What Did You Do To Your Camaro Today? - Page 1634 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Leo72793 · 10-12-2019, 10:19 PM

Went to a Cruisin show for charity today. Shined up really nicely!

Camaro2ss2010 · 10-13-2019, 11:34 AM

Installed puddle lights, elite e2 catch can and an MGW shifter. The shifter was worth every minute of my time that I was cussing. If anyone is debating on doing the conversion but is on the fence about it I would say go for it. It’s like driving a completely different car.

InFiD3ViL · 10-13-2019, 12:59 PM

Quote:

Originally Posted by mbesman

Got quoted 325 and 375 to wrap my roof. Tried doing it myself with Ebay wrap. 30 bucks. I removed all trim and antenna. Not too bad, just followed directions off from this forum and vids from you tube. Prepped and tooled up. Well...complete fail. Sooooo....called up another place but I let them know I removed everything already and they dont have to put back. Just wrap roof. Cost 160 out the door with 3m. Took them 20 min. I think it came out great.

Yeah, that looks awesome. I figured with all the wrapping you have done, it would have been a piece of cake. What issues did you run into to decide to have the pros do it? Was it the Ebay wrap that made it difficult or did you just get a premium wrap from Ebay? I have some VVivid gloss carbon fiber wrap that is a nightmare to work with. It is just so damned thick.

I wrapped my hood in 3M 1080 Satin Black. It wasn't hard, just tedious, and I had to take my time. I was afraid of ruining the wrap, but it came out great. It was a very nice wrap to work with. I have thought about doing my roof too, but I don't know how it would look with the sunroof and figure it would give me additional problems. The wrap looks great with the reverse mohawk roof though.

spyderbuddy · 10-13-2019, 05:32 PM

Took A Kid to a Car Show
Won Best in Show in Class

StingrayblueSS · 10-13-2019, 08:44 PM

Not today but I installed my Vararam

mbesman · 10-13-2019, 08:59 PM

Quote:

Originally Posted by InFiD3ViL

Yeah, that looks awesome. I figured with all the wrapping you have done, it would have been a piece of cake. What issues did you run into to decide to have the pros do it? Was it the Ebay wrap that made it difficult or did you just get a premium wrap from Ebay? I have some VVivid gloss carbon fiber wrap that is a nightmare to work with. It is just so damned thick.

I wrapped my hood in 3M 1080 Satin Black. It wasn't hard, just tedious, and I had to take my time. I was afraid of ruining the wrap, but it came out great. It was a very nice wrap to work with. I have thought about doing my roof too, but I don't know how it would look with the sunroof and figure it would give me additional problems. The wrap looks great with the reverse mohawk roof though.

Thanks...I think it was the wrap I got from Ebay. It was real thick and just became a b.... to work with. Eventually I was at the point of no return..2 hours into it I gave up. Laying the stripes is a lot different than a roof. If I were to do it again it definately is a two man job and I would buy a premium wrap like 3M or similar.

Panda1LE · 10-14-2019, 03:17 PM

Ikon sides to match the new front splitter

ragtop1 · 10-14-2019, 04:45 PM

Quote:

Originally Posted by Camaro2ss2010

Installed puddle lights, elite e2 catch can and an MGW shifter. The shifter was worth every minute of my time that I was cussing. If anyone is debating on doing the conversion but is on the fence about it I would say go for it. It’s like driving a completely different car.

What was the shifter that you replaced? And what makes this one better?

xstuntman · 10-14-2019, 05:06 PM

Quote:

Originally Posted by Panda1LE

Ikon sides to match the new front splitter

Interested in these myself.
How was Ikons quality overall?
Boxed well for shipping?
Easy to install?
Enough hardware?
I've read most of the side skirts need painted for uv protection.

Camaro2ss2010 · 10-14-2019, 07:01 PM

Quote:

Originally Posted by ragtop1

What was the shifter that you replaced? And what makes this one better?

I replaced the factory one with the MGW. I have had the hurst and it does not compare to this one. It replaces the complete shifter assembly.

Panda1LE · 10-14-2019, 07:35 PM

Quote:

Originally Posted by xstuntman

Interested in these myself.
How was Ikons quality overall?
Boxed well for shipping?
Easy to install?
Enough hardware?
I've read most of the side skirts need painted for uv protection.

