09-06-2015, 01:06 PM | #29 |
Drives: 2014 SS/RS Manual Dual Mode Exhaust Join Date: Jun 2014
Location: United States
Posts: 4
|
Hey everyone, thanks for the great information! I had my front bumper replaced by a local repair shop thru my insurance and they left the pair of Torx Head screws tightened clockwise. I had to tightened the pair of Torx Head screws in the counter-clockwise direction in order to adjust my front bumper down to make it flush with the hood.
__________________
2014 SS1, RS, Silver Ice Metallic, Manual, Dual Mode Performance Exhaust
|
04-15-2016, 06:56 AM | #30 |
Drives: 2012 Camaro 1SS LS3 Join Date: Jul 2008
Location: Jacksonville FL
Posts: 1,114
|
Old thread resurrection.... What size torx screwdriver do I need to adjust the screws? My hood is also low in the very front, but even on the sides. I have adjusted the bumper stops, but will need to adjust the torx screws to get the center part even.
|
04-15-2016, 08:47 AM | #31 |
Drives: 2011 1SS/RS IBM Camaro Join Date: Jan 2011
Location: Chittenango, NY, USA
Posts: 7,219
|
Just got mine adjusted correctly. Should have had the wife sit in the car and pull the lever 23 times. For bump stops and 6 shims.
__________________
|
12-26-2017, 06:55 PM | #32 |
Drives: 2010 Black 2ss Camaro SS Join Date: May 2010
Location: Rochester Hills, MI
Posts: 1,061
|
reviving a old thread....how much play is there in the torx adjustment screws? I put on a new hood, and have it flush everywhere but at the front of the cowl, behind the mail slot....the hood is about a 1/8 inch lower. I can raise the front two bumpers, or the hood will not latch. I have loosened the torx screws about two full turns, but have not noticed a change....continued loosing them? I do not know how much play there is and do not want the bolt to come loose.
thanks
__________________
ZL1 10 spokes,Dart 388,ECS Supercharger 2200x, E85 Flex Fuel sensor, Dart 388 , B&M Tranny Cooler, Vigilante 4000 Triple Disc TC,Katech Ported Heads, Texas Speed Sheet Metal Intake, ECS Big Blower Cam,ID 1700s, Fore Triple Pumps, E85,ATI Super Dampner, KW V3 Coilovers, Pfadt front and rear sway bars,Pfadt Trailing arms and toe rods,ZL1 Rear Diff, RPM 6l90e level 10 Tranny, SW Long Tubes no cats,Nick Williams Boosted 102mm TB, Dr Phil Tune,Borla Atak
|
04-11-2018, 10:31 AM | #33 |
Drives: 2017 zl1 ,2010 SS /RS L99 Join Date: Sep 2017
Location: Long Island ,Ny
Posts: 380
|
Help any pics anyone can post !!vis Terminator hood
Trying to install the terminator fiberglass hood . It sits a little off to one side where there is a slight gap between the side panel and the side of the hood . Also the front centre of the hood sits flush but towards the front side it sits lower than the bumper . Am I missing anything . ? If I loosen the bumper screws to raise the hood up then the hood doesn't latch. Lol it's so frustrating..
__________________
2017 zl1 - rotofab CAI , PDR , Nav .
2010 camaro SS - Procharger D1 sc (Stage 2 with upgraded intercooler)+ whole lot of other goodies ( too many to list ) |
04-03-2020, 04:54 PM | #34 |
Ever figure anything out? ^
|
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
MPD1 "Z/28 style" ram air hood | Eric-MPD1.com | Exterior Parts & Accessories | 665 | 09-10-2014 06:42 AM |
Specter Werkes Camaro GTZ Extractor Hood | ACS Composite | Cosmetics and Lighting Modification Discussions | 18 | 07-02-2011 09:11 AM |
New Specter GTR Extractor Hood | ACS Composite | Exterior Parts & Accessories | 15 | 09-27-2010 08:23 PM |
custom hood, need stripes | asmith10 | Cosmetics and Lighting Modification Discussions | 2 | 08-09-2010 10:13 AM |
Anyone in California Want a Carbon Fiber hood in Trade for there OEM Hood | henri26900 | USA - California | 7 | 09-24-2009 12:19 PM |