You are browsing camaro5 
 |
|
01-25-2010, 01:09 PM
|
#1 |
 
Drives: 2010 1SS CGM LS3 w/ blk rally Join Date: Jan 2010
Location: san diego, CA area
Posts: 258
|
Bowtie template
Does anyone have a template for the front and rear bowties. I need to fix the vinyl I put on my bowties, because apparently putting it on then cutting to size isn't going to work correctly for me.
|
|
|
|
05-26-2010, 10:33 AM
|
#2 |
     
Drives: White M6 1LT RS Join Date: Mar 2010
Location: Canton, MI
Posts: 1,676
|
Nobody??
__________________
Pfadt Sway Bars - FE3 Suspension - Barton Shifter - IdealG's Clutch Master Cylinder - Trifecta - Vmax TB - Vararam Intake - MACE 25mm Insulator - Plenum Insulator - Ported/Gasket Matched Intake Manifold - Rx Catchcan - AAC DRL's - 4 Pack Aux Gauges - Steering Controls - AAC Afterburners - DIY Led Sidemarkers - ZL1 Front End
Next mod: Done! |
|
|
|
|
06-20-2010, 12:53 PM
|
#3 |
 
Drives: 2010 Camaro 2SS/RS Join Date: Mar 2010
Location: Houston, TX
Posts: 487
|
bump?
__________________
2010 Camaro 2SS/RS
Imperial Blue | Grey two-tone Interior | Silver racing stripes | Magnaflow Comp Cat-back | CAI intake | Elite Engineering Tunnel Brace | Richmond (Houston), TX |
|
|
|
|
06-20-2010, 01:02 PM
|
#4 |
Drives: 2010 2SS/RS ; 1970 Firebird Formula Join Date: Jan 2010
Location: West Palm Beach
Posts: 1,252
|
Why not? It works for everyone else that has tried. I personally bought the precut ones first and ended up throwing them in the garbage. Just cut a piece larger than the bowtie and stretch it into place as necessary. there is a nice thread somewhere on here about how to do it.
|
|
|
|
|
06-20-2010, 03:19 PM
|
#5 |
|
Drives: 2010 Camaro 2SS/RS Join Date: Mar 2010
Location: Houston, TX
Posts: 487
|
Sweet... I am going to do that then. I just found some 3mil adhesive backed vinyl for $7.99. Two huge sheets of it.. Plenty of "do-overs" if needed! LOL!
__________________
2010 Camaro 2SS/RS
Imperial Blue | Grey two-tone Interior | Silver racing stripes | Magnaflow Comp Cat-back | CAI intake | Elite Engineering Tunnel Brace | Richmond (Houston), TX |
|
|
|
|
06-20-2010, 03:41 PM
|
#6 |
|
Drives: 2010 2SS/RS ; 1970 Firebird Formula Join Date: Jan 2010
Location: West Palm Beach
Posts: 1,252
|
That's the ticket. I went to a sighn store and got some scraps.
Good luck! Post some pix. |
|
|
|
|
06-20-2010, 07:54 PM
|
#7 |
Drives: 2010 Red SS/RS Join Date: Jul 2009
Location: Lake Jackson, TX
Posts: 476
|
I just did mine, and I'm going to redo it. It's not as easy as it looks. I had a small scrape with my fingernail and the Exacto knife jumped out of the groove several times. I'll be much more careful next time.
|
|
|
|
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Chevy Bowtie Colors | SamSS | Camaro Photos | Spyshots | Video | Media Gallery | 2 | 10-09-2009 08:46 PM |
| Billet Bowties from ChevyMall | Angelina | Cosmetics and Lighting Modification Discussions | 9 | 10-06-2009 11:04 AM |
| Bowtie Adhesive | AKcamaro | Cosmetics and Lighting Modification Discussions | 1 | 10-05-2009 09:53 PM |
| How is the rear bowtie attached? | VenomZ302 | Cosmetics and Lighting Modification Discussions | 4 | 07-10-2009 10:03 PM |
