02-07-2011, 02:03 PM | #1 |
How much boost with E-Force 3" pulley?
Does anyone know roughly how much boost the 3" pulley makes with the E-Force supercharger?
__________________
Edelbrock E-Force
Stainless Works Lts Roto Fab CAI Magnaflow Street Cat-Back DOD Delete Forgestar F-14's and Pedders XA + PKG Custom grind cam from Cincy Speed ADM dual fuel pump ADM AF/Boost gauges FTI 3200 convertor Hurst shifter Cincy Speed Build and Tune 540rwhp |
|
02-07-2011, 02:27 PM | #2 |
Se habla espaņol
Drives: 2010 Camaro SS/RS VR Join Date: Jun 2009
Location: Arizona/Sonora
Posts: 605
|
I was told this by stillen:
- LS3 TVS stock pulley 3.5" = ~7.5psi 599fwhp 547fwtq - L99 TVS stock pulley 3.875" = ~5.5psi 554fwhp 515fwtq - 3.25" TVS pulley = ~9.5psi (will require belt change) - 3.00" TVS pulley = ~11psi (recommended for forged internals) - 2.75" TVS pulley ~13-14psi (recommended for forged internals
__________________
2010 VR 2SS/RS
BMR Suspension Parts Hendrix HD Axles DSS Aluminum Shaft RPM Diff / 3.91 Gears LPE ZR1 Clutch Edelbrock E-Force SC / JRE Fuel Upgrade Livernois 1C cam 570 rwhp/559 rwtq SAE Best 1/4 time: 11.43 |
02-07-2011, 04:45 PM | #3 |
Drives: Maggie blown LS3 vette Join Date: Aug 2009
Location: SE TX
Posts: 1,490
|
3" pulley on a front drive TVS might be 10 to 12psi or it might be +14psi. Just depends on how the rest of the motor is set up. Need to know a little more on what's involved mod wise.
|
02-07-2011, 04:55 PM | #4 |
Will have a cam and currently has 1 7/8 lts. I want to keep the boost to a minimum. Like 8-9 at most. L99-Ls3 conversion if that matters.
__________________
Edelbrock E-Force
Stainless Works Lts Roto Fab CAI Magnaflow Street Cat-Back DOD Delete Forgestar F-14's and Pedders XA + PKG Custom grind cam from Cincy Speed ADM dual fuel pump ADM AF/Boost gauges FTI 3200 convertor Hurst shifter Cincy Speed Build and Tune 540rwhp |
|
02-07-2011, 05:22 PM | #5 |
Drives: Maggie blown LS3 vette Join Date: Aug 2009
Location: SE TX
Posts: 1,490
|
I'm running a front drive Maggie TVS with mild blower cam, Ported 243 heads (similar flow as stock LS3 heads), LT headers, 3" duals, no cats, and 3.1" pulley. I'm seeing 12psi. Based on that, I'd bet your LS3/L99 would see well over 8 to 9psi with the 3" pulley. If you're looking for 8 to 9psi, you might want to go a step bigger than the 3.0".
|
02-07-2011, 06:16 PM | #6 |
Se habla espaņol
Drives: 2010 Camaro SS/RS VR Join Date: Jun 2009
Location: Arizona/Sonora
Posts: 605
|
Im using the 3.25" and seeing around 8-9psi at WOT
__________________
2010 VR 2SS/RS
BMR Suspension Parts Hendrix HD Axles DSS Aluminum Shaft RPM Diff / 3.91 Gears LPE ZR1 Clutch Edelbrock E-Force SC / JRE Fuel Upgrade Livernois 1C cam 570 rwhp/559 rwtq SAE Best 1/4 time: 11.43 |
02-07-2011, 08:28 PM | #7 |
Drives: Something Fast Join Date: Feb 2010
Location: NC
Posts: 32
|
Depends on setup - cam, exhaust, heads, etc.
I have personally seen 3.25 pulley, cai & full exhaust get 8.5-9psi on hit & rise up to 11 by redline. 3.0 pulley on same set up peak at 13psi |
02-08-2011, 06:54 AM | #8 |
Drives: 2010 2SS/RS IBM Black Polished Join Date: Feb 2009
Location: Colorado
Posts: 2,108
|
Strongly suggest fuel delivery upgrades on anything smaller than 3.25 pully. JRE dual fuel rail upgrade and BAPon 3.25 pulley and LPE or ADM dual fuel pump 3.0. Also get inside and get internals done or you will be soon enough!
Rings, pistons, gaskets, bolts will all prove to be weak points.
