03-19-2011, 06:40 PM | #1 |
Drives: 2010 supercharged LS3 Join Date: Jan 2010
Location: Le Mars, Iowa
Posts: 2,235
|
DIY: change Brake Pads/ rotors
I noticed awhile back that a few people were asking for a DIY for changing pads and rotors with some pictures. I figured I could snap a few pics when I was installing my new Hawk pads and write one up quick.
Tools Needed: 1/2" drive breaker bar with 3"-5" extension 1/2" drive ratchet 18mm and 22mm Socket Torque Wrench 1/8" pin punch and hammer T30 torx bit wire coat hanger floor jack and jack stand(s) Optional - 2 C-clamps First break loose the lug nuts with the breaker bar, extension and 22mm socket. Next jack up the vehicle, secure with jack stand, and remove the wheel. Next step will be to loosen the pins that hold the break pads in. (this is much easier when the caliper is still bolted to the car) Using your 1/8" punch and hammer, hit these 2 pins so that they are broken loose. If you are only chaning the pads and don't intend to remove the rotors you may remove the pins completely and pull the brake pads out the top of the caliper. You might need to use a screw driver to pry the pads out by putting it thru the pin hole and prying up against the caliper. After getting the pads out you will need to push the pistons back into the caliper to make room for the new wider pad. I was able to do this by just removing the cap from the brake fluid resivoir and pushing them back squarely with my fingers. I only removed one pad at a time so the pistons on the other side of the caliper had nowhere to go and the fluid went back into the resivoir. Drop the new pads in, put the bottom pin all of the way thru and use your hammer to seat it back into position. next insert flat gold hold down spring under the bottom pin. Push down on the top of the spring so you can slide the other pin over it and into place. Seat that pin with the hammer and you are done. If you are removing the rotor as well, or if you want a simpler way to get the new pads into the caliper, you will need to remove the caliper. You will need the ratchet and 18mm socket to remove the 2 bolts on the back side of the caliper that hold it onto the car. DO NOT let the caliper hang by the break line. Use your wire coat hanger to hang the caliper from the spring. If you are chaning your pads with the caliper off you will still need to completely remove both of the pins holding in the pads. if you wish to use the C-clamps to retract the pistons, then don't remove your old pads yet. Use them to squarely and evenly push back the pistons with the C clamps. From that point changing the pads is the same as in the description above. I personally take the rotors off and rub them with some 240grit emery cloth or have them turned to get any residue from the old pads off. To Remove the rotor you will need to remove the T30 torx bolt from the rotor. After removing that bolt it should just pull straight off. *NOTE* if removing a back rotor you must have the E-brake disengaged in order to pull it off. To put everything back together simply to the reverse of how you took it apart. Make sure when you tighten your lug nuts back up you tighten them to the proper torque spec for your wheels. Factory wheel torques can be found in the owners manual under Capacities and Specs. Last edited by Big Brunsy; 03-20-2011 at 05:17 PM. |
03-19-2011, 07:59 PM | #2 |
Only drives on Sundays
Drives: '16 2SS A8 NPP MRC NGray Join Date: Feb 2011
Location: Dalton, GA
Posts: 2,500
|
Very nice writeup. I replaced my roller skates with Hawk ceramic, but I had my dealer do it because I didn't feel comfortable. But if I ever do my rotors, this will be bookmarked.
Padre |
03-19-2011, 08:02 PM | #3 |
Banned
Drives: 2010, 2SS, IOM/CGM Stripes, 4/24/10 Join Date: Jun 2010
Location: Houston,TX
Posts: 841
|
Great write-up....I'll put this in the "To-Do" list!!! THANKS!
|
03-19-2011, 10:10 PM | #4 |
buzzy56
|
Excellent
Excellent write up. I will use this for reference in the future when the time comes for some hawks.Darn dust anyway.Eh !
__________________
OLD SCHOOL / NEW SCHOOL COOL
|
03-21-2011, 02:08 PM | #5 |
Drives: 2010 supercharged LS3 Join Date: Jan 2010
Location: Le Mars, Iowa
Posts: 2,235
|
Thanks, it was my first one. I get so much from this site I just wanted to contribute something.
|
03-24-2011, 03:51 AM | #6 |
Drives: '94 Camaro Z28 Join Date: Jan 2011
Location: Orlando,Florida
Posts: 1
|
I was able to change my brake pads for the first time using your DIY instructions. Thanks. Hope you can add some videos about how to replace brake pads in the future..
