02-23-2009, 01:31 AM | #1 |
hood problem
i have a problem with my 1991 RS camaro i thinks it has a 1969 RS hood becuase it dosen't want to close right and i can pick it up more than 55 mph or the hood starts to lift. so how can i fix this with out buying a new hood?
__________________
:5thgenvert:
|
|
02-23-2009, 09:20 AM | #2 | ||
Truth Enforcer
Drives: anything I can get my hands on Join Date: Sep 2006
Location: anywhere and everywhere
Posts: 22,797
|
um.... dont think that a 69 hood would fit on a 91.
but check the latch on the front as well as the spring on it. have someone pull the hood release cable as well to make sure its not binding.
__________________
Never race anything you can't afford to light on fire and push off a cliff
A group as a whole tends to be smarter than the smartest person in that group until one jackass convinces everyone otherwise. Quote:
Quote:
|
||
02-23-2009, 10:30 AM | #3 |
Drives: the 2nd amendment home Join Date: May 2008
Location: OK
Posts: 14,707
|
^ what he said. Yeah sounds like it's not even latching but hanging on the safety catch. Latch probably needs adjusted.
When you pop the hood, does it actually pop up half an inch or so?
__________________
"They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety."
-- Benjamin Franklin |
02-23-2009, 11:24 PM | #4 |
no i have to pull on the hood
__________________
:5thgenvert:
|
|
02-23-2009, 11:25 PM | #5 |
its like putting two male connections together
__________________
:5thgenvert:
|
|
02-24-2009, 04:38 PM | #6 |
The Krazzy bytch
|
Open the hood, Give the latch a spray of DW 40 & have someone pulling the latch cord from the inside.
Sounds like the hood is totally out of alingment. is there any gapping around the hood?
__________________
Heart breaks everyday when you cant take care of your family because you are unemployed, cant give your family what you want or what they need
I am not a man I have boobies. Cars are like women, If you treat her rough shes going to complain & you will hear about it. If you treat her right she will purrrrrrrrrrrrr Current cars owned , 72 Skylark vert,86 fiero GT Sold , 87 Iroc-z (sold), 90 Vette Vert SOLD , 95 Z28, 99 Silverado K1500 Totaled, 2010 CGM Camaro 2ss/rs (had to sell & I hate it ) ,2012 Cruze LT repoed. Current current list lol 2006 Silverado 2500hd. |
02-24-2009, 07:21 PM | #7 |
Drives: the 2nd amendment home Join Date: May 2008
Location: OK
Posts: 14,707
|
What irocz said...also, look at how the hood latches, lower male catch goes into the upper latch, mounted on the underside of the hood. Do they appear to be aligned when the hood is almost down? If so, try raising the lower catch. Loosen the set screw, raise it a couple of turns, and see if the hood catches when you close it. Remember how many turns you rotate it in case it doesn't help, you can set it back where it was.
It's hard to say what the prob is without looking at it in person.
__________________
"They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety."
-- Benjamin Franklin |
02-24-2009, 09:00 PM | #8 |
More human than human
|
use a marker on the screw and the piece it goes into so you can be acurate with how many turns .
__________________
1100 - 10/22/2008 3000 - 05/27/2009 3300 - 06/06/2009 3800 - 06/29/2009 4B00 - 06/29/2009 Warehouse 13 survivor Blood stains,speed kills,fast cars,cheap thrills,rich women,fine wine,i lost my sense i lost control i lost my mind. |
02-24-2009, 11:24 PM | #9 |
aka: The Evil Joker
Drives: 1991 Z28 (murdered out) Join Date: Feb 2009
Location: DFW
Posts: 32
|
Thirdgens are plagued with a bad hood design. It seems on 90% of them, you've got to shimmy the hood when opening.
X2 on the WD40
__________________
1991 Z28 305H.O. TPI T56 six speed w/ B&M ripper shifter, ROH Drift-Rs 18x9 w/265/35-18s & 18x10 w/295/35-18s, 4.10s, K&Ns, Holley 52mm, ADS Superchip, Hedman headers & Y-pipe, custom Flowmaster, MSD, SLP posi unit, Koni yellows, Eibach Pros, Lakewood boxed rear control arms, TDS wonderbar, Hotchkis dbl adj panhard bar |
03-09-2009, 08:51 PM | #10 |
Third gens aren't plagued with a bad hood design. The supports are worn and need replacing. That will help with the opening of the hood. If you think you have a 69 hood, then I can only assume that the hood is an aftermarket fiberglass hood. If that's the case, anything can be the issue.
__________________
|
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
1968 Nickey Camaro hood??? | 1968 Nickey | 1st & 2nd Generation Camaros | 6 | 03-19-2010 12:05 AM |
New Hood Idea, need photoshop experts!!! | ZZcamaro | Camaro Photoshops / Renderings Forum | 8 | 03-01-2009 07:34 PM |
ram air style hood? | tsg1391 | Cosmetics and Lighting Modification Discussions | 1 | 10-23-2008 04:43 PM |
Faux hood scoop..... | CamaroSpike23 | 5th Gen Camaro SS LS LT General Discussions | 5 | 10-13-2008 08:42 PM |
Problem with my v6 | TonytheTiger | 4th Generation Camaros | 12 | 08-22-2008 02:34 PM |