12-22-2009, 02:55 PM | #43 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
Not bad but then you will have to cut the wires coming in to the plug in the back and wire in some connectors and where do you put the parts to run the EL wire?
One more thing is the flasher on this car? |
12-22-2009, 03:06 PM | #44 | |
|
Quote:
Connect up a 194 bulb socket Via a Scotchlock connector, put both the 194 and the 3156 bulb into the housing, seperate them by a piece of metal bent into the u shape following the afterburner shape. Either way whatever light is used for the turn signal, it would still flash. |
|
12-22-2009, 03:18 PM | #45 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
Don't forget if you go with a LED or EL wire that the load changes and the DIC will have a problem with it.
|
12-22-2009, 03:31 PM | #46 | |
|
Quote:
http://www.eautoworks.com/product-Led-33226.htm |
|
12-22-2009, 03:34 PM | #47 | |
Drives: 2011 GT500 Join Date: Jun 2008
Location: southern california
Posts: 902
|
Quote:
|
|
12-22-2009, 03:41 PM | #48 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
I know that but it dos not work, I was tolled that it did not work by AAC , I will try it sone to.
|
12-22-2009, 04:03 PM | #49 |
|
heres a pic from the film clip of the concept for whoever maybe able to photoshop or just for referance . who made the concept lights or does one exist ? i have only seen retouched pics of them and this pic of a real concept does not look so hot ,maybe if it was lit we could see whats going on in there. i have a new rs taillight in hand now if i can get the lens off without scratching it i will post pics of inside.
__________________
2010 Hennessey HPE650 2SSRS Blk/Blk
Magnuson TVS2300,ported heads,cam,Hotchkis suspension. Weld 17”s, Mickey Thompson’s. Last edited by klatterblast; 12-22-2009 at 04:25 PM. |
12-22-2009, 04:32 PM | #50 |
|
heres a couple pics of mine from an angle , AACstyle afterburner led halos.
__________________
2010 Hennessey HPE650 2SSRS Blk/Blk
Magnuson TVS2300,ported heads,cam,Hotchkis suspension. Weld 17”s, Mickey Thompson’s. |
12-22-2009, 05:25 PM | #51 |
Drives: the 2nd amendment home Join Date: May 2008
Location: OK
Posts: 14,707
|
Instead of thinking 'Afterburner', think 'Eclipse'.
__________________
"They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety."
-- Benjamin Franklin |
12-22-2009, 05:39 PM | #52 |
Drives: 2-70 Camaros,40 chev 2dr sedan Join Date: Jun 2009
Location: Washington
Posts: 45
|
I don't have one to play with but it looks like there are three parts to the housing. The reflective can, the clear diffuser, and the red lense. Has anyone tried taking the light apart and spraying a tailight tinting paint over the clear diffuser, masking off a quarter inch around the bottom half circle. This would slow the light through the center but allow it to shine though around the edges. Might not be as dramatic as LEDs or completely blacking out the center. Sorry I don't have any cool photoshop programs to show what I am talking about.
|
12-22-2009, 06:07 PM | #53 |
Drives: the 2nd amendment home Join Date: May 2008
Location: OK
Posts: 14,707
|
The diffuser is normally part of the lens, molded on the inside.
__________________
"They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety."
-- Benjamin Franklin |
12-22-2009, 06:15 PM | #54 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
There is three parts.
|
12-22-2009, 06:16 PM | #55 |
Drives: 2-70 Camaros,40 chev 2dr sedan Join Date: Jun 2009
Location: Washington
Posts: 45
|
I was using this picture for reference from an older post. It appears that the clear diffuser sits in about .5 to 1 inch seperate from the red lense.
|
12-22-2009, 06:17 PM | #56 |
Drives: 2-70 Camaros,40 chev 2dr sedan Join Date: Jun 2009
Location: Washington
Posts: 45
|
I was too slow posting that one. Thanks 2SSRS.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New Camaro Exterior and Interior Stainless Steel Trim Parts from RPI Designs! | RPI Designs | Cosmetics and Lighting Modification Discussions | 36 | 04-02-2020 05:32 PM |
New Camaro Exterior and Interior Stainless Steel Trim Parts from RPI Designs! | RPI Designs | Exterior Parts & Accessories | 30 | 02-20-2013 03:23 PM |
Drag Racing Suspension Kits | Info@PeddersUSA.com | Suspension / Chassis / Brakes | 25 | 02-21-2010 08:48 PM |
Official Camaro Convertible CONCEPT Press Release | Tran | Camaro Convertible Forum | 12 | 11-18-2009 07:05 PM |
The DEFINITIVE EXPLANATION OF CAMARO SUSPENSION, ISSUES, AND UPGRADES | Info@PeddersUSA.com | Suspension / Brakes / Chassis | 106 | 10-19-2009 06:08 PM |