05-13-2013, 09:33 AM | #43 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
#
__________________
|
05-15-2013, 08:54 PM | #44 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Taking a step backwards. Trying to find out why my MSD 2-step slows Pumpkin down 7 10th's. Sock wires are back on and the MSD module is mouthed as far from the plug wires as possible.
__________________
|
05-22-2013, 01:07 PM | #45 | |
Account Suspended
|
Quote:
I was unsuccessful, SO our service manager tried and got it in about 10 minutes, even got the gray clip back in and it started. the rest of it will be a piece of cake |
|
05-22-2013, 01:10 PM | #46 | |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Quote:
__________________
|
|
05-22-2013, 02:18 PM | #47 |
Account Suspended
|
|
05-22-2013, 03:21 PM | #48 | |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Quote:
__________________
|
|
06-04-2013, 11:43 AM | #49 | |
Account Suspended
|
Quote:
What settings did you finally end up with on your CTAP-01 ? |
|
06-04-2013, 06:10 PM | #50 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Have yet to use it due to issues with the MSD box, but I have a two stage two step R&D box on the way from Lingenfelter for testing. I'll let you know soon as I can.
__________________
|
11-11-2013, 08:23 AM | #51 | |
Account Suspended
|
Quote:
The 2 step was causing it to think my car was running low octane fuel and pulling 15 deg of timing. My tune has been adjusted for that now I haven't got back to the track yet but on my street tires it just smokes the tires now so I believe it should run now. |
|
11-11-2013, 10:17 AM | #52 | |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Quote:
__________________
|
|
11-11-2013, 10:39 AM | #53 |
Account Suspended
|
|
11-11-2013, 11:13 AM | #54 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
My MSD 2-step box is in the trash bin, it slowed Pumpkin down 7/10th's with a random misfire. Lingenfelter box works mint.
__________________
|
11-11-2013, 11:27 AM | #55 |
Account Suspended
|
I will see what happens but on the street on street tires it is not laying over anymore
of course just spinning A couple weeks ago I was at the track and on my M/T drag radials it would launch and then just go flat I am hoping that is corrected 2.45 60 and I know it runs better then that my car is not a stock build 472 RWHP |
05-10-2016, 06:29 PM | #56 |
Drives: 2015 2ss Join Date: Jun 2015
Location: Wooster ohio
Posts: 586
|
I know this is a old thread but just wondering if you can set a delay in the 2 step turning on.
Say when you push the clutch to the floor the 2 step does not activate for 1-2 seconds. Mainly for power shifting or no lift shifting. So the 2 step don't activate going down the track. Or is there a way to add a button on the shifter where the clutch has to be pressed to the floor and the button pressed to turn it on. I think I'll go with the ligenfelter box based on this thread for this set up would I need then ctap box or is it possible to just run the 2step box off of a button |
|
|