Installing a GM factory splitter for a 2014 ss/RS - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Sigelitest · 01-20-2015, 12:18 PM

I ordered a z/28 splitter and this is what they sent me. I liked it anyway and figured it would be easier to get up the driveway with this so I will show how the install went

Sigelitest · 01-20-2015, 12:30 PM

U can pick up a rivet gun at lowes for 20 bucks. Only use the holes toward the rear of the car the ones in the front are for riveting the splitter to the bracket later.

Sigelitest · 01-20-2015, 12:33 PM

After u have the front bracket mounted u can snap off the guide bars that are on the bracket.

Sigelitest · 01-20-2015, 12:35 PM

Bracket pics

Sigelitest · 01-20-2015, 12:37 PM

Time to mount and rivet side brackets

Sigelitest · 01-20-2015, 12:40 PM

Do not rivet the last hole toward the wheel well it will be secured from the inside through the splitter once it is installed

Sigelitest · 01-20-2015, 12:47 PM

Get the sides tucked in to the bracket

Sigelitest · 01-20-2015, 12:49 PM

Front and sides pushed into bracket

Sigelitest · 01-20-2015, 12:52 PM

I couldn't get the plastic rivets to hold well that attach the spoiler to the bumper cover so I used stainless bolts with lock washers

Sigelitest · 01-20-2015, 12:53 PM

Pic of plastic rivets

Sigelitest · 01-20-2015, 12:56 PM

There are holes in the bottom of the spoiler to access the place to drill to rivet the spoiler to the bracket.

Sigelitest · 01-20-2015, 01:01 PM

This spoiler is mounted using rivets and bolts there is no double stick tape at all and I have never seen anything mounted as secure before. I had an aftermarket one on my 11 and it fell off after a year. I don't see this ever coming off with out the bumper cover coming off first. Took about 45min to install. Had no instructions couldn't find any anywhere.

Sigelitest · 01-20-2015, 01:03 PM

Did this DIY in my cell phone so I will clean it up later on my laptop lol

hzisfrom1994 · 01-20-2015, 08:55 PM

What a rip off Z28 splitter...

01-20-2015, 12:18 PM	#1
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	Installing a GM factory splitter for a 2014 ss/RS I ordered a z/28 splitter and this is what they sent me. I liked it anyway and figured it would be easier to get up the driveway with this so I will show how the install went Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:30 PM	#2
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	U can pick up a rivet gun at lowes for 20 bucks. Only use the holes toward the rear of the car the ones in the front are for riveting the splitter to the bracket later. Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:33 PM	#3
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	After u have the front bracket mounted u can snap off the guide bars that are on the bracket. Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:35 PM	#4
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	Bracket pics Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:37 PM	#5
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	Time to mount and rivet side brackets Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:40 PM	#6
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	Do not rivet the last hole toward the wheel well it will be secured from the inside through the splitter once it is installed Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:47 PM	#7
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	Get the sides tucked in to the bracket Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:49 PM	#8
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	Front and sides pushed into bracket Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:52 PM	#9
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	I couldn't get the plastic rivets to hold well that attach the spoiler to the bumper cover so I used stainless bolts with lock washers Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:53 PM	#10
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	Pic of plastic rivets Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 12:56 PM	#11
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	There are holes in the bottom of the spoiler to access the place to drill to rivet the spoiler to the bracket. Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 01:01 PM	#12
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	This spoiler is mounted using rivets and bolts there is no double stick tape at all and I have never seen anything mounted as secure before. I had an aftermarket one on my 11 and it fell off after a year. I don't see this ever coming off with out the bumper cover coming off first. Took about 45min to install. Had no instructions couldn't find any anywhere. Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 01:03 PM	#13
Sigelitest Drives: White 2016 Z06 Join Date: Aug 2014 Location: Alabama Posts: 416	Did this DIY in my cell phone so I will clean it up later on my laptop lol Attached Images __________________ Hmmm now where did I put that screw

01-20-2015, 08:55 PM	#14
hzisfrom1994 ZYJ Drives: 2017 1SS Camaro/6 speed Join Date: Sep 2014 Location: Miami, FL Posts: 1,346	What a rip off Z28 splitter...