Last edited by hybenz; 03-26-2011 at 05:02 AM. |
04-11-2011, 01:44 PM | #7 |
**Sold n' Sad**
|
Great write up, it will sure help C5 members save money doing it themselves.
The only thing i wanted to clarify for other members new to DIY brake work is the 'turning' of the rotors. I know you stated you sometimes have them turned to remove old brake pad residue. My suggestion for getting the rotors turned is to level out the grooves the old pads made. This fresh turned rotor is now completely flat which allows the new brake pads to "bed" properly to the flat surface of the rotors which is important in getting the best performance & life out of your brakes. Just my thoughts, it's only two more bolts to remove the caliper, along with the torx that hold each rotor on....dont stop short go the rest of the way and get them rotors turned! I have NAPA and oriely's auto who can turn rotors, It's around $5 per rotor
__________________
2011 Camaro 2SS, SIM, 6M, HUD, 10% tint, black out lenses, SS emblems, TSP 304 LT's, Roto-Fab, MGW shifter, gto res, 8K BFXENON, HP Tuners, Redline Fluids. ***Sold*** Now in an 11' F150 supercrew FX4.
Still addicted to the this forum |
04-11-2011, 05:34 PM | #8 |
I have no life
Drives: 06' Subaru STI, ex-Camaro V6 LLT Join Date: Apr 2010
Location: Top Gear Test Track
Posts: 3,189
|
Cool! Do most of these steps apply to the V6 brakes? The single piston? I never knew you had to disengage the handbrake to remove the rear rotors! I learn something new everyday =D
__________________
|
04-11-2011, 05:38 PM | #9 |
Account Suspended
Drives: 89 IROC 350 Join Date: Mar 2009
Location: Back roads, southern Ohio
Posts: 12,504
|
No. The V6 doesn't have the pads you can change without removing the caliper. Other then that, it's pretty similar. You don't need the punch as the pads will come out once you remove the caliper. On the brembos, they won't.
|
04-11-2011, 07:44 PM | #10 |
I have no life
Drives: 06' Subaru STI, ex-Camaro V6 LLT Join Date: Apr 2010
Location: Top Gear Test Track
Posts: 3,189
|
thanks for that info!
__________________
|
04-11-2011, 07:54 PM | #11 |
Drives: 2010 Camaro SS/RS 6spd Join Date: Sep 2009
Location: Jefferson, Ga
Posts: 4,399
|
How about the rears? I know on my mustang you need a special tool to turn the piston back in because that is how the e-brake works
__________________
|
04-11-2011, 08:59 PM | #12 |
Drives: Acura RSX Type S Join Date: Apr 2011
Location: Philly
Posts: 24
|
Sweet write up. Thanks. Sorry if this is a stupid question but by opening the reservoir using your approach and hanging the caliper from the wire if it is removed, does this eliminate any need to bleed the brakes?
|
04-16-2011, 12:59 AM | #13 | |
Drives: 2010 supercharged LS3 Join Date: Jan 2010
Location: Le Mars, Iowa
Posts: 2,235
|
Quote:
you are not removing any brake lines, so there should be no way for air to get into the brake line. So you do not have to bleed the brakes. |
|
04-16-2011, 06:26 AM | #14 |
Drives: 2010 Camaro SS/RS 6spd Join Date: Sep 2009
Location: Jefferson, Ga
Posts: 4,399
|
[QUOTE=Big Brunsy;3101620]The E-brake on the Camaro is kind of like a drum brake inside the rotor, so no special tools required.
That's like the rears on my F150! But my Mustang is totally different! Thanks for the info!
__________________
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Stainless Works Longtube w/High Flow cats plus Hawk Ceramic Brake Pads | Xplosive Performance | V8 Bolt-Ons & Tunes | 5 | 04-13-2011 08:03 AM |
DBA Brake Rotors, Hawk Brake Pads, and Motul Fluids! | AJ@ECSMotorsports | Suspension / Chassis / Brakes | 49 | 11-13-2010 03:57 PM |
***STILLEN Camaro5 SS Brake System Upgrade Package*** | Team STILLEN | Suspension / Chassis / Brakes | 20 | 08-06-2010 10:49 AM |
FS: SS rotors, brake lines, pads, springs. trailing arms. | Darth_Emma | Suspension / Chassis / Brakes | 0 | 08-05-2010 07:25 PM |
Brake upgrade | 96CAMaro | Wheels and Tires Talk Sponsored by The Tire Rack | 28 | 06-03-2009 01:44 PM |