09-18-2015, 07:18 PM | #1 |
Drives: Black 2015 Camaro 2LS Join Date: Aug 2015
Location: houston
Posts: 96
|
Adding a spoiler...
So I been looking around and found this z28 "look alike" and it has solid reviews but its only $99. Looks to good to be true, was wondering if anyone here purchased from these guys before or has a good recommendation.
http://www.amazon.com/Chevrolet-Cama...camaro+spolier |
09-18-2015, 07:28 PM | #2 |
Drives: 2015 1LS Red V6 Join Date: Aug 2015
Location: St Joseph, MO
Posts: 1,849
|
__________________
Sponsors:
Overkill Motorsport BCS Auto JacFab Machining APDEG Dream Gear Mobile Audio Thanks to Will @ Overkill Motorsports, Jason @ JacFab, Jim @ Ohio Speed, Brandon at Dream Gear, and the boys at Randy Curnow Chevrolet 5th Gen V6 Performance Facebook Group |
09-18-2015, 07:46 PM | #3 |
Drives: Black 2015 Camaro 2LS Join Date: Aug 2015
Location: houston
Posts: 96
|
Did you install it or pay someone?
|
09-18-2015, 10:05 PM | #4 |
|
Changing the spoiler is easy to do . There are videos on You tube you can watch to see how its done .
__________________
Mods, K&N CAI ,VTC , GM Perf Axleback Exhaust, Elite Eng CC and CSS, GM Strut Tower Brace,Carbon Fiber Anvil Spoiler,ASC T5 Splitter,Gen5diy Foglight kit.
|
09-18-2015, 10:43 PM | #5 |
ZYJ
Drives: 2017 1SS Camaro/6 speed Join Date: Sep 2014
Location: Miami, FL
Posts: 1,346
|
Easy.
Remove factory trunk "mat". Remove the 6 nuts tightening the factory spoiler. Pull the spoiler upward to take off the clip. Put weather strip, and an aluminum tape on the holes not used (it used 4 holes only). Install new screws. Take picture and smile. |
09-19-2015, 03:29 AM | #6 |
Drives: 2015 1LS Red V6 Join Date: Aug 2015
Location: St Joseph, MO
Posts: 1,849
|
Did mine on my own. Took about an hour
__________________
Sponsors:
Overkill Motorsport BCS Auto JacFab Machining APDEG Dream Gear Mobile Audio Thanks to Will @ Overkill Motorsports, Jason @ JacFab, Jim @ Ohio Speed, Brandon at Dream Gear, and the boys at Randy Curnow Chevrolet 5th Gen V6 Performance Facebook Group |
09-19-2015, 03:23 PM | #7 |
Drives: Black 2015 Camaro 2LS Join Date: Aug 2015
Location: houston
Posts: 96
|
The issue I have is I don't have a spoiler now so have to drill the holes. Need to find a good place to do it at so it wont rust through.
|
09-19-2015, 05:32 PM | #8 |
ZYJ
Drives: 2017 1SS Camaro/6 speed Join Date: Sep 2014
Location: Miami, FL
Posts: 1,346
|
|
09-21-2015, 09:14 AM | #9 |
Drives: 2015 Camaro LS, 2000 Firebird Join Date: Jun 2015
Location: Zionsville, Indiana
Posts: 21
|
I have it too. Nice fit. Easy to install. When you drill the holes. Start with a small drill bit first. Make sure templates don't move. Line them up before drilling final size. My templates moved on the left side. Was able to correct it because I used a smaller bit for the holes on the first shot. The directions will tell you to use WD-40 for a rust inhibitor. I used rustoleum primer to keep the rust away. Very nice product.
|
09-21-2015, 09:47 AM | #10 |
|
i have same spoiler but mine uses 6 bolts instead of 4 and cost more. i had to drill holes too and like posted above, use a small bit and then a larger one. mine also had weather stripping on the bottom of it already.
|
|
|
|
|