Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
JUICEDMOTORSPORTS
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Specific Models / Packages > Camaro 1LE Forum


Reply
 
Thread Tools
Old 05-11-2013, 12:33 PM   #43
OptimusPlez
 
OptimusPlez's Avatar
 
Drives: 2013 Camaro 2SS RS 1LE GBA
Join Date: Apr 2013
Location: Washington State
Posts: 68
Quick question...When I installed the Roto-Fab, everything seated perfectly but when I close the hood, the right side of the hood where the CAI box sits is raised a tiny bit. Anyone else experience that? I suspect it is the seal pushing up on the hood a little bit but am curious if I did something wrong.
__________________
OptimusPlez
2013 2SS RS 1LE GBA -aka- BLACK BEAUTY
Factory NPP
Polished Roto-Fab CAI
Cilajet Sealant
OptimusPlez is offline   Reply With Quote
Old 05-11-2013, 12:50 PM   #44
SWAG1LE
 
SWAG1LE's Avatar
 
Drives: 2013 1LE
Join Date: Mar 2013
Location: West Texas Desert Hell Hole
Posts: 397
I'd loosen the filter heat shield and push it down if there is any play. Perhaps you can push it down some and tighen at the same time allowing you to close the hood fully.

EDIT: I do not have my Camaro with a CAI yet so I may be waaaaaaaayyy off I like your car!
SWAG1LE is offline   Reply With Quote
Old 05-11-2013, 03:12 PM   #45
JambaJuiced
 
JambaJuiced's Avatar
 
Drives: 2013 2SS/RS 1LE AGM
Join Date: Apr 2013
Location: SoCal
Posts: 115
Just installed the cold air inductions kit this am...after a bit fiddling and a few choice words with it, I was finally able to get it to fit correctly...definitely looks nicer then stock, lol of course I don't sit around with my hood popped open either, and sounds more aggressive...

Also installed the gorilla wheel locks in black...makes the wheels look much nicer...
JambaJuiced is offline   Reply With Quote
Old 05-13-2013, 06:35 PM   #46
rjuarez
 
rjuarez's Avatar
 
Drives: 2013 2SS RS 1LE
Join Date: May 2013
Location: United States
Posts: 44
Can't decide between the roto fab or the CAI kit. Could use a little help.
rjuarez is offline   Reply With Quote
Old 05-13-2013, 07:03 PM   #47
right to travel

 
Drives: 2013 Camaro 1SS 1LE SW
Join Date: Aug 2011
Location: Newport RI
Posts: 824
Quote:
Originally Posted by Bauer2 View Post
I should have a Vararam Tune intake on its way now.
I plan on sanding it smooth and painting it gloss black to pretty it up some before I install it.
i thought these didnt work with 2013's
right to travel is offline   Reply With Quote
Old 05-13-2013, 07:46 PM   #48
bluBlud
 
bluBlud's Avatar
 
Drives: 2013 2SS/RS/1LE
Join Date: Mar 2013
Location: CT
Posts: 483
Quote:
Originally Posted by JambaJuiced View Post
Just installed the cold air inductions kit this am...after a bit fiddling and a few choice words with it, I was finally able to get it to fit correctly...definitely looks nicer then stock, lol of course I don't sit around with my hood popped open either, and sounds more aggressive...

Also installed the gorilla wheel locks in black...makes the wheels look much nicer...
Same here - at least with the cover. The main air box went in without too much trouble but squeezing the cover on to lock it down wasn't the easiest fit.
__________________
bluBlud is offline   Reply With Quote
Old 05-13-2013, 08:47 PM   #49
OptimusPlez
 
OptimusPlez's Avatar
 
Drives: 2013 Camaro 2SS RS 1LE GBA
Join Date: Apr 2013
Location: Washington State
Posts: 68
Quote:
Originally Posted by rjuarez View Post
Can't decide between the roto fab or the CAI kit. Could use a little help.
As many smart people on this forum told me, it is a personal choice. They more or less do the same thing though I believe CAI did best in testing. I chose the Roto-Fab because I like the polished tube but others like the black or carbon fiber. All I know is that either one is better than stock. Good luck!
__________________
OptimusPlez
2013 2SS RS 1LE GBA -aka- BLACK BEAUTY
Factory NPP
Polished Roto-Fab CAI
Cilajet Sealant
OptimusPlez is offline   Reply With Quote
Old 05-13-2013, 11:41 PM   #50
rjuarez
 
rjuarez's Avatar
 
Drives: 2013 2SS RS 1LE
Join Date: May 2013
Location: United States
Posts: 44
Quote:
Originally Posted by OptimusPlez View Post
As many smart people on this forum told me, it is a personal choice. They more or less do the same thing though I believe CAI did best in testing. I chose the Roto-Fab because I like the polished tube but others like the black or carbon fiber. All I know is that either one is better than stock. Good luck!
Thanks!!! I know they are both good; just indecisive.
rjuarez is offline   Reply With Quote
Old 05-26-2013, 11:16 AM   #51
Firefighter


 
Firefighter's Avatar
 
Drives: Black '13 2SS/RS/1LE w/NPP/NAV
Join Date: Oct 2012
Location: Tampa by way of Miami...
Posts: 4,392
I have an ADM Race Intake with the washer bottle on it's way. Andy made me an offer I couldn't refuse. I plan on getting it Dynoed this week BEFORE I put on the ADM intake. If I can work out a deal with the shop I will get one afterward also.
Firefighter is offline   Reply With Quote
 
Reply

Tags
1le camaro, cold air intake, engine, improvment

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:43 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2016, vBulletin Solutions, Inc.