question about ARH LTs? - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Q8Y · 12-23-2009, 10:48 AM

I just finish installing ARH 1 7/8 LTs no cats on my camaro.after finishing the installation I noticed very little air is coming out where the pipes meets the factory pipes of the OEM muffler is this normal?I tighten the bolts as far as it goes but still very little air is coming out,one of the guys mentioned I should drive it for few days the carbon and other deposits will close these small gaps is this true?

alex33x · 12-23-2009, 10:53 AM

I dont know about the carbon deposits and such, but I do know that the metal will heat up as you drive and change shape, drive it around for a week or two then tigthen again.

Q8Y · 12-24-2009, 12:02 PM

I hope that's all it will take.thanks for your help

ZZcamaro · 12-26-2009, 03:11 PM

I would sya drive the car for a little while and make sure everything is good and hot....then tighten those clamps back up. i fyou have everything lined up correctly it will seal up with no problems.

12-23-2009, 10:48 AM	#1
Q8Y Drives: '12 F150 Join Date: Jun 2009 Location: KWT Posts: 132 View My Garage	question about ARH LTs? I just finish installing ARH 1 7/8 LTs no cats on my camaro.after finishing the installation I noticed very little air is coming out where the pipes meets the factory pipes of the OEM muffler is this normal?I tighten the bolts as far as it goes but still very little air is coming out,one of the guys mentioned I should drive it for few days the carbon and other deposits will close these small gaps is this true? __________________ recieved 7-10-09 2010 camaro black 2ss/RS/6m

12-23-2009, 10:53 AM	#2
alex33x Drives: 2013 Camaro ZL1 Join Date: Apr 2009 Location: El Paso, Tx Posts: 688	I dont know about the carbon deposits and such, but I do know that the metal will heat up as you drive and change shape, drive it around for a week or two then tigthen again. __________________ Devliered July 20, 2012

12-24-2009, 12:02 PM	#3
Q8Y Drives: '12 F150 Join Date: Jun 2009 Location: KWT Posts: 132 View My Garage	I hope that's all it will take.thanks for your help __________________ recieved 7-10-09 2010 camaro black 2ss/RS/6m

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Project “ZEUSS”	khislop007	Member Car Journals	129	10-09-2015 08:26 AM
ARH 1 3/4 or 1 7/8 cats or no cats??	Q8Y	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	27	10-30-2009 12:20 PM
Anyone have MBRP with ARH LTs?	caverman	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	1	10-13-2009 06:27 PM
Got my ARH LT's and Borla installed on my LS3	khislop007	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	10	10-08-2009 03:27 PM
Anyone have ARH LT's & SLP LM II's installed?	ssmike	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	10	09-01-2009 11:21 AM

12-26-2009, 03:11 PM	#4
ZZcamaro Drives: 2SS w/ ZZ427 Package!! Join Date: Oct 2008 Location: Pittsburgh, PA Posts: 2,700	I would sya drive the car for a little while and make sure everything is good and hot....then tighten those clamps back up. i fyou have everything lined up correctly it will seal up with no problems.