010
11/12/2010 - (3800)
11/12/2010 - (4000)
11/12/2010 - (4B00)
11/13/2010 - (4200) Shipped !!!
11/12/2010 - (4B00)
11/13/2010 - (4200)
11/21/2010 - (4B00)
11/21/2010 - (4800) Rail Ramp Unload
11/23/2010 - (5000) Delivered To Dealer
11/23/2010 - (4200)
justdenny is offline   Reply With Quote
Old 04-12-2011, 09:40 PM   #36
patrickt



 
patrickt's Avatar
 
Drives: still saving!
Join Date: Feb 2010
Location: Reading, PA
Posts: 6,107
Quote:
Originally Posted by justdenny View Post
are PDIM upgrades covered under warranty on a 2SS?
only if there is a problem
__________________
Patrick Trageser
Owner
CUTRAG Performance
484-334-8833
www.cultragfactoryparts.com
Patrick@cultragperformance.com
patrickt is offline   Reply With Quote
Old 04-12-2011, 09:42 PM   #37
patrickt



 
patrickt's Avatar
 
Drives: still saving!
Join Date: Feb 2010
Location: Reading, PA
Posts: 6,107
Quote:
Originally Posted by jeepguy_1980 View Post
What specifically is fixed with this PDIM. I added the PDIM to my 2010 1SS. I experience crackling when I browse other songs, while playing a song. I also get a pop up on the iPhone 4 saying that the accessory isn't supported, even though it seems to work.

Will these issues be fixed?
The main issue was with the use of memory sticks and them not being fully read but I have heard of this poping sound and I believe this is fixed as well
__________________
Patrick Trageser
Owner
CUTRAG Performance
484-334-8833
www.cultragfactoryparts.com
Patrick@cultragperformance.com
patrickt is offline   Reply With Quote
Old 04-15-2011, 11:08 PM   #38
patrickt



 
patrickt's Avatar
 
Drives: still saving!
Join Date: Feb 2010
Location: Reading, PA
Posts: 6,107
order yours today
__________________
Patrick Trageser
Owner
CUTRAG Performance
484-334-8833
www.cultragfactoryparts.com
Patrick@cultragperformance.com
patrickt is offline   Reply With Quote
Old 04-21-2011, 09:49 PM   #39
patrickt



 
patrickt's Avatar
 
Drives: still saving!
Join Date: Feb 2010
Location: Reading, PA
Posts: 6,107
pleanty in the warehouse
__________________
Patrick Trageser
Owner
CUTRAG Performance
484-334-8833
www.cultragfactoryparts.com
Patrick@cultragperformance.com
patrickt is offline   Reply With Quote
Old 04-22-2011, 02:48 PM   #40
96_2010_CAMARO
 
96_2010_CAMARO's Avatar
 
Drives: 2012 SIM Camaro 2SS/RS , liberty kk
Join Date: Jun 2008
Location: somewhere beyond
Posts: 385
Send a message via MSN to 96_2010_CAMARO
ok i have a 2010 2ss without on star ( not in america ) and the hands free dosent work i only can use bluetooth for music but my friends 2011 2ss has hands free

what parts do i need to make hands free work ??? ( i checked i have a mic )
__________________
2012 2SS/RS silver ice metallic camaro
96_2010_CAMARO is offline   Reply With Quote
Old 04-22-2011, 08:35 PM   #41
patrickt



 
patrickt's Avatar
 
Drives: still saving!
Join Date: Feb 2010
Location: Reading, PA
Posts: 6,107
Quote:
Originally Posted by 96_2010_CAMARO View Post
ok i have a 2010 2ss without on star ( not in america ) and the hands free dosent work i only can use bluetooth for music but my friends 2011 2ss has hands free

what parts do i need to make hands free work ??? ( i checked i have a mic )
Unfortunatly the hands free bluetooth goes through the VIU which is something we are not able to supply
__________________
Patrick Trageser
Owner
CUTRAG Performance
484-334-8833
www.cultragfactoryparts.com
Patrick@cultragperformance.com
patrickt is offline   Reply With Quote
Old 04-24-2011, 05:26 AM   #42
sting808

