Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Cold Air Inductions
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Camaro V6 LLT Engine, Exhaust, and Bolt-Ons

Camaro V6 LLT Engine, Exhaust, and Bolt-Ons Bolt-Ons | Intakes | Exhaust

Reply
 
Thread Tools
Old 02-18-2014, 09:56 PM   #1
717Stunna
 
717Stunna's Avatar
 
Drives: 2010 Slp Camaro ZL327
Join Date: Mar 2012
Location: PA
Posts: 523
Time to pump up the 6 Shooter

Got my isolator ported throttle body and ported intake manifold today can't wait to get installed hoping to see some gains I have all bolt ons now besides cams
Attached Images
 
717Stunna is offline   Reply With Quote
Old 02-19-2014, 12:29 PM   #2
KMPrenger


 
KMPrenger's Avatar
 
Drives: '10 ABM LT/RS, 06 Chevy Colorado
Join Date: May 2009
Location: Jefferson City, Missouri
Posts: 9,627
Good stuff!

I'd recommend getting a 2nd GM manifold gasket while you are at it, and purchasing slightly longer (10mm longer) intake manifold bolts.
__________________
IPF Tune, Custom Magnaflow Exhaust, Vararam intake, MACE Ported Manifold, RX Ported TB, "Black Ice" manifold insulator, Elite Catch Can, ZL1 repro wheels, ZL1 Springs, DRL Harness, Front GM GFX, Heritage grill, Street Scene lower grill, NLP Spoiler, ZL1 rockers and much more!
KMPrenger is offline   Reply With Quote
Old 02-19-2014, 01:03 PM   #3
717Stunna
 
717Stunna's Avatar
 
Drives: 2010 Slp Camaro ZL327
Join Date: Mar 2012
Location: PA
Posts: 523
Stock bolts won't work
717Stunna is offline   Reply With Quote
Old 02-19-2014, 04:16 PM   #4
Ventmaster

 
Ventmaster's Avatar
 
Drives: 2010 Camaro RS 1LT M6
Join Date: Jan 2011
Location: Utah
Posts: 1,640
Actually you can use the stock IM main mounting bolts, but you will be reducing the thread depth by half (from 1" to about 1/2").

Be sure and use a torque wrench (18 ft/lbs) and you should be fine if you're in a hurry to enjoy your new HP!

If you're more patient, a set of 140mm bolts will restore the stock depth. They can be found here- http://www.boltdepot.com/Metric_hex_...?Selected=6238

Either way, have fun
__________________
Airaid CAI, Rx ported TB, Mace ported IM, JBA shorty headers, Richmond 3.73, Borla touring axleback, Hurst short throw, NH-SS fix, IDEALG clutch m/c, SS struts/springs, Spohn trailing arms, Pfadt Racing sways, Pedders radius arm & rear subframe bushing inserts, 2LT gauge pkg.TSW Nurburgs. IPF S/C
Ventmaster is offline   Reply With Quote
Old 02-19-2014, 05:26 PM   #5
Nutbutt


 
Nutbutt's Avatar
 
Drives: 2011 RJT 2LT/RS Convertible
Join Date: Nov 2009
Location: Western Massachusetts
Posts: 3,242
let the fun begin !
__________________
1st IPF Supercharged 2011 2LT/RS RJT Convertible
Nutbutt is offline   Reply With Quote
Old 02-19-2014, 06:25 PM   #6
Eddiefuzz
 
Eddiefuzz's Avatar
 
Drives: 2011 RS
Join Date: Apr 2011
Location: Florence New Jersey
Posts: 588
Isn't the SLP Camaro already modded?? You don't need longer bolts for the 3/8 iceolator.
Eddiefuzz is offline   Reply With Quote
Old 02-19-2014, 06:44 PM   #7
rtcat600man
having FUN now 13.66@101
 
rtcat600man's Avatar
 
Drives: 2010 2LT IOM
Join Date: Nov 2009
Location: Clarkston, Michigan
Posts: 8,138
When torquing the bolts be sure to do it when everything is cold. you do not want to strip ones of those holes. also, be sure to come back a week later and check the bolts, again when everything is cold.

Yes, you can use the stock bolts with the 3/8 spacer.

Yes, using a second gasket avoids having to use any silicone sealant.
__________________
rtcat600man is offline   Reply With Quote
Old 02-19-2014, 06:51 PM   #8
717Stunna
 
717Stunna's Avatar
 
Drives: 2010 Slp Camaro ZL327
Join Date: Mar 2012
Location: PA
Posts: 523
Yes the the Camaro came modded with a slp blackwing intake and slp exhaust and a diablosport programmer but the exhaust was to raspy and the intake looked stock so I took all of it off and modded it how I want yes its not a ZL327 anymore but it still has the badges to full people hah
717Stunna is offline   Reply With Quote
Old 02-19-2014, 10:40 PM   #9
717Stunna
 
717Stunna's Avatar
 
Drives: 2010 Slp Camaro ZL327
Join Date: Mar 2012
Location: PA
Posts: 523
Im going to wait to install it i just ordered mace cams so I'm getting done all at once
717Stunna is offline   Reply With Quote
Old 02-19-2014, 10:45 PM   #10
KMPrenger


 
KMPrenger's Avatar
 
Drives: '10 ABM LT/RS, 06 Chevy Colorado
Join Date: May 2009
Location: Jefferson City, Missouri
Posts: 9,627
yes you can use the stock bolts with the 3/8" ice-olator....In fact I used them myself when I was just running one gasket and then gasket maker on the other side.

But the recommendation from RX at the time was when using two gaskets, that getting longer bolts for the added depth was a good thing...so that's what I ended up doing. Like mentioned above...don't tighten over 18 ft lbs...especially when your only running half the depth on the bolts.

I'm looking forward to seeing your build! Keep us informed.
__________________
IPF Tune, Custom Magnaflow Exhaust, Vararam intake, MACE Ported Manifold, RX Ported TB, "Black Ice" manifold insulator, Elite Catch Can, ZL1 repro wheels, ZL1 Springs, DRL Harness, Front GM GFX, Heritage grill, Street Scene lower grill, NLP Spoiler, ZL1 rockers and much more!
KMPrenger is offline   Reply With Quote
Old 02-20-2014, 03:04 PM   #11
Ventmaster

 
Ventmaster's Avatar
 
Drives: 2010 Camaro RS 1LT M6
Join Date: Jan 2011
Location: Utah
Posts: 1,640
I would never contradict you KP- you are much too well informed! And I also recommend the use of longer mounting bolts when using 2 IM gaskets.

I just wanted to avoid the misinformation that stock bolts will not work in that application.

Stunna good luck with the Mace cams- keep us posted!
__________________
Airaid CAI, Rx ported TB, Mace ported IM, JBA shorty headers, Richmond 3.73, Borla touring axleback, Hurst short throw, NH-SS fix, IDEALG clutch m/c, SS struts/springs, Spohn trailing arms, Pfadt Racing sways, Pedders radius arm & rear subframe bushing inserts, 2LT gauge pkg.TSW Nurburgs. IPF S/C
Ventmaster is offline   Reply With Quote
Old 02-20-2014, 07:44 PM   #12
rtcat600man
having FUN now 13.66@101
 
rtcat600man's Avatar
 
Drives: 2010 2LT IOM
Join Date: Nov 2009
Location: Clarkston, Michigan
Posts: 8,138
I ended up with the longer bolts when I ordered the plenum spacer. It was at this time adding the plenum spacer that I added the second gasket. Sorry I did not use the stock bolts when I added the 2nd gasket.
__________________
rtcat600man is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.