11-09-2013, 03:16 PM | #1 |
Drives: 2013 ZL1 Join Date: Sep 2013
Location: Miami, FL
Posts: 63
|
speaker popping WITH ground loop isolator?
Hey guys, I recently installed an aftermarket amp (JL 700/5) with the FARK kit, AND used a ground loop isolator, and I'm still getting speaker pops when the radio turns off. I tried with the blacks leads both floating AND grounded, same issue. Any ideas? Anyone have this happen also?
|
11-10-2013, 09:00 PM | #2 |
Drives: 2011 Synergy Green Camaro LT Join Date: Jul 2011
Location: Lakeland, FL
Posts: 830
|
Yeah an isolator wont fix that. You either need a metra trigger or you can hook your remote wire to the cigarette + wire. Only down side is to the cigarette lighter is your key has to be turned for your radio to work. And the amp is always on when the car is on. Neither are really a big deal, just letting you know
|
11-11-2013, 11:02 AM | #3 |
Drives: 2018 1LE Join Date: Feb 2013
Location: delaware
Posts: 319
|
Ground loop ISO for speaker popping ????????? So with a jl amp it has a single sens. Switch. The amp will turn on and off with radio vol. if iwere you I would unhook the rem and try it that way if you deside to keep the rem I would use a pac tr-7 for the amp turn on
|
11-12-2013, 01:40 AM | #4 |
Drives: 2013 ZL1 Join Date: Sep 2013
Location: Miami, FL
Posts: 63
|
That's a good idea about unplugging the remote turn on. I'll give that a shot. Although in that case, wouldn't the amp be OFF all of the time?
And I only suggest the ground loop isolator as being the problem because according to ********, they recommend it when there is speaker pop. They say it would completely remove the pop, but in my case with it or without it, no difference. |
11-12-2013, 08:17 AM | #5 |
Drives: 2018 1LE Join Date: Feb 2013
Location: delaware
Posts: 319
|
ISO are used to take out winding sound from speakers they will not stop the amp from making the popping sound when it turns on or off. With the jl amp there is a switch on there for Signal sense witch will turn the amp on and off whit the vol of the radio.
|
11-13-2013, 02:29 AM | #6 |
Drives: 2013 ZL1 Join Date: Sep 2013
Location: Miami, FL
Posts: 63
|
I'm not sure about other series of JL amps, but for my XD there is no "signal-sense" turn-on. The amp only turns on when +12V is applied to the remote input. I tried disconnecting it, and as I suspected, the amp would not turn on, regardless of input volume. So this will not work. Other ideas?
|
11-13-2013, 10:04 AM | #7 |
Aural Assault Vehicle
Drives: 2010 IBM 2SS/RS, 2015 Sierra Denali Join Date: Jun 2011
Location: Garner, NC
Posts: 792
|
Check the thread in my signature below. Good luck fixing it.
__________________
My amplifier pop/click/thump solution thread
Power Mods * K&N Typhoon CAI, Flowmaster American Thunder cat-back exhaust, Hurst Short Throw Shifter Exterior Mods * Black Phantom Grille * 22" T.I.S. 537MS wheels w/ Nitto INVO rubber * OEM body kit Suspension Mods * BC Racing Coilovers * Lakewood Strut Tower Brace Audio Mods * Stinger SPP 2250 Battery * Mosconi 6to8v8 w/ RCD * Pioneer AVH-X7500BT * Scosche Dash Kit * 2 - Mosconi AS200.4 * 2 - JL Audio 13W6v2 * Focal 165KRX2 Power (active) * Mosconi Gladen One 240.2 * Rockford Fosgate Power T1692 |
11-13-2013, 05:31 PM | #8 |
Drives: 2018 1LE Join Date: Feb 2013
Location: delaware
Posts: 319
|
Really I was just playing around with a jl xd10005 it had signal sens on it and I think the xd 8008 has it as well. Any way you can go to the cig lighter or if I were you I would use a PAC tr-7
|
|
|
|
|