10-21-2013, 08:47 PM | #15 |
No! You do not want to leave them on, because they could catch on something.
I thought of using a thumb screw type, but not a good idea. I have left my standard jack pads on by accident and they did not fall off. |
|
10-22-2013, 06:49 AM | #16 |
2018 Garnet Red ZL1 conve
Drives: 2013 & 2018 ZL1 vert Join Date: May 2009
Location: Des Moines, IA
Posts: 1,471
|
EVERYONE needs to buy these jack pads, even if you only jack your car up one time, there worth every dime!! You won't be disapointed at all, trust me on this as a 2013 ZL1 vert owner!!
__________________
Build Thread: 2018 ZL1 Vert Purchased (Overpar73)
|
10-27-2013, 10:51 AM | #17 |
Ron and Sugar
Drives: 2013 Black ZL1 Vert A6 Join Date: May 2013
Location: DFW
Posts: 108
|
John, rec'd the aluminum magnetic pad yesterday and I say they are a big improvement and the same quality as the plastic. Thanks very much.
__________________
I Love My 08 Pek a Poo |
11-02-2013, 08:07 PM | #18 |
We now make a magnetic jack pad that fits almost all cars.
|
|
11-04-2013, 07:44 PM | #19 | |
Quote:
I myself use 2 floor jacks to not put a twist in the car as I jack it up. |
||
11-29-2013, 02:25 PM | #20 |
We are out of town until Saturday. Will resume shipping 11/30
|
|
11-29-2013, 02:27 PM | #21 |
We are out of town until Saturday. Resume shipping 11/30
|
|
11-29-2013, 04:33 PM | #22 |
Drives: ZL1, 2013, tri-coat-red, manual Join Date: Nov 2013
Location: Michigan
Posts: 1,607
|
Define high angle. I am jacking now 7 to 8 inches to get wheel dollies under the tires. I have both sets the older and newer for the increased angle. Love them use them alot and they are getting cut through the bottom since the material is soft. Do the aluminum ones get the wear marks, can they not be used for the higher angle? thks
|
11-29-2013, 07:38 PM | #23 |
Native Floridian
Drives: 2014 - ZL1 / 2003 - Corvette Join Date: Oct 2013
Location: FLORIDA
Posts: 2,657
|
I bought a set of 4. Had to remove left front tire the other day and it worked perfectly!!! A must have if you plan on doing any mods yourself!!!
|
01-11-2014, 01:33 PM | #24 |
Thanks!
|
|
01-11-2014, 07:50 PM | #25 |
Drives: Possibly a 1LE in the near future. Join Date: Oct 2012
Location: US Of A
Posts: 436
|
Funny story...
So I just took off all my wheels to clean them and put them back on. Drove around for 45 minutes...and realized when I got back I never removed my pad. Sure enough...it was still there when I got home! Awesome! And they work well! |
01-11-2014, 08:40 PM | #26 | |
Drives: 2016 Corvette Z06 M6 Join Date: May 2009
Location: Odenton, MD
Posts: 874
|
Quote:
These are definitely worth the money. Quick shipping, and I didn't even have to pay until I recieved them and notified John that I was happy with them Don't get any better than that
__________________
2013 Dodge Viper #44/150 Launch Edition IG:@absoluthank
20/21 BC Forged Wheels : BC Coilovers: TA Aero |
|
01-12-2014, 06:05 PM | #27 |
Drives: 2012 Summit White ZL1 Join Date: Dec 2012
Location: San Diego
Posts: 257
|
Great product and a must buy. I use them all the time when I put my drag wheels on and then again when I take them off.
Thanks again John |
01-12-2014, 08:16 PM | #28 |
Drives: 2013 Camaro ZL1 Join Date: Nov 2012
Location: Dubuque, IA
Posts: 880
|
Can you use the standard ones for a 2 post hoist to raise the entire vehicle or do you use the aluminum ones. It says on the website not to raise it any higher than 2'' off the ground when using standard. Is that for durability reasons or the extreme angles when using the floor jack?
__________________
13 ZL1 A6
LSX 427 with AGP Twin Turbos, E85 and Flex Fuel. Built and tuned by ADM Performance 1000rwhp |
|
|
|
|