1LE Splitter Install - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

olblue75 · 04-25-2015, 02:21 PM

Finally getting ready to install my splitter and on the side templates do I cut them or use the edges of the actual 8 1/2 x 11 paper????

HaubSS · 04-25-2015, 04:40 PM

You cut them out of the paper. I just installed mine on Thursday. It was fairly simple. Once I cut the templates out I held the corner brackets in place to get an idea how exactly the tomato should line up with the lines on the car. Once I did that it all clicked and made sense. Good luck!

olblue75 · 04-25-2015, 05:24 PM

Yeah kinda did the same thing by laying brackets up on the fascia and your right fairly simple. An used nuts and bolts instead of plastic rivets. Trying to figure out where to put the rivets in the 4 holes on the bottom side

rimhof · 07-25-2015, 04:52 PM

Where did you all get the installation papers and templates?

olblue75 · 07-25-2015, 10:02 PM

Came with the splitter

Aero_Sport_Concepts · 07-25-2015, 11:56 PM

Quote:

Originally Posted by olblue75

Yeah kinda did the same thing by laying brackets up on the fascia and your right fairly simple. An used nuts and bolts instead of plastic rivets. Trying to figure out where to put the rivets in the 4 holes on the bottom side

Bolts are the best way IMO. Mine was installed by dealer at purchase but after adding our Extension Kit to it over time the rivets started to let go. I reattached and replaced rivets with Stainless Bolts Nuts and now i can stand on the Splitter Extension no lie.

Thank you

Kurt Robinson
Aero Sport Concepts

rimhof · 07-26-2015, 08:23 AM

Quote:

Originally Posted by olblue75

Came with the splitter

Mine did not. There is just a note that says "instructions of this part are available through GM service information...".

04-25-2015, 02:21 PM	#1
olblue75 Drives: 2010 2SS/RS Join Date: Dec 2009 Location: Clarksville Tennesse. Posts: 6,066	1LE Splitter Install Finally getting ready to install my splitter and on the side templates do I cut them or use the edges of the actual 8 1/2 x 11 paper????

04-25-2015, 04:40 PM	#2
HaubSS Drives: '11 IBM 2SS/RS LS3/M6 Join Date: Feb 2011 Location: Lemoore, CA Posts: 469 View My Garage	You cut them out of the paper. I just installed mine on Thursday. It was fairly simple. Once I cut the templates out I held the corner brackets in place to get an idea how exactly the tomato should line up with the lines on the car. Once I did that it all clicked and made sense. Good luck! __________________ 2011 IBM 2SS/RS - LS3/M6 - Grey Interior Full bolt-ons + TSP 229/236, 112 LSA Tuned by STARKWEATHER PERFORMANCE BMR Stage 3 suspension MRR 288 - 20x10(+35), 20x11(+43)

04-25-2015, 05:24 PM	#3
olblue75 Drives: 2010 2SS/RS Join Date: Dec 2009 Location: Clarksville Tennesse. Posts: 6,066	Yeah kinda did the same thing by laying brackets up on the fascia and your right fairly simple. An used nuts and bolts instead of plastic rivets. Trying to figure out where to put the rivets in the 4 holes on the bottom side

07-25-2015, 04:52 PM	#4
rimhof Drives: 2014 Camaro SS Join Date: Nov 2014 Location: Orlando, Florida Posts: 117 View My Garage	Where did you all get the installation papers and templates?

07-25-2015, 10:02 PM	#5
olblue75 Drives: 2010 2SS/RS Join Date: Dec 2009 Location: Clarksville Tennesse. Posts: 6,066	Came with the splitter