03-20-2014, 12:32 PM | #1 |
Emerald Coast Camaros
Drives: 2013 2SS/RS L99 Join Date: Dec 2013
Location: Pensacola Fla. ~Mike & Kym~
Posts: 656
|
BMR suspension mods done
Finally got most of the suspension mods I wanted to install and ready to get a little seat time. Installed BMR trailing arms & adjustable toe rods, BMR front and rear sways, as well as the BMR 1" lowering springs. Upgraded some rear bushings but havent jumped off into a full cradle bushing swap (yet). I do have the Peddlers agressive street alighnment setup in the car now. Obtw, the elongation of the front subframe mounts was a PITA and took the most time (and blood). LOL
And looking to make a drive up to Valdosta for the "pony wars" and run the strip and autox event and have some fun with the SS in a few weeks. Any C5 guys going to run the autoX ? I could use some pointers on air pressure and sway bar setups that can be done onsite as I plan on driving up there. PM me.
__________________
|
03-20-2014, 12:54 PM | #2 |
Drives: SS Join Date: Mar 2013
Location: USA
Posts: 221
|
Looking good. Good luck in the Pony wars!
|
03-20-2014, 01:03 PM | #3 |
Drives: Chevys at the limit Join Date: Nov 2010
Location: SLC, UT
Posts: 9,621
|
Congrats on the upgrade! Nice touch painting the stock endlinks. How are you liking the setup so far?
Best regards, Tyler 888-308-6007 |
03-20-2014, 01:05 PM | #4 |
Drives: 2000 Camaro SS Join Date: Feb 2010
Location: Louisville, Ky.
Posts: 25,179
|
Those new parts are just a little bit beefier than what they are replacing.
|
03-20-2014, 01:09 PM | #5 |
Drives: 2010 Camaro 2SS/RS Join Date: Mar 2013
Location: Dallas, TX!
Posts: 290
|
Looks great! Ahhhhhh....yet another thing on my mod list of things to do.
|
03-20-2014, 01:29 PM | #6 |
High-tech Redneck
Drives: '10 CGM SS, '02 2500HD, '09 300SRT8 Join Date: Nov 2010
Location: Lexington, KY
Posts: 757
|
Great Job!!...My alignment is tomorrow for the similar mods. Congrats. Don't forget to post how you do on the track.
__________________
"My friends call me Chris. Are you my friend?"
2010 CGM L99 2SS/RS - GPI SS3 VVT, BTR DoD Delete, Circle D 4c, BTR springs, Katech C5R Timing Chain, MRR-228 315/275, CAI, Elite catch-can, TSP 1 7/8" Headers + offroad pipes, Magnaflow 3", Pfadt springs, BMR LCAs, toelinks, trailing arms, cradle bushings, & sway bars w/ endlinks, Vitesse paddles, heritage grille, and an eBay splitter. Power upgrades by Race Proven Perf.; Tuning by ShorTuning. |
03-20-2014, 01:34 PM | #7 |
Emerald Coast Camaros
Drives: 2013 2SS/RS L99 Join Date: Dec 2013
Location: Pensacola Fla. ~Mike & Kym~
Posts: 656
|
Tyler- I havent had the chance to test the handling limits yet but the general feel of "spirited" runs on some of a few curvy backroads and a few adandoned parking lot manuevers and I can tell a noticable difference. Havent been back to the 1/8 mile strip yet to see how it launches on a prepped track but the rear end feels a little better planted and I havent noticed that walking around feeling when I hard plant the throttle in a turn. I hope to see how it feels in Valdosta in the autoX where I can actually see my timed runs. Only 8k on the original Pzeros so I will see how they do.
__________________
|
03-20-2014, 01:37 PM | #8 |
Res Ipsa Loquitur
Drives: 2013 Camaro SS Vert Supercharged Join Date: Sep 2012
Location: Southern Maryland
Posts: 726
|
Subscribed. Ordered my BMR goodies from Tyler this week.
__________________
"STREET LEGAL" 2013 Camaro 2SS/RS LS3 Convertible -- 2.9l Whipple Supercharger, CDC SportBar, Cordon CR-1 and MRR M017 wheels, Hex Vents, RPI ZL1 Splitter, CAI, Pfadt Tri-Y Headers, high-flow cats, ZR1 3 bar map sensor, ZL1 fuel pump, 3.875" pulley, ADM FPCM, 1LE PCV Oil Separator Kit, Elite Catch Can, APEX scoop and washer bottle relocation kit, Hotchkis lowering springs, BMR sways, BMR toe rods, BMR trailing arms, 620 rwhp, 564 rwtq, and tuned by Andrew Zurick of Complete Street Performance by way of Maryland Speed.
|
03-20-2014, 03:48 PM | #9 | |
Drives: Chevys at the limit Join Date: Nov 2010
Location: SLC, UT
Posts: 9,621
|
Quote:
Thank you sir! Best regards, Tyler 888-308-6007 |
|
03-20-2014, 04:13 PM | #10 |
Drives: 2012 2SS/RS LS3 Join Date: May 2012
Location: Pearland, TX
Posts: 388
|
That ride height looks bad ass! Congrats on the upgrades man. Did this come as a package? What part #s?
__________________
Victory Red 2012 2SS/RS LS3 Camaro
Pat G. Spec Cam from Cam Motion 228/236 .599/.599 112+2LSA Kooks 1-7/8" LTs w/ Cats Roto-Fab, Bo White TB, Borla Touring Catback 3.91 1LE Gears, MGW Tuned by Pat G |
03-20-2014, 04:39 PM | #11 |
Drives: Race Car Join Date: Sep 2009
Location: Seffner, FL
Posts: 6,226
|
Congratulations on the new parts!!! Looks GREAT!!!! I like your paint mod on the rear end links too!!!
|
03-20-2014, 05:17 PM | #12 |
Drives: 2011 Camaro SS Join Date: Apr 2012
Location: Jacksonville FL
Posts: 348
|
Nice on the upgrades. I just did a similar install myself
__________________
|
03-20-2014, 05:35 PM | #13 | |
Emerald Coast Camaros
Drives: 2013 2SS/RS L99 Join Date: Dec 2013
Location: Pensacola Fla. ~Mike & Kym~
Posts: 656
|
Quote:
Thanks. But nothing was in a package, I just picked out the parts to suit my intended driving style and went from there. I wanted to go a little lower in ride height but decided I would rather enjoy driving it more if I didnt. It seems to ride almost as good as the factory springs, I think it may have lost a little weight transfer to the rear from a dig but maybe its just my perception, only another track day will tell. Obtw, most everything I ordered for this Camaro was either from Chase or Tyler. Both great guys to deal with. FYI- Even if you dont see it in their website catalog, it doesnt mean they dont sell it. Call them.
__________________
|
|
03-20-2014, 05:58 PM | #14 |
|
Congrats on the parts man . They look good.😗enjoy !!
Sent from my iPhone using Tapatalk
__________________
The DREAM is free... It's the HUSTLE that is sold seperately
|
|
|
Tags |
bmr |
|
|