Add HUD to your 2010

[dragom]

Originally Posted by afireinside

Hey I would have LOVED a roll up windows, rear seat and radio delete as a option in the new camaros. HUD just seems something for the "Bimmer" crowd.....

I bet this is coming from someone that has never owned a car with HUD. I had a gran prix that had HUD in it and I loved it. I can't wait for the mod to be done so I can get mine done. Don't knock something till you have tried it.

[DWALEX]

Originally Posted by afireinside

Hey I would have LOVED a roll up windows, rear seat and radio delete as a option in the new camaros. HUD just seems something for the "Bimmer" crowd.....

These 12 vehicles still offer manual windows as standard equipment, though all of them can be optioned up into the modern era: Chevrolet Aveo, Chevrolet Cobalt, Ford Fiesta, Ford Focus, Hyundai Accent, Kia Rio, Kia Forte, Nissan Versa, Smart Fortwo, Toyota Corolla and Matrix, Toyota Yaris

[SteveDoten]

Need help on the Hud install???

I need someone who is ready for the Hud upgrade in the Northeast

I am located 2 hours from NYC and Boston

Talked to Ofer(thread starter) on Saturday, the harness is proven, we just need to get the projector installed

I am doing this install pro-bono(Free)

You just need to pay for the Hud, bezel, switch

[SSLarry]

This thread seems to have gotten hijacked.

This is about installing a HUD on a 2010. NOT should you install a HUD on a 2010. I wonder if the moderator can go in a delete all the bullshit.

[bad_bear]

Yep.........

[2010IBMSS]

Originally Posted by SSLarry

I wonder if the moderator can go in a delete all the bullshit.

getting ridiculous...

[camaro4mybday]

the thread has not gotten jacked there are people that can not or do not feel comfortable doing there install so they have inquired from there own local shops about cost or what would be a fair cost. steve has been kind enough to offer help to anyone who wanted to do it and i stated a pricing example of someone going to a shop to have it done. NO ONE is soliciting work from this thread and if the moderators feel i have commited a violation i will be more than happy to remove my postings

[lionssfan]

How did you determine what is the correct gage wire to use for each circuit within the harness. Just want to make sure each circuit can carry the amperage. thanks

[lionssfan]

what vin had the connector on the harness for the ABL lighting. and this is for the ambient lighting on the passenger side dash right. mine doesn't light up, but the door panels does. thanks

[baba booey]

Originally Posted by lionssfan

How did you determine what is the correct gage wire to use for each circuit within the harness. Just want to make sure each circuit can carry the amperage. thanks

Did you read the whole thread

[lionssfan]

yes sorry dont recall seeing it I'll go back

[lionssfan]

I have the schemadics for the hud but haven't figured out how to past it on the site yet if anyone is interested. I plan on doing this hud mod this winter.

[Tnpjohnson]

I just got my 2010 camaro. It's in the paint shop get a custom paint job
I'm very interested in the HUD. Has any one put it in the dash yet?
I see that it works sitting on the dash board but is the air ducting the same as the 2011
Would love to have this in my car

Thxs Tom johnson

[lionssfan]

The head-up display is a secondary display system capable of reflecting important vehicle information onto the windshield. The vehicle information is displayed using virtual imaging and is reflected on the windshield in front of the driver. Battery positive voltage is the power source to the head-up display. The head-up display can only be enabled when the ignition is active and in RUN position. The head-up display receives vehicle information for display via the serial data circuit. The head-up display switch signal circuit is pulled up to battery voltage in the head-up display. The head-up display also provides the head-up display switch with a low reference. The head-up display switch is a momentary contact switch that connects a series of resistors in a resistor ladder format. The head-up display monitors the head-up display switch signal circuit to determine the head-up display switch inputs. Each switch state PAGE, UP, DOWN corresponds to a certain resistance value. The head-up display determines the switch pressed by the voltage drop across the resistors. The head-up display intensity can be changed by using the head-up display dimming switch. The head-up display is turned OFF using the dimming switch. The head-up display does not have a separate Off switch.