09-10-2009, 10:29 AM | #1 |
Drives: 2010 2SSRS m6 Join Date: Jul 2009
Location: Memphis ntn
Posts: 225
|
nitrous results
I thought I would post my nitrous results here since it is a forced induction section. The first dyno sheet is motor only. Stock and after engine work. The second is with with a small tester shot of nitrous and the second is my set up that I run daily. We pulled 5 degrees out and see no knock at all with 91 octane I am spraying through a HSW plate and it comes in real nice. Went through a couple bottle already and this LS3 loves the juice. If anyone here is thinking about nitrous it really brings this car to life.
|
09-10-2009, 11:03 AM | #2 | ||
Truth Enforcer
Drives: anything I can get my hands on Join Date: Sep 2006
Location: anywhere and everywhere
Posts: 22,797
|
nice.
__________________
Never race anything you can't afford to light on fire and push off a cliff
A group as a whole tends to be smarter than the smartest person in that group until one jackass convinces everyone otherwise. Quote:
Quote:
|
||
09-10-2009, 02:27 PM | #3 | ||
Original Bumblebee Owner
Drives: 265hp ZX-14, 500hp Silverado, V-ROD Join Date: Apr 2009
Location: Arizona
Posts: 1,378
|
Sweet! Great results there. Tell us more about both the "engine work" that netted you +75rwhp, and tell more about your nitrous setup.
__________________
Quote:
|
||
09-10-2009, 02:58 PM | #4 |
Drives: many Join Date: Jul 2009
Location: Glenolden PA 19036
Posts: 7
|
Nice results!
Nick |
09-10-2009, 03:19 PM | #5 |
Drives: aqua 2ss l99 Join Date: Jun 2009
Location: Edmonton
Posts: 1,215
|
what size shot 150 or 250?
wet, i assume?
__________________
May your exhaust note, sing in harmony with your blower.
|
09-10-2009, 04:03 PM | #6 |
Drives: 2010 2SSRS m6 Join Date: Jul 2009
Location: Memphis ntn
Posts: 225
|
those are 125 hp jets. We went a little heavier on the fuel than the kits suggested to get the A/F ratio down to a real safe range.
The engine work is Comp cam (custom grind) 219 229 and .561 .572 113 lobe (small cam) 921 dual springs hardened pushrods kooks Long tubes (1-7/8") GMPP offroad axle back exhaust (left stock mid pipes in) New Era intake ZEX nitrous kit with HSW 360 deg spray plate Custom tune with 5 degrees retarded fot the nitrous |
09-10-2009, 06:50 PM | #7 | ||
Original Bumblebee Owner
Drives: 265hp ZX-14, 500hp Silverado, V-ROD Join Date: Apr 2009
Location: Arizona
Posts: 1,378
|
Awesome setup. You are getting 117hp actual from 125hp jets, that's a really good number. Did I miss it? Wet or Dry Kit?
__________________
Quote:
|
||
09-11-2009, 07:57 AM | #8 |
Drives: 2010 2SSRS m6 Join Date: Jul 2009
Location: Memphis ntn
Posts: 225
|
this si a wet ZEX competition kit. Not the kit they make for the camaro as it has tiny solinoids and is basically cheap. Th FI competition kit is the real deal. I did use HSW spray plate and the HSW jets though. And yes properly tuned in i would expect ~115 out of a 125 hsw jet as they are rated low and generally produce good numbers.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Nitrous info | CamaroSpike23 | Forced Induction - V8 | 65 | 03-19-2020 08:22 AM |
Introducing the Nitrous Outlet 2010 Camaro Nitrous System! | Nitro Dave | Forced Induction | 33 | 04-17-2010 08:01 PM |
Nitrous Express Nitrous Kits Available for the 2010 Camaro V6 & V8! | Kris@BMCPerformance | Forced Induction | 5 | 11-04-2009 09:46 AM |
Nitrous Info | Milk 1027 | Wiki | 0 | 08-12-2009 06:26 PM |
BUDWEISER SHOOTOUT LINE UP | CamaroScotty | General Automotive + Other Cars Discussion | 22 | 02-07-2009 07:03 PM |