how's this for the NEC5 logo?

[600hp-lpe]

Does this one work for the NEC5 logo?

It's clean with most of the design elements people wanted...

It'll work for shirts, hats, stickers, etc.

[Havok]

I like. Simple but gets the message across.

[PAUL SS]

The NEC5 on the door and the circle 5 below that is reduddant with the New England Camaro5 under the car. Can NEC be somehow worked into the circle 5? I like where this is heading.

[600hp-lpe]

Originally Posted by PAUL SS

The NEC5 on the door and the circle 5 below that is reduddant with the New England Camaro5 under the car. Can NEC be somehow worked into the circle 5? I like where this is heading.

Remember, we were using the abbreviated "NEC5" as our club identifier.
It needs to be somewhere. I had tried to place it in the circle,
it wasn't readable. It was way too small.

It won't work inside the circle for embroidered shirts or hats either..
The NEC5 may still be too small when shrunk a little more than the size I posted.

[PAUL SS]

Originally Posted by 600hp-lpe

Remember, we were using the abbreviated "NEC5" as our club identifier.
It needs to be somewhere. I had tried to place it in the circle,
it wasn't readable. It was way too small.

It won't work inside the circle for embroidered shirts or hats either..
The NEC5 may still be too small when shrunk a little more than the size I posted.

Okay, I get that, but there are three 5's on that one logo! Looks like we are getting close, just some details to work out.
By the way, nice work cleaning up that car.

[chevy 3]

I like the way you did it 600. I like so where do I order shirts from. I'd take two large and two small in gray

[600hp-lpe]

ok... here's 2 more.. slightly different. Either will work when shrunk down to be embroidered on a polo or hat... probably better than the first one. I like the one with the circle on the 5. (the top one)

you need the "new england camaro 5" on the bottom..
otherwise people will keep asking you "what does NEC5 stand for?"

you are right with the extra redundant 5 though.. so I drew these 2 alternates.

Only way the NEC looks ok inside the circle is sideways and then it doesn't look right 'cause it don't fit on the door/too small on the door.

yup... the camaro looks better "cleaned up". I want to get the style set that everyone likes, then I'll edit the pixels and straighten out the lines.

[Tessa]

Originally Posted by 600hp-lpe

Does this one work for the NEC5 logo?

It's clean with most of the design elements people wanted...

It'll work for shirts, hats, stickers, etc.

In line with what Paul was saying -- I like the NEC5 and then spelling out New England Camaro 5...but...the logo on the car -- NEC5 above the circle 5 makes it look like NEC55....
Does it look stupid if its just NEC over the circle 5??

[Tessa]

Originally Posted by 600hp-lpe

ok... here's 2 more.. slightly different. Either will work when shrunk down to be embroidered on a polo or hat... probably better than the first one.

you need the "new england camaro 5" on the bottom..
otherwise people will keep asking you "what does NEC5 stand for?"

you are right with the extra redundant 5 though.. so I drew these 2 alternates.

Only way the NEC looks ok inside the circle is sideways and then it doesn't look right 'cause it don't fit on the door/too small on the door.

yup... the camaro looks better "cleaned up". I want to get the style set that everyone likes, then I'll edit the pixels and straighten out the lines.

I like the one with the circle better -- what about leaving it with the NEC over the circle like on the original?

[v6sonoma]

Either of those looks good. Perhaps if the 5 and circle were a bit smaller. I don't know what do you guys think?

[600hp-lpe]

Originally Posted by chevy 3

I like the way you did it 600. I like so where do I order shirts from. I'd take two large and two small in gray

We are almost there... hold on a minute. it's going to be cheaper if we all get together and put in a group order.

T-shirt companies typically take the artwork, and import it into their own software .. they have a one-time charge to do that. After it is "vectorized" for their machine, you pay per item (shirt, hat, etc).

Much cheaper to make 30 - 40 shirts all the same than a one-off design for 2-4 shirts due to the setup/graphics charge.

[600hp-lpe]

Originally Posted by Tessa

I like the one with the circle better -- what about leaving it with the NEC over the circle like on the original?

I like it but I think the NEC5 will be really hard to embroider it on a shirt - it would be small like this on the pocket of a polo.. only slightly larger on a hat.

[600hp-lpe]

here are the others shrunk down...

Pretty sure these can be embroidered as-is onto the left side (like where a pocket would be) of a polo shirt.

Either of the 3 are fine for the back of a t-shirt, or a sticker.

[2010 SSRS]

Originally Posted by 600hp-lpe

ok... here's 2 more.. slightly different. Either will work when shrunk down to be embroidered on a polo or hat... probably better than the first one. I like the one with the circle on the 5. (the top one)

you need the "new england camaro 5" on the bottom..
otherwise people will keep asking you "what does NEC5 stand for?"

you are right with the extra redundant 5 though.. so I drew these 2 alternates.

Only way the NEC looks ok inside the circle is sideways and then it doesn't look right 'cause it don't fit on the door/too small on the door.

yup... the camaro looks better "cleaned up". I want to get the style set that everyone likes, then I'll edit the pixels and straighten out the lines.

I think both of these look great, but the one with the Circle would be my first choice.