Quality is pretty good, no complaints. Shipping was decent, in plastic and in cardboard , could have maybe used a layer of bubble wrap, install was easy (line up, used 3m VHB tape where it comes in contact with side skirts, then used some self tapping screws i had laying around, didnt like the screws provided by them), hardware was not sufficient as they sent 6-8 black screws, i didnt paint them, was going to wrap them but my roll wasnt large enough, so i got impatient and just put them on. Good enough product for me

InFiD3ViL · 10-14-2019, 08:26 PM

Quote:

Originally Posted by Panda1LE

Quality is pretty good, no complaints. Shipping was decent, in plastic and in cardboard , could have maybe used a layer of bubble wrap, install was easy (line up, used 3m VHB tape where it comes in contact with side skirts, then used some self tapping screws i had laying around, didnt like the screws provided by them), hardware was not sufficient as they sent 6-8 black screws, i didnt paint them, was going to wrap them but my roll wasnt large enough, so i got impatient and just put them on. Good enough product for me

They look awesome. If I didn't already have GFX I would have those.

lemontwist · 10-14-2019, 08:53 PM

got my new ac delco heater core,blend door and a 2015 ss HUD.now the PIA dash removal begins this weekend

InFiD3ViL · 10-14-2019, 09:38 PM

Quote:

Originally Posted by lemontwist

got my new ac delco heater core,blend door and a 2015 ss HUD.now the PIA dash removal begins this weekend

There you go. Turning a negative into a positive! Just convince yourself the HUD was planned from the beginning.

10-12-2019, 10:19 PM	#22863
Leo72793 Drives: 2011 2SS/RS Join Date: Feb 2016 Location: Jacksonville FL Posts: 1,194	Went to a Cruisin show for charity today. Shined up really nicely! Attached Images __________________ •2011 Camaro SS 2SS/RS A6 •MRR M017 1le Replica Wheels •Vararam Ram Air Intake •Speed Engineering Longtube Headers w/ Magnaflow HF Cats •Bo White PnP Stage 2 TB •GPI SS2 VVT Cam w Cometic thin gaskets 10.69 compression •Xpipe w/ Res Delete and NPP Exhaust •Tuned By Anonymous Calibrations •Gen5DIY Mylink Conversion W/ Backup Cam •Morel 3 way custom speakers, Infinity 860w Subwoofers in trunk baffle •Helix P6 6ch amp w/ 8ch DSP and P1 Sub amp

10-13-2019, 11:34 AM	#22864
Camaro2ss2010 Drives: 2010 Camaro 2SSRS M6 Join Date: Jan 2019 Location: Alabama Posts: 1,249	Installed puddle lights, elite e2 catch can and an MGW shifter. The shifter was worth every minute of my time that I was cussing. If anyone is debating on doing the conversion but is on the fence about it I would say go for it. It’s like driving a completely different car. Attached Images

10-13-2019, 05:32 PM	#22866
spyderbuddy Drives: 2010 RS Inferno Orange Metallic Join Date: Mar 2010 Location: Albany, Ga. Posts: 3,410 View My Garage	Took A Kid to a Car Show Won Best in Show in Class Attached Images __________________ Hot Wheels Emblems and Floor Mats, Morimoto Fog Lights, PCP Hideaway Headlight Covers, BBK Headers & High Flow Cats, ZL1 Add-ons Wicker Bill, TL1/ZL1 Hood Insert, Gen5 DIY Frameless Mirror, ABL Dash Lighting & My link Navigation, Blacked out Rear Bowtie, all Sylvania led Turn Signals, Ceramic Window Tint By Nicks, MBRP Exhaust tips, GEN5 DIY Virginia Legal DRL Harness, Painted Brake Calipers, Vittesse Throttle Controller & Paddle Shifter Heritage Grill, Manual Shifter Boot, CNC Throttle Body, Trifecta Tune, Trunk Black out and Side Grills, Hot Wheels door Sills.

10-13-2019, 08:44 PM	#22867
StingrayblueSS Drives: 2013 Camaro SS Join Date: Feb 2017 Location: Indiana Posts: 901	Not today but I installed my Vararam Attached Images

10-14-2019, 03:17 PM	#22869
Panda1LE Drives: 2013 2SS/RS 1LE (6spd) Join Date: Mar 2018 Location: Temecula, CA Posts: 281	Ikon sides to match the new front splitter Attached Images __________________ CAI intake, Stainless Power LTH, SCT X4, NPP exhaust

10-14-2019, 08:53 PM	#22875
lemontwist Drives: 12 2SS/RS L99,11 2SS/RS LS3totaled Join Date: Jun 2019 Location: mooresville nc Posts: 1,048	got my new ac delco heater core,blend door and a 2015 ss HUD.now the PIA dash removal begins this weekend

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GM memo to dealers	Moose	5th Gen Camaro SS LS LT General Discussions	41	02-04-2010 07:33 PM
Major Pedders Event in Houston! Saturday, Jan 30th! Meet DMS	Info@PeddersUSA.com	USA - Texas	39	02-01-2010 12:48 PM
Answeres to questions I have stumbled on	dieseldave24v	5th Gen Camaro SS LS LT General Discussions	13	02-23-2009 06:56 PM