Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Apex Paul
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Forced Induction - V8

Forced Induction - V8 V8 Supercharger, turbo, nitrous discussions

Reply
 
Thread Tools
Old 02-18-2013, 06:53 AM   #1
MauiSS
 
MauiSS's Avatar
 
Drives: 2011 Black/Black 2SS A6
Join Date: Jun 2011
Location: Maui, HI
Posts: 41
Mounting MSD bap

I am planning on getting the SLP SC soon and was wondering where most of you using the bap are mounting it. Any pictures would also be helpful.
MauiSS is offline   Reply With Quote
Old 02-18-2013, 09:25 AM   #2
2SSCAMARO

 
2SSCAMARO's Avatar
 
Drives: 2010 Camaro Auto
Join Date: Mar 2010
Location: Fl
Posts: 811
MSD BAP Install

I installed it under the rear seat on the driver's side, run the power wires directly to the battery in trunk and the wires that go to the FPCM along the existing bundle under rear seat. The pressure hose to the MAP is routed along the L/H side of the floor pan beneath the interior trim and through the firewall via an existing plug near the brake reservoir that can be drilled and used as a gromet for the MAP hose.
Attached Images
     
2SSCAMARO is offline   Reply With Quote
Old 02-18-2013, 09:36 AM   #3
TinyToasta
 
TinyToasta's Avatar
 
Drives: way too fast....
Join Date: May 2010
Location: Germany
Posts: 294
here u go!
Attached Images
 
__________________
custom build forged LSA, 376ci, TVS2300@15psi, 675rwhp/676ft-lbs, built by Henrik Racing, Customkingz, tuned by Jannetty Racing
JRE rough idle cam, JRE ported lower intake manifold, OD cog drive, 6% OD crank pulley, ported ls3 heads, NW102mm TB, 1/2'' RDS spacer, IW 8-rib drive
Pfadt Cradle Bushings, Arms & Rods, Pedders Supercar w/FE4 conversion, ZL1 sways, HE Twin Carbon Street Slayer, DSS 1000hp Axles
CTS-V Brake upgrade, Street: 22'' Vossen CV1, Strip: 18'' Forgestar F14 on MT Street Radials
TinyToasta is offline   Reply With Quote
Old 02-18-2013, 12:44 PM   #4
MauiSS
 
MauiSS's Avatar
 
Drives: 2011 Black/Black 2SS A6
Join Date: Jun 2011
Location: Maui, HI
Posts: 41
Thnaks a lot 2SSCAMARO and Tiny Toasta, both good places. Tiny where are you running your hose through? Anyone else have a different location?
MauiSS is offline   Reply With Quote
Old 02-18-2013, 01:36 PM   #5
2SSCAMARO

 
2SSCAMARO's Avatar
 
Drives: 2010 Camaro Auto
Join Date: Mar 2010
Location: Fl
Posts: 811
You're welcome. One advantage to installing the MSD unit under the rear seat is that you can leave the USB cord permanently plugged in to the MSD unit coiled up and stored under the trim at the front of the back seat. It will then reach the center console where you can change programming and view the data in live time. The MSD software will not record and save the data in a log form but it will display the voltages and boost in live time as you are driving. I exposed the cord a bit for your viewing.
Attached Images
 
2SSCAMARO is offline   Reply With Quote
Old 02-19-2013, 01:02 AM   #6
MauiSS
 
MauiSS's Avatar
 
Drives: 2011 Black/Black 2SS A6
Join Date: Jun 2011
Location: Maui, HI
Posts: 41
Thanks again 2SS that makes sense. I think I got my mounting spot.
MauiSS is offline   Reply With Quote
Old 02-19-2013, 06:55 PM   #7
PaulT
 
Drives: LS7 2SS RS
Join Date: Nov 2011
Location: Augusta, GA
Posts: 34
Mounted mine in the trunk just over the driver side wheel well. Not sure how to insert picture.
PaulT is offline   Reply With Quote
Old 02-19-2013, 07:57 PM   #8
MauiSS
 
