03-22-2017, 12:48 AM | #99 |
|
Just a update I haven't installed my n2mb yet but it looks like it's time to upgrade my fuel pump, even with me tuning the car I have maxed the stock pump and bap out, once I get all the parts in I will be making an access door vs dropping everything to install the new pump
__________________
Cai intake and a few other mods😎
|
05-25-2017, 10:45 PM | #100 |
Drives: 2010 2SS/RS L99 IBM silver stipes Join Date: Dec 2015
Location: K.C. Kansas
Posts: 1,329
|
Does it end there? Nice build. BTW, can you take a front picture s I can really see the flat black stripes? I have the same color car with silver stripes (that I hate), and am thinking about doing flat black. Thanks, and keep up the work..
__________________
2010 Imperial Blue w/ Silver stripes 2SS/RS L99
Mods = Not enough.... |
05-26-2017, 10:38 PM | #101 |
|
Sorry been busy dropping the tank to install a lme twin fuel pump(had to drop the tank for the cross over tube) and also the subframe for some new bmr subframe bushings I'll see if I have any good pictures
__________________
Cai intake and a few other mods😎
Last edited by Moreair1; 05-26-2017 at 10:53 PM. |
05-26-2017, 10:47 PM | #102 |
|
Didn't have a good front shot, all of them were in the shadows, but here is a picture from the rear
__________________
Cai intake and a few other mods😎
|
05-29-2017, 01:00 PM | #103 |
|
Bushing expierement, this is 15 minutes with a sawzall
__________________
Cai intake and a few other mods😎
|
05-29-2017, 10:57 PM | #104 |
|
If anyone does rear subframe bushings the blow torch is the way to go
__________________
Cai intake and a few other mods😎
|
05-30-2017, 10:35 AM | #105 |
I am not "Fast & Furious"
Drives: 2010 Camaro LSX454 1LE Join Date: Nov 2008
Location: Greeley Colorado
Posts: 1,040
|
Wow, that looks like a pain in the ass. Going to solid bushings?
__________________
The day I take a bend too fast
Judgement that could be my last I'll be wiped right off the slate Don't wait up 'cause I'll be late, I'll be late |
05-30-2017, 12:40 PM | #106 |
|
To be honest with the torch it's cake but all the other methods sucked, I'm just going with the bmr polys my car will probably never need the solids, the picture below isn't my car but shows the bushings I went with
__________________
Cai intake and a few other mods😎
Last edited by Moreair1; 06-08-2017 at 09:50 AM. |
06-05-2017, 12:37 PM | #107 |
|
Anyone looking at removing the rear craddle this jack worked awesome, balanced the assembly perfectly
__________________
Cai intake and a few other mods😎
|
06-09-2017, 10:03 PM | #108 |
|
Lpe fpcm vs stock
__________________
Cai intake and a few other mods😎
Last edited by Moreair1; 06-10-2017 at 09:35 PM. |
06-11-2017, 08:57 AM | #109 |
|
Fpcm mounted and rewired, should of been able to put everything back together today but someone had to order some replacement speakers
__________________
Cai intake and a few other mods😎
|
06-29-2017, 10:26 AM | #110 |
|
Next mod should be arriving today, a Flex fuel sensor
__________________
Cai intake and a few other mods😎
|
07-02-2017, 12:43 PM | #111 |
|
A link that I used to install my flex fuel sensor
http://www.camaro5.com/forums/showthread.php?t=497750
__________________
Cai intake and a few other mods😎
|
07-14-2017, 09:59 AM | #112 |
|
Well just a overall build update, i believe im down to installing my n2mb and rerouting the waste gate dump tubes , then as far as upgrades needed in the future will be, a new head unit with nav, and of course the major $$$$ items, a new monster clutch and a zl1 rear end, i'm still debating on the 3 inch exhaust, but other than cosmetic and maybe some further audio upgrades it should be about the end of my list.
__________________
Cai intake and a few other mods😎
|
|
|