08-09-2011, 11:10 AM | #29 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
Just placed my lift order yesterday. I went with 2 Backyard Buddy's, one with solid decking one with adjustable jack trays. Extended height but normal width which will measure 9'2" X 15' and will fit nicely.
I am having them delivered and installed by a local lift company for $1500 which is worth the piece of mind knowing they have been properly done. Lift master is giving me a quote for extended height door tracks and 3 jackstaff lifts. I have 3 nice regular lift master lifts now but they are center pull. I also ordered my floor which should arrive next week! Should be a lot of fun! |
08-11-2011, 05:27 PM | #30 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
High rise jackshaft openers are going in tomorrow. Floor should arrive next week. Lifts are a month out.
|
08-16-2011, 10:18 AM | #31 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
High lift openers are done and work great. Floor arrived and is almost finished, I ordered the edging which should arrive Friday to finish the job.
Lifts are still about 5 weeks out. |
08-16-2011, 10:29 AM | #32 |
and MR. HYDE
Drives: 2010 2SS RJT/BLK 6Spd Man Join Date: May 2009
Location: Oxford, Alabama
Posts: 4,375
|
|
08-16-2011, 05:42 PM | #33 | |
I Wanna Go Faster!!
Drives: 2011 2SS Synergy Green M6 Join Date: Apr 2011
Location: SC
Posts: 3,323
|
Quote:
Challenger belongs in there between Bend Pack and Rotary. The CL-10 is one of the few lifts still Made in the USA too. GOOD starts at Challenger and goes up from there in my opinion. If you have the scratch then I wouldn't even consider an Eagle or some POS off brand that you found a deal on the internet on. |
|
08-18-2011, 11:36 PM | #34 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
. . . . . .
I don't have Internet service yet at the new house, it should be set up Monday or Tuesday. I am working off a satellite at the moment, but I will take some photos tomorrow and see if I can post them from my I-Pad. |
08-19-2011, 09:24 PM | #35 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
I have photos, but no idea how to post them from I-Pod, so I will post them next week. Today I finished my Racedeck floor with their edging and it looks nice.
|
08-22-2011, 09:51 AM | #36 |
and MR. HYDE
Drives: 2010 2SS RJT/BLK 6Spd Man Join Date: May 2009
Location: Oxford, Alabama
Posts: 4,375
|
Looking forward to the pictures.
|
08-22-2011, 10:11 PM | #37 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
I'm getting close, we finally got our phone and Internet service today. I picked up a new Apple Air so as soon as I figure it out I will post photos!
I'm shooting for tomorrow! |
09-03-2011, 01:25 AM | #38 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
I know its late but we have been quite busy. Here is a shot of one of the Lift Master Jackstaff openiers. They are very quiet and allow you to use all of your overhead space.
|
09-03-2011, 01:29 AM | #39 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
I have installed the racedeck floor and had the two doors raised to make room for the lifts which are still a couple of weeks out. Its a little cramped at the moment, but should be fine when lifts arrive.
|
09-03-2011, 01:34 AM | #40 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
As soon as I get the lifts in I will be able to get wifes car back into garage which should make life a little easier!
|
09-03-2011, 09:26 AM | #41 | |
Drives: 701 RWHP Lingenfelter/Pedders Beast Join Date: Apr 2009
Location: El Paso
Posts: 2,973
|
Quote:
How do you like the race deck floor?
__________________
Lingenfelter forged balanced and blueprinted LS3, Maggie TVS 2300 LPE 9.5" Rearend 3.73,LPE dual disk clutch,10/14 rib belt drive,
MTI shifter,RPM Level VI,Corsa stainless cat back, Racing Brake Rotors, LPE calipers, LPE twin fuel pumps, American Racing long tube headers, GT9 cam Port and polished heads and an ADM majic tune. 701 RWHP,Fully Pedderized w/complete bushings and Sportsryder Supercar Remote resevior coilovers. CCW 505t's Nitto Invo's and DR's Beware of the LPE Brotherhood! |
|
09-03-2011, 10:15 AM | #42 |
Drives: 2011 Shelby, 2005 SSR, 2011 2SS/RS Join Date: Apr 2011
Location: Georgia
Posts: 109
|
Race deck floor is really nice. It was easy to install and is very durable. It cleans up well and is comfortable to walk on. I also used their drainage tiles over the two drains in my floor.
I have always been a Chevy fan but like all muscle cars. Cobra is a great ride. I am considering adding a Hemi if they release a 426 anytime soon. Other cars under covers are my 2SS/RS and my SSR. |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
College Kid Needs Some Advice :help: | iRock4Christ | Camaro Price | Ordering | Tracking | Dealers Discussions | 6 | 07-01-2011 01:45 PM |
New to Phoenix and Camaro - Need Service Shop Recommendations | Nagilem | USA - Southwest | 5 | 08-02-2010 10:02 AM |
Looking for help with "custom" audio...shop out there? | SA CHEVY | Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum | 9 | 06-07-2010 08:47 AM |
Need Great Body Shop in NJ | WildClay | USA - NY / NJ / PA | 7 | 09-08-2009 09:24 AM |
Jim's 66 Muffler shop in Albuquerque | CamaroGrrl | USA - Southwest | 6 | 08-15-2009 08:47 AM |