MauiSS's Avatar
 
Drives: 2011 Black/Black 2SS A6
Join Date: Jun 2011
Location: Maui, HI
Posts: 41
Thanks PaulT.
MauiSS is offline   Reply With Quote
Old 04-12-2013, 05:43 PM   #9
Iam Broke
PHAT B33
 
Iam Broke's Avatar
 
Drives: 2012 TF3 Camaro 2SS/RS M6
Join Date: Jun 2012
Location: Dark of the Moon
Posts: 1,398
I like the rear seat location. Thanks for posting.
__________________
Another 1 of 371 '12 T3 LS3 M6's built.
Iam Broke is offline   Reply With Quote
Old 12-10-2014, 01:13 PM   #10
ZL1Naboz
ZL1Naboz
 
ZL1Naboz's Avatar
 
Drives: '13 ZL1,'15 BMW M235I and '15 SS
Join Date: Mar 2013
Location: Winston Salem, NC
Posts: 165
Anybody have a close image of the red/white wire going into the FPCM?

If I am thinking correctly the end of the red/white wire to the FPCM plug is the fuel pump side? this gets the RED wire from the MSD box. And the wire going back up the harness is the switched side from the fuse panel? which gets the ORANGE Wire from the MSD Box

just want to make sure I grab the right wire
__________________
Rotofab, Kook's w/Hiflo Cats, SCT4, Oracle Side Markers, MTX Sub, Escort 9500ix - Blendmount, 18% Lower, ATI Super Damper, ID850 Injectors, Moroso Catch Can, MSD BAP

Pre-Lower Dyno
559.92 RWHP 519 RWTQ
ZL1Naboz is offline   Reply With Quote
Old 12-10-2014, 03:50 PM   #11
SSawdusty
Crewel Jewel
 
SSawdusty's Avatar
 
Drives: RJT-2SS-RS-6M
Join Date: Nov 2009
Location: Nanaimo, BC
Posts: 364
Heres a thread I did on my Whipple install. Page 2 has the MSD installation.
Hope it helps.

http://www.camaro5.com/forums/showthread.php?t=211238
__________________
Whipple SC with 3.875 pulley. MSD BAP. ZR1 MAP Sensor. Granatelli Wires. 160 T Stat. ADM CAI & Scoop. Vmax Ported Throttle Body. Ceramic Coated LG Motorsports Super Pro Headers and Mufflers. Cat Delete. BCP Valve Covers. Roto-Fab W/W Bottle. RX Catch Can & Breather. Elite Tunnel Brace. MGW Shifter . Prosport EVO Boost & A/F Gauges. Autometer Pillar Gauge Pod. Spohn CM Del-Sphere Trailing Arms & Toe Links. BMR Bushings. Foose Speed Wheels. Pirelli 275/305 Tires. New paint by GTC. Tuned by 5252 Motorsports.582rwhp/583rwt
SSawdusty is offline   Reply With Quote
Old 12-11-2014, 10:09 AM   #12
2SSCAMARO

 
2SSCAMARO's Avatar
 
Drives: 2010 Camaro Auto
Join Date: Mar 2010
Location: Fl
Posts: 811
Quote:
Originally Posted by ZL1Naboz View Post
Anybody have a close image of the red/white wire going into the FPCM?

If I am thinking correctly the end of the red/white wire to the FPCM plug is the fuel pump side? this gets the RED wire from the MSD box. And the wire going back up the harness is the switched side from the fuse panel? which gets the ORANGE Wire from the MSD Box

just want to make sure I grab the right wire
Your understanding is correct. Cut the red/white near the FPCM plug and connect the red from the MSD to the cut end of the wire that is still connected to the plug.Then the MSD orange to the remaining cut end of the red/white.
__________________


Just livin' life
2SSCAMARO is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.