12-21-2013, 05:25 PM | #1 |
|
Shops local to So. Cal (Temecula) hex vents
Thinking of my next mod to be Hex vents. while i have tools thinking this is one of those times.. have someone else do it vs attempting it myself.
Any good shops? thanks in advance for suggestions! /bow
__________________
"The fact the GT500 can barely beat a $37k car with 200 less horsepower speaks volumes. There are about a million mods you can do to a LS3 to make a Camaro do the 1/4 faster then a GT500." (Vroom.)
Updated w/ Willow Springs: 1. Nissan GTR Track Pack 1:19.6 2. Ducati 1198 S 1:19.7 3. Nissan GTR 1:20.3 4. Corvette Z06 1:20.4 5. Audi R8 V10 Plus 1:22.0 6. Ferrari 458 Italia 1:22.3 7. CAMARO SS 1LE 1:22.7 8. Shelby GT 500 1:23.5 9. Mustang Gt Track Pack 1:25.8 |
12-22-2013, 11:44 PM | #2 |
Drives: summit white 2011 l99 ss/rs Join Date: Jan 2011
Location: 661
Posts: 201
|
do it yourself! i did, its ez. just watch the youtube video 20x and take your time. sayin that its scary as hell cuttin up your hood lol
|
12-22-2013, 11:54 PM | #3 |
Drives: 349 Stroker E85 Powered Miata Join Date: Dec 2013
Location: Venice Beach
Posts: 127
|
We could do that for you, but we are located in Venice, Ca if you wanna make the drive.
|
12-23-2013, 08:58 AM | #4 |
|
Thanks for the replies!! i'll consider it. if i make the trip to Venice i should also plan on the side fender vents.. (lol.. if your going to cut.. cut!)
thanks!
__________________
"The fact the GT500 can barely beat a $37k car with 200 less horsepower speaks volumes. There are about a million mods you can do to a LS3 to make a Camaro do the 1/4 faster then a GT500." (Vroom.)
Updated w/ Willow Springs: 1. Nissan GTR Track Pack 1:19.6 2. Ducati 1198 S 1:19.7 3. Nissan GTR 1:20.3 4. Corvette Z06 1:20.4 5. Audi R8 V10 Plus 1:22.0 6. Ferrari 458 Italia 1:22.3 7. CAMARO SS 1LE 1:22.7 8. Shelby GT 500 1:23.5 9. Mustang Gt Track Pack 1:25.8 |
12-24-2013, 01:04 PM | #5 |
Drives: My wife crazy with my C5 usage. Join Date: Apr 2009
Location: DFW
Posts: 6,558
|
I haven't found a shop in the area that I would trust that much. Faith took care of my car after it ate a Civic, but I'm not sure if they would attempt a "custom" project like the vents. Wouldn't hurt to ask though.
Sent from my iPhone using Tapatalk
__________________
UNDER CONSTRUCTION......again......
|
12-24-2013, 06:21 PM | #6 |
Drives: 349 Stroker E85 Powered Miata Join Date: Dec 2013
Location: Venice Beach
Posts: 127
|
We do frame sliders on bikes, just as nerve racking hard to measure it just right too since it goes from inside the fairing lol. Those vents won't be that bad they are square and flat just lots of measuring and taping off the paint and use a new blade. Becareful not to get the metal hot either or you can still mess up the paint from heat gotta take your time and go slow.
|
|
|
|
|