01-28-2013, 11:23 AM | #3851 |
|
Just ran out of money for mods so I don't frequent the forum as much as I used to.
Saving up for a 2014 Corvette! Have you seen that thing? Gotta have one! Sorry for the thread jack.
__________________
|
02-02-2013, 08:45 PM | #3852 |
|
BSR if you get the C7 I will be so jealous! I was anxiously waiting for 13 January and the debut, and it was worth the wait. I want that car so bad, I seriously hope you get one so you can drive me around in it!
|
02-02-2013, 08:53 PM | #3853 |
|
C'mon you can't let a little thing like money stop you.
__________________
|
05-11-2015, 01:58 AM | #3854 |
Drives: 2011 Camaro LS Join Date: Dec 2014
Location: CA
Posts: 36
|
my apologies for not having read the entire 155 pages.
But is it just me or the Vararam V6 video instruction showed some questionable discrepancy. there are three installation videos on the V6 Vararam intake page. the first video at 4:28 (long video) shows the radiator brackets facing outward; meaning the sides where he cut the plastic are facing the wheel wells, as oppose to the second video right below it at 0:28 showing the cutting side facing inward towards the radiator. has anyone noticed this? so which one is the correct one? Vararam should clarify.
__________________
2011 Camaro LS/ZL1 Spoiler/ACS T5 Front Splitter/K&N drop-in filter
|
05-11-2015, 08:41 AM | #3855 |
Drives: 16 Camaro SS, 15 Colorado Join Date: May 2009
Location: Jefferson City, Missouri
Posts: 13,943
|
Here is how mine is cut/shaved. I shaved the inside portion down. You'll need to shave them down pretty far for good clearance.
Also, I cut the rubber part to lean the radiator backwards, and then took the portion I cut out and shoved it in front to keep it tight.
__________________
2016 Camaro 1SS - 8-speed - NPP - Black bowties
2010 Camaro 1LT V6 (Sold. I will miss her!) |
05-11-2015, 08:01 PM | #3856 | |
Drives: 2011 Camaro LS Join Date: Dec 2014
Location: CA
Posts: 36
|
Quote:
__________________
2011 Camaro LS/ZL1 Spoiler/ACS T5 Front Splitter/K&N drop-in filter
|
|
05-12-2015, 01:12 PM | #3857 |
Drives: 16 Camaro SS, 15 Colorado Join Date: May 2009
Location: Jefferson City, Missouri
Posts: 13,943
|
Yep correct. Make sure you shave them down far enough so that the part you shave down is perfectly level with the front (side towards the engine bay). The first time I shaved mine down I didn't get them quite far enough, and this resulted in the Vararam intake shifting slightly when I drove the car.
__________________
2016 Camaro 1SS - 8-speed - NPP - Black bowties
2010 Camaro 1LT V6 (Sold. I will miss her!) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DIY: Vararam CAI Install with Color Photos | Jeanius | Camaro DIY & HOW-TO instructions & discussions | 22 | 05-26-2015 02:48 PM |
R2C Cold Air Intake Installed!! | TXGooch21 | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 15 | 12-01-2013 09:40 PM |
Vararam installed!!! | BackinBlackSS/RS | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 654 | 06-20-2012 07:35 AM |
GMPP v6 intake | FirstCamaro2k10 | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 4 | 05-18-2011 05:05 PM |