4 inches? - Page 2 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

TRC-SS · 09-20-2011, 02:45 PM

Quote:

Originally Posted by cipriank

I actually want them to sit inside and not sit inside the bezel....i can give it a shot

Just be VERY VERY careful if and when you do that, if the HOT exhaust tip is any where close to either touching or flowing on the ground effects it will heat up and bubble.....JUST LIKE MINE DID.....mine bubbled with the factory exhuast (not cut) sitting just inside the hole.....so if your going to do the tips inside....some part of the tip needs to just be inside the hole or it will be very hot in there

cipriank · 09-20-2011, 06:36 PM

Quote:

Originally Posted by TRC-SS

Just be VERY VERY careful if and when you do that, if the HOT exhaust tip is any where close to either touching or flowing on the ground effects it will heat up and bubble.....JUST LIKE MINE DID.....mine bubbled with the factory exhuast (not cut) sitting just inside the hole.....so if your going to do the tips inside....some part of the tip needs to just be inside the hole or it will be very hot in there

ok thank you ! will let you guys know how it went

jhmurphy · 09-20-2011, 06:52 PM

Here you go 4" tips on a Borla S series inside GFX.

cipriank · 09-21-2011, 07:51 AM

That looks sick!

jhmurphy · 09-21-2011, 04:51 PM

Thanks hope your install goes well.

austinjames · 09-21-2011, 05:04 PM

Quote:

Originally Posted by cipriank

can you fit a 4inch tip in the factory gfx kit? i dont want them to stick out...just inside the port

thats what she said

09-20-2011, 06:52 PM	#17
jhmurphy Drives: Grey Beast Join Date: Jul 2009 Location: Florida Posts: 591	Here you go 4" tips on a Borla S series inside GFX. Attached Images __________________ 2SS/RS A6 and some go faster parts

09-21-2011, 07:51 AM	#18
cipriank Drives: 2010 camaro 2ss Join Date: Feb 2011 Location: boca raton, fl Posts: 247	That looks sick! __________________ 2010 2ss L99 Mods: ADM race intake, ADM scoop w/ washer bottle, SLP long tube headers, SLP 25% UDP, SLP Loud Mouth 2 exhaust, Vmax TB, BER intake manifold,3.45 gears, MSD wires, SLP 160 t-stat, SLP Springs, EFI live tune by Redline Motorsports

09-21-2011, 04:51 PM	#19
jhmurphy Drives: Grey Beast Join Date: Jul 2009 Location: Florida Posts: 591	Thanks hope your install goes well. __________________ 2SS/RS A6 and some go faster parts

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
SS has 376 or 378 cubic inches?	DCSS	5th Gen Camaro SS LS LT General Discussions	93	10-12-2012 10:50 AM
FOUND PETITION TO GET RID OF FRONT PLATES	The_Beast_	USA - California	90	03-29-2012 12:54 AM
8 inches of snow in South Mississippi!	0235th	Off-topic Discussions	1	02-11-2010 03:36 PM
ls3 equal to or less than 410 cubic inches?	boostedyards86	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	18	12-10-2009 03:31 PM
2011 Camaro to be 2 inches shorter?	CJ Offshoredude	5th Gen Camaro SS LS LT General Discussions	18	07-12-2009 05:20 PM