 
Drives: 2010 SS RS
Join Date: Apr 2009
Location: Honolulu, Hawaii
Posts: 915
Patrick,

Thanks for the quick replies and great service. Just installed it tonight.
Attached Images
 
sting808 is offline   Reply With Quote
Old 04-24-2011, 09:48 PM   #43
patrickt



 
patrickt's Avatar
 
Drives: still saving!
Join Date: Feb 2010
Location: Reading, PA
Posts: 6,107
Quote:
Originally Posted by sting808 View Post
Patrick,

Thanks for the quick replies and great service. Just installed it tonight.
Your quite welcome buddy and thank you. How long did it take to put in?
__________________
Patrick Trageser
Owner
CUTRAG Performance
484-334-8833
www.cultragfactoryparts.com
Patrick@cultragperformance.com
patrickt is offline   Reply With Quote
Old 04-25-2011, 08:17 PM   #44
trm0002
VIN #2G1FT1EW6A9100074
 
trm0002's Avatar
 
Drives: 2010 CAMARO 2SS/RS RJT VIN 00074
Join Date: Oct 2008
Location: Buffalo,NY 'burbs
Posts: 4,204
Send a message via AIM to trm0002
Quote:
Originally Posted by sting808 View Post
Patrick,

Thanks for the quick replies and great service. Just installed it tonight.
Quote:
Originally Posted by patrickt View Post
Your quite welcome buddy and thank you. How long did it take to put in?
Better question is ->Are all the dis-assembly steps in the DIY thread required or can you access just the PDIM module in an easier way if you're just swapping it out and not ADDING everything? Patiently awaiting a response.... well?... WELL ?...WELL ?... lol
__________________
trm0002 is offline   Reply With Quote
Old 04-25-2011, 09:26 PM   #45
sting808

 
Drives: 2010 SS RS
Join Date: Apr 2009
Location: Honolulu, Hawaii
Posts: 915
Quote:
Originally Posted by patrickt View Post
Your quite welcome buddy and thank you. How long did it take to put in?
Guessing ~15-20 minutes. It was pretty quick. Hardest part was trying to remove the console cover without getting ugly pry marks on the hinge frame. Next hardest part was depressing the proprietary GM mini usb connector lock tab. Ended up using a small screwdriver to press the stupid tab down.
sting808 is offline   Reply With Quote
Old 04-25-2011, 09:42 PM   #46
sting808

 
Drives: 2010 SS RS
Join Date: Apr 2009
Location: Honolulu, Hawaii
Posts: 915
Quote:
Originally Posted by trm0002 View Post
Better question is ->Are all the dis-assembly steps in the DIY thread required or can you access just the PDIM module in an easier way if you're just swapping it out and not ADDING everything? Patiently awaiting a response.... well?... WELL ?...WELL ?... lol
I winged it. Helm service manual interior section didn't help or I didn't see details.

1) remove gauge cluster, disconnect single connector and place on the side.
2) remove manual shifter mount(4 screws) mount can tilted to remove console
3) remove single screw next to manual shifter base
4) pull off sides - pressed in and easy to remove (left and right)
5) remove single screw from each side on front console where dash meet
6) remove (2) screws from each side at rear console cover and remove
7) remove (3) scews; left, center, right on the top back of console
8) remove power, usb, and 1/8" analog in sockets from storage area
9) remove console storage lid
10) pull console top portion off to reveal PDIM (between storage and cup holder)
11) press tabs and remove PDIM module and cable
12) install PDIM and re-assemble in reverse order.
13) test before full re-assembly just in case unit DOA.
sting808 is offline   Reply With Quote
Old 04-25-2011, 10:40 PM   #47
Gene Culley
Account Suspended
 
