12-02-2012, 05:38 PM | #29 | |
I Carry!
Drives: 2013 CRT ZL1 Join Date: Jul 2011
Location: Fletcher, Ok
Posts: 2,722
|
Quote:
I think that the tubing for the actuators are too small, stock ones are hard plastic and very big. I will post a pic after dinner of the stock vs. what I had to plumb, the stock will not work.....unless you cut or have access to make this??? We shall see.
__________________
I am a Modaholic!! Please Help!! Do Not feed my addicition....See build...
http://www.camaro5.com/forums/showthread.php?t=261540 From Oklahoma, Join us on Facebook https://www.facebook.com/groups/okcamaros/ |
|
12-02-2012, 06:14 PM | #30 |
Drives: 2017 ZL1 Join Date: Nov 2012
Location: Olive Branch MS
Posts: 103
|
Hold up!
So, in a nutshell, is the LOUD side louder than stock (if so, very noticeably)? I just ordered this and I wanted quite a bit louder...but still have control with m2w. Scott |
12-02-2012, 06:23 PM | #31 | |
I Carry!
Drives: 2013 CRT ZL1 Join Date: Jul 2011
Location: Fletcher, Ok
Posts: 2,722
|
Quote:
Louder than stock on start up, but not overly loud. At highway speeds it is not loud at all, very quiet compared to stock. Again I don't know if the tubing that I re-plumbs that it is not working correctly, I did go out tonight and check the vacuam to make sure that it closed and opened the actuators, Mannualy that is. Still need to get the exhaust from rubbing in spots before I takle that beast.
__________________
I am a Modaholic!! Please Help!! Do Not feed my addicition....See build...
http://www.camaro5.com/forums/showthread.php?t=261540 From Oklahoma, Join us on Facebook https://www.facebook.com/groups/okcamaros/ |
|
12-02-2012, 06:30 PM | #32 | |
Drives: 2017 ZL1 Join Date: Nov 2012
Location: Olive Branch MS
Posts: 103
|
Quote:
Scott |
|
12-02-2012, 06:34 PM | #33 |
Drives: 2017 ZL1 Join Date: Nov 2012
Location: Olive Branch MS
Posts: 103
|
Thanks for your info and input btw
|
12-02-2012, 06:35 PM | #34 | |
I Carry!
Drives: 2013 CRT ZL1 Join Date: Jul 2011
Location: Fletcher, Ok
Posts: 2,722
|
Quote:
__________________
I am a Modaholic!! Please Help!! Do Not feed my addicition....See build...
http://www.camaro5.com/forums/showthread.php?t=261540 From Oklahoma, Join us on Facebook https://www.facebook.com/groups/okcamaros/ |
|
12-02-2012, 06:59 PM | #35 | |
Billy Boat ZL-1 exhaust cammed and long tube ARH headers......
|
||
12-02-2012, 07:22 PM | #36 |
Drives: 2017 Camaro SS1LE 2000 Trans Am WS6 Join Date: Jul 2008
Location: Portland, TN
Posts: 2,955
|
Did you do something to make the tips stick out that far, or is that just how it is? Any drone with the Billy Boat and headers?
__________________
2017 Krypton Green SS 1LE
Magnacharged 2000 Trans Am WS6 manual trans 2002 Trans Am 2015 Ram Crew Cab Cummins |
12-02-2012, 07:24 PM | #37 |
mine was a prototype......no drone at all in quiet mode
|
|
12-02-2012, 07:30 PM | #38 |
I Carry!
Drives: 2013 CRT ZL1 Join Date: Jul 2011
Location: Fletcher, Ok
Posts: 2,722
|
Nice car, I see the tips stick out way to far on the passenger side on yours too. I had to cut mine back a little, also mine are on the ZL1, which things are different than on an SS.
__________________
I am a Modaholic!! Please Help!! Do Not feed my addicition....See build...
http://www.camaro5.com/forums/showthread.php?t=261540 From Oklahoma, Join us on Facebook https://www.facebook.com/groups/okcamaros/ |
12-03-2012, 10:12 AM | #39 |
Petro-sexual
|
Thanks for sharing!!! I like that it's a larger tube and all SS.
__________________
'20 ZL1 Black "Fury" A10, PDR, Exposed CF Extractor Magnuson Magnum DI TVS2650R // TooHighPSI Port Injection // FF // Katech Dual In-Tank // Soler 103 // PLM Heat Exchanger // ZLE Cradle bushings // BMR Chassis-Suspension Stuff // aFe Bars // Diode Dynamics LEDs // ACS Composites Guards // CF Dash // Aeroforce // tint // other stuffs |
12-03-2012, 12:43 PM | #40 |
I Carry!
Drives: 2013 CRT ZL1 Join Date: Jul 2011
Location: Fletcher, Ok
Posts: 2,722
|
Crisis averted, no more rubbing, only cost $40 and about 40 minutes for them to fix. Shop aligned the pipes, no more rubbing on drive shaft, belly tin or rear pumpkin. No rattles or anything!! I had tucked the pipes up too much into the tunnel, causing the pipes to be pulled up too high, thus causing the rubbing issues. Yes, cutting back the pipe was right, because the pipe/muffler was not aligning with the hanger. Yes the Flapper is also working correctly, however I want to plumb the hard lines back in.
The big question of how does it sound? Stock operations, no M2W switches….On start up, acceleration, deceleration and WOT it is deeper than stock. At cruising speed it is quieter than stock. With the M2W operating, it is deeper than stock at all areas. I will say that to me it is not louder than stock, just deeper. But I do have severe hearing loss? Also it is much heavier than stock.
__________________
I am a Modaholic!! Please Help!! Do Not feed my addicition....See build...
http://www.camaro5.com/forums/showthread.php?t=261540 From Oklahoma, Join us on Facebook https://www.facebook.com/groups/okcamaros/ |
12-03-2012, 07:23 PM | #41 |
Drives: 2012 ZL1 #165 Join Date: Apr 2009
Location: Switzerland (no longer Houston, TX) :-(
Posts: 479
|
How much weight does the bb add?
|
12-03-2012, 07:28 PM | #42 |
I Carry!
Drives: 2013 CRT ZL1 Join Date: Jul 2011
Location: Fletcher, Ok
Posts: 2,722
|
__________________
I am a Modaholic!! Please Help!! Do Not feed my addicition....See build...
http://www.camaro5.com/forums/showthread.php?t=261540 From Oklahoma, Join us on Facebook https://www.facebook.com/groups/okcamaros/ |
|
|
Thread Tools | |
|
|