06-07-2012, 02:55 PM | #365 |
HT5 EastSide
|
I didnt get the 4 inside bolts
maybe steve knew that I had the bolts with the insulator and thats all I need? No clue. |
06-07-2012, 04:31 PM | #366 | |
Drives: 2017 1SS 6spd Join Date: Jan 2011
Location: Utah
Posts: 2,869
|
Quote:
Anyway, my take on Steve's directions is to skip the stock "X-gasket" and just go with gasket maker. But I'm not sure and just expect to give it a good look, and figure it out when I get there. I'm thinking that the purpose of all these IM mods is to optimize flow (keep it laminar is the term I think engineers use) thru the IM, and that X-gasket looks like it would disrupt flow and increase resistance. I know most people have re-assembled with the gasket on top with good results, and when I get to that step, I may well do the same. |
|
06-07-2012, 04:35 PM | #367 | |
Drives: 2017 1SS 6spd Join Date: Jan 2011
Location: Utah
Posts: 2,869
|
Quote:
I got one of the very early 25mm spacers and just had 155mm bolts. I ordered new 160's to handle the additional 12mm of the plenum spacer. |
|
06-26-2012, 12:27 PM | #368 |
H-Town Camaro Club
Drives: 2010 Black Camaro 2LT RS M6 Join Date: Apr 2010
Location: Katy, TX
Posts: 926
|
Has anyone painted their plenum spacer? if so is there any specific paint you need to use?
__________________
|
06-26-2012, 06:20 PM | #369 |
Drives: LLT Machine Join Date: Nov 2011
Location: VIC/AUS
Posts: 563
|
|
06-27-2012, 08:12 AM | #370 | |
H-Town Camaro Club
Drives: 2010 Black Camaro 2LT RS M6 Join Date: Apr 2010
Location: Katy, TX
Posts: 926
|
Quote:
as a complete painting novice, what kind of prep would need to be done to the spacer in order to paint the outside edge?
__________________
|
|
06-27-2012, 09:25 AM | #371 | |
Drives: LLT Machine Join Date: Nov 2011
Location: VIC/AUS
Posts: 563
|
Quote:
Hope this helps If you have any more questions please don't hesitate to ask Kindest Regards, Steve |
|
06-27-2012, 12:20 PM | #372 |
H-Town Camaro Club
Drives: 2010 Black Camaro 2LT RS M6 Join Date: Apr 2010
Location: Katy, TX
Posts: 926
|
thanks for the info Steve.
__________________
|
06-27-2012, 05:50 PM | #373 |
Drives: 2017 1SS 6spd Join Date: Jan 2011
Location: Utah
Posts: 2,869
|
Shot a little VHT white and clear coat on this plenum spacer and blue on the IM...
Guess we'll see how it holds up! Just waiting for the gasket maker to set up and move to phase II. |
06-27-2012, 10:28 PM | #374 |
|
well i was going to get and do this, but with all the back and forth about bolts long,short, not fitting, not used,,,etc. to much redundant chat..maybe another time or day in the future when one simple post will clarify this for me, and maybe others. thanks