__________________
418 Stroker, 621RWHP 648 lbs TORQUE Built by Laramie GM Auto Center Tuned by Nick at Mac Autosport. EForce SC, 2 3/4pulley,LPE dual fuel pump, JRE Twin fuel rail upgrade, posi clutch kit, RX oilcatch can and breather, Callies Compstar crankshaft and rods, Racing bearings, CP -13.8 race pistons, steel rings, Comp Cams X6 blower cam, Springs, HD timing chain and tensioner, Doug Thorley Tri Y LT headers, 89.7lb injectors, RPM rollbar, DSS1400 shafts, Simpson 5 pt harness, BMR Toe rods and trailing arms, led lights, RPM input and output shafts
|
02-08-2011, 08:06 AM | #9 |
Dual pump, JRE upgrade, injectors are all being done. I want the boost 8-9 psi max.
__________________
Edelbrock E-Force
Stainless Works Lts Roto Fab CAI Magnaflow Street Cat-Back DOD Delete Forgestar F-14's and Pedders XA + PKG Custom grind cam from Cincy Speed ADM dual fuel pump ADM AF/Boost gauges FTI 3200 convertor Hurst shifter Cincy Speed Build and Tune 540rwhp |
|
02-08-2011, 10:11 AM | #10 | |
Drives: 2SS Join Date: May 2009
Location: Fort Collins
Posts: 611
|
Quote:
__________________
2SS/RS CGM/BLK GFX MN6418 Stroker.785rwhp/885lbtq.50 SHOT NO2..Pfadt arms,toe links,coilovers,swaybars,end links,engine mounts,dif/sub bushings.MGWshifter.Tick LVL 3.ARH1 7/8 LT's/ARH exhaust.ADM gauges/race CAI.E-FORCE SC.8 rib IW 10%OD.LPE dual pump/module.85lb inj,custom valve covers.RMCR tune.TOOLEY RACING CAM.JRE posi kit.JRE fuel upgrade.RX MONSTER CatchCan.DSS axels/DS.Hammerhead rear, 3:73's. WYOSPEED builthttp://www.camaro5.com/forums/showthread.php?t=115687
|
|
02-10-2011, 11:02 PM | #11 |
Banned
Drives: Honda Join Date: Feb 2011
Location: USA
Posts: 4
|
E-Force 3"pulley will system Supercharger system to between 9.5 -10 PSI on car.
|
08-16-2013, 09:12 AM | #12 | |
Drives: 10 Camaro 2SS/RS, 70 Cuda, 71 Cuda Join Date: Jan 2010
Location: Oakley - Northern California
Posts: 1,156
|
Quote:
I am trying to decide which size pulley to go down too 3.0 or 3.25. I have a LS3 with modified heads, cam, injectors and exhaust but have not touched my bottom end. Have you rebuilt your bottom end or is it stock.? Current psi is 6.5 with stock edelbrock pulley.
__________________
"Z28 = first time I bought a new car just to strip parts for my current ride. GM needs to re-think restricted parts. "
|
|
08-16-2013, 02:06 PM | #13 |
Account Suspended
|
Just my opinion.... But I wouldnt go smaller than 3.25 on stock bottom end
You can see from my sig I did all the fuel upgrades before I went to a smaller pulley... during the dyno run as was stated...9.5 psi....and when the rpms approached the limiter...was just shy of 12 psi..... My next step is forged internals on stock displacement. Along with a JRE Cam Package and a 3" pulley. |
08-16-2013, 10:12 PM | #14 | |
Drives: 10 Camaro 2SS/RS, 70 Cuda, 71 Cuda Join Date: Jan 2010
Location: Oakley - Northern California
Posts: 1,156
|
Quote:
I appreciate the advice. On your change to a 3.25 pulley did you need to change your belt? it would seem on a ls3 the std pulley is 3.5 so a upgrade to 3.25 may not need it but knowing ahead of time would be great.
__________________
"Z28 = first time I bought a new car just to strip parts for my current ride. GM needs to re-think restricted parts. "
|
|
|
|
Thread Tools | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Supercharger / Turbocharger Results (INFO) Thread | radz28 | Forced Induction - V8 | 273 | 08-15-2023 04:44 PM |
DIY : Install underdrive pulley on 2010 Camaro SS | Nine Ball | Camaro DIY & HOW-TO instructions & discussions | 34 | 09-30-2013 08:25 PM |
Smaller blower pulley or bigger crank pulley? | B-rad | Forced Induction - V8 | 14 | 11-14-2010 12:09 AM |
Former task force head bullish on GM, Chrysler | ShnOmac | General Automotive + Other Cars Discussion | 0 | 10-21-2009 08:06 PM |
Took the SS to the track 126.67mph on boost only! | Icon Autosports | Forced Induction - V8 | 5 | 09-27-2009 11:15 AM |