Drives: 2013 SS
Join Date: Dec 2009
Location: Boyertown, PA
Posts: 1,374
Smile

Quote:
Originally Posted by sting808 View Post
Guessing ~15-20 minutes. It was pretty quick. Hardest part was trying to remove the console cover without getting ugly pry marks on the hinge frame. Next hardest part was depressing the proprietary GM mini usb connector lock tab. Ended up using a small screwdriver to press the stupid tab down.
Nice information you gave there. What console cover are you referring to? I don't recall this when I changed my console out.
Gene Culley is offline   Reply With Quote
Old 04-25-2011, 11:07 PM   #48
trm0002
VIN #2G1FT1EW6A9100074
 
trm0002's Avatar
 
Drives: 2010 CAMARO 2SS/RS RJT VIN 00074
Join Date: Oct 2008
Location: Buffalo,NY 'burbs
Posts: 4,204
Send a message via AIM to trm0002
Quote:
Originally Posted by sting808 View Post
Guessing ~15-20 minutes. It was pretty quick. Hardest part was trying to remove the console cover without getting ugly pry marks on the hinge frame. Next hardest part was depressing the proprietary GM mini usb connector lock tab. Ended up using a small screwdriver to press the stupid tab down.
Time's about right- 20 min or less 1st screw out to last screw back in...

Success.
.

.
.
Still pisses me off that the first thing to come up on my iPhone (3GS) is:
.
"This Accessory is Not Optimized for this iPhone...yada, yada, yada..." WTF?
.
The iPod/iPhone is probably the most used "accessory" with this car's setup from what I see- God forbid Apple and GM got their shit collectively together...But, hey, if everything now works (ALL the time and not when it wants to) and all I have to do is ignore that message, I'm good with it.
__________________
trm0002 is offline   Reply With Quote
Old 04-25-2011, 11:19 PM   #49
sting808

 
Drives: 2010 SS RS
Join Date: Apr 2009
Location: Honolulu, Hawaii
Posts: 915
Quote:
Originally Posted by Gene Culley View Post
Nice information you gave there. What console cover are you referring to? I don't recall this when I changed my console out.
The compartment storage lid cover. It impedes the removal of the top console shell at the rear. Once off, the console shell can be easily lifted from the rear, then back slightly for removal. I'm trying not to scratch where the console and dash meets.
sting808 is offline   Reply With Quote
Old 04-25-2011, 11:22 PM   #50
sting808

 
Drives: 2010 SS RS
Join Date: Apr 2009
Location: Honolulu, Hawaii
Posts: 915
Quote:
Originally Posted by trm0002 View Post
Time's about right- 20 min or less 1st screw out to last screw back in...

Success.
.

.
.
Still pisses me off that the first thing to come up on my iPhone (3GS) is:
.
"This Accessory is Not Optimized for this iPhone...yada, yada, yada..." WTF?
.
The iPod/iPhone is probably the most used "accessory" with this car's setup from what I see- God forbid Apple and GM got their shit collectively together...But, hey, if everything now works (ALL the time and not when it wants to) and all I have to do is ignore that message, I'm good with it.
I have an iPod Classic and it works great. Hopefully, the intermittent static went away. I haven't tried my iPhone 4, yet.
sting808 is offline   Reply With Quote
Old 04-26-2011, 10:29 PM   #51
Gene Culley
Account Suspended
 
Drives: 2013 SS
Join Date: Dec 2009
Location: Boyertown, PA
Posts: 1,374
Smile

Quote:
Originally Posted by sting808 View Post
The compartment storage lid cover. It impedes the removal of the top console shell at the rear. Once off, the console shell can be easily lifted from the rear, then back slightly for removal. I'm trying not to scratch where the console and dash meets.
Are you talking about the arm rest? I didn't have to remove that when I did mine and I didn't want to scratch anything either, but it is understandable and another precautionary measure if you did so.
Gene Culley is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY: PDIM + USB Port installation jtzako Camaro DIY & HOW-TO instructions & discussions 156 12-05-2015 10:27 AM
Details about PDIM & Bluetooth functionality & upgrading your non C&C car with them Matt'sSS Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum 55 02-09-2015 08:56 AM
Official PDIM accessory from GM slick rick Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum 190 07-13-2012 06:35 PM
Faulty PDIM symptoms? djamphi555 Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum 2 08-07-2010 03:27 PM
Is there a fuse for the PDIM? What is a MPIM? jpennin217 Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum 0 11-14-2009 08:41 AM


All times are GMT -5. The time now is 04:17 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2016, vBulletin Solutions, Inc.