Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
dave@hennessey
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Tuning / Diagnostics -- engine and transmission


Reply
 
Thread Tools
Old 11-15-2009, 11:03 AM   #1
camaro1

 
camaro1's Avatar
 
Drives: 550+RWHP 2010 camaro
Join Date: Sep 2007
Location: wisconsin
Posts: 1,588
new hptuners custom O/S

latest hptuners software has an upgrade-able 2.5bar operating system for the LS3,L99, now you can have an actuall VE table and cooling fan control below 192*f


- 2.5 bar (255 kPa) max MAP sensor support (calibration capability for GM 0-5V linear MAP sensors)
- Rescaled MAF High Freq table supports up to 15400 Hz with 300 Hz resolution, also supports airflow up to 1024 g/sec
- New VE tables with 33 x 33 cell resolution each and configurable MAP and RPM axes (choose your own resolution)
- Charge Temperature based VE multiplier table, configurable axis
- TPS based VE multiplier table, 33 x 17 cells with configurable TPS and RPM axes
- MAP referenced Boost Enrich table
- Boost Enrich MAP threshold and hysteresis value
- Both MAF and Speed Density mode supported
- Boost based fuel cut, selectable MAP threshold cuts fuel to all cylinders when exceeded
- Rescaled fan temperature axis 163-250F (73-121C), stock is 192-250F (89-121C)

you can use the 2.5 bar upgrade with the factory map sensor in N/A form since the ve/map table is fully adjustable, i just copied my vertual ve table from bluecat eq program to a junk ls2 file then copied and pasted that to my adjusted ve table, then used the interpolate function to fill in all the 0's because the 2.5bar table is 2 times as big as the ls2 style table
__________________
415ci stroker, TVS 2300 Magnacharger, cnc heads, cam, yank ss3200 converter, Kooks long tubes, Bwoody true cold air kit, ZL1 Pump, magnaflow 3" cat-back, lowering springs,BMR control arms and tie rod bars, 3.73 gears, diff mounts, RX can, ADM fuel controller
camaro1 is offline   Reply With Quote
Old 11-15-2009, 02:21 PM   #2
2Tightwads
Banned
 
Drives: 2002 LS1 swapped into a 1994 Z
Join Date: Sep 2009
Location: San Antonio, TX
Posts: 386
Good news!
2Tightwads is offline   Reply With Quote
Old 11-20-2009, 12:03 AM   #3
camaro1

 
camaro1's Avatar
 
Drives: 550+RWHP 2010 camaro
Join Date: Sep 2007
Location: wisconsin
Posts: 1,588
just got around to playing with the new 2.5bar O/S,, really nice to have an actuall VE table, and the new cooling fan controls works great

and no more resetting the pcm by disconnecting the batt or pcm after every ecm write!
__________________
415ci stroker, TVS 2300 Magnacharger, cnc heads, cam, yank ss3200 converter, Kooks long tubes, Bwoody true cold air kit, ZL1 Pump, magnaflow 3" cat-back, lowering springs,BMR control arms and tie rod bars, 3.73 gears, diff mounts, RX can, ADM fuel controller

Last edited by camaro1; 11-20-2009 at 02:24 AM.
camaro1 is offline   Reply With Quote
Old 11-20-2009, 05:37 PM   #4
ohfck
 
Drives: 2010 RJT M6 bone stock ... for now
Join Date: Oct 2009
Location: Houston
Posts: 11
Thanks for the news, saw on HPTuners where you're having problems with your gauge pack, what is it doing?
ohfck is offline   Reply With Quote
Old 11-20-2009, 06:49 PM   #5
camaro1

 
camaro1's Avatar
 
Drives: 550+RWHP 2010 camaro
Join Date: Sep 2007
Location: wisconsin
Posts: 1,588
the oil temp gauge is off about 40*f and the trans temp is off about 25*f, the gauges are just a 3 wire set-up, +, -, and serial data from the ecm,

if you compare the data for oil temp and trans temp they are way off

has also happened to other camaro's i tuned,, i think most people wouldnt notice it if you were not watching the scan data while looking at the gauges

the data for the gauges comes straight from the ecm serial data line, something changes after flashing with hp tuners and the gauges no longer read correctly,, i was actually in contact with an engineer from GM and he has seen this issue before with aftermarket tuning software
__________________
415ci stroker, TVS 2300 Magnacharger, cnc heads, cam, yank ss3200 converter, Kooks long tubes, Bwoody true cold air kit, ZL1 Pump, magnaflow 3" cat-back, lowering springs,BMR control arms and tie rod bars, 3.73 gears, diff mounts, RX can, ADM fuel controller

Last edited by camaro1; 11-21-2009 at 08:57 AM.
camaro1 is offline   Reply With Quote
Old 01-23-2010, 10:05 AM   #6
Mark-HD
 
Mark-HD's Avatar
 
Drives: 2010 Inferno Orange SS
Join Date: Sep 2009
Location: Atlanta, Ga.
Posts: 226
Have you figured out or has there been any progress on the gauge issue?
__________________
2010 Camaro SS, M6, MTI shifter and sway bars, GM quarter flares, Corsa catback, Roto-Fab CAI, 30% tinted windows, Lloyd's custom mats, Hawk ceramic pads, Pedders lower coils, Magnuson supercharger with 3.6 pulley, BMR trailing arms & toe rods, Kook's LT's1 7/8 w/cats, Lingenfelter/SLP billet pedals, KW V'3 Coilovers, RevExtreme catch can, ---Ordered--- IconZ LS7 9 & 11" polished wheels!. Dyno'd 563.05 HP, 543.86 Torq.
Mark-HD is offline   Reply With Quote
Old 01-23-2010, 10:17 AM   #7
camaro1

 
camaro1's Avatar
 
Drives: 550+RWHP 2010 camaro
Join Date: Sep 2007
Location: wisconsin
Posts: 1,588
car is in storage now, hptuners thinks it was fixed in the latest beta software, ill have to wait till spring to find out
__________________
415ci stroker, TVS 2300 Magnacharger, cnc heads, cam, yank ss3200 converter, Kooks long tubes, Bwoody true cold air kit, ZL1 Pump, magnaflow 3" cat-back, lowering springs,BMR control arms and tie rod bars, 3.73 gears, diff mounts, RX can, ADM fuel controller
camaro1 is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Custom Magnaflow Exhaust buddylok Camaro V6 LLT Engine, Exhaust, and Bolt-Ons 49 05-16-2016 11:02 AM
Custom Painted Stripes Underway for Bumleb's Rally Yellow 2SS RumbleBeeSS Cosmetics and Lighting Modification Discussions 140 06-20-2010 12:12 AM
SCT Xcal 3 w/ Custom Tunes now available!!! Meister@Torq V8 Bolt-Ons & Tunes 17 12-24-2009 05:02 PM
The Official Thread about Custom Paint! pinkcamaro10 Cosmetics and Lighting Modification Discussions 30 03-28-2009 07:17 PM


All times are GMT -5. The time now is 06:50 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.