07-25-2010, 03:00 AM | #1 |
Drives: 11 Cruze Join Date: Jul 2009
Location: NY
Posts: 66
|
TVS 2300 Jackshaft vs Crank Pulley Change
deleted
Last edited by DNA; 03-06-2012 at 03:32 AM. |
07-25-2010, 07:08 AM | #2 |
Account Suspended
Drives: First 9 inch-12 bolt IRS Camaro Join Date: Jun 2009
Location: nc
Posts: 1,835
|
We like to overdrive the rear allowing us to keep a bigger front pully for better grip.If you have the funds for an 8 or 10 rib system that would be a plus...If you need any help give us a call and we would be glad to help
|
07-25-2010, 07:35 AM | #3 |
Drives: Maggie blown LS3 vette Join Date: Aug 2009
Location: SE TX
Posts: 1,490
|
Do you have the stock LS3 cam?
|
07-25-2010, 08:55 AM | #4 | |
Okie doke
|
Quote:
Can't speak to fuel ... I have been told where I am at with my BAP, that I am on the ragged edge near 6k .. do you know how your fuel is holding up where you are now? Crowley
__________________
|
|
07-25-2010, 03:59 PM | #5 |
Drives: 2010 Camaro SS/RS 427ci Join Date: Jul 2009
Location: Bowling Green, Ky
Posts: 3,355
|
This is exactly why I went with the 8 rib setup with the 10% overdrive as I can run a larger pulley and still get more boost. With the 8 rib and 10% overdrive I was running a 2.8 pulley and had no slip. It is money well invested and did I mention I have a set for sale that are just like new that replaces every pulley on the front of the engine over to 8 rib.....LOL
__________________
|
07-25-2010, 04:26 PM | #6 | |
Drives: Maggie blown LS3 vette Join Date: Aug 2009
Location: SE TX
Posts: 1,490
|
Quote:
|
|
07-25-2010, 09:20 PM | #7 |
Drives: 2010 Camaro SS/RS 427ci Join Date: Jul 2009
Location: Bowling Green, Ky
Posts: 3,355
|
I have experimented with every size pulley there is. Without the 8 rib setup, there was slippage with a 3.2 pulley. There is no harm with a 10% overdrive and is a lot easier and cheaper way to get more boost and use a larger jackshaft pulley. Of course doing a COG swap on the rear is an option but it is very expensive. When my car was at 750hp to the wheels, I spoke with Andy at ADM Performance about doing the COG and he turned me off of doing that and suggested I use more nitrous instead.
__________________
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DIY : Install underdrive pulley on 2010 Camaro SS | Nine Ball | Camaro DIY & HOW-TO instructions & discussions | 34 | 09-30-2013 08:25 PM |
FS: TVS 2300 3.0 pulley and belt | Supercharged SS | Forced Induction | 0 | 05-23-2010 06:47 PM |
ADM Performance 427 TVS 2300 | ADM PERFORMANCE | Forced Induction - V8 | 16 | 02-14-2010 03:57 PM |
does a SC pulley change require a different tune? | bilydean | Forced Induction - V8 | 4 | 02-04-2010 04:32 PM |
WHO WANTS A MAGGIE??? PACKAGE DEAL FOR THE TVS 2300 INSTALLED | east TX Muscle cars | USA - Texas | 10 | 06-11-2009 10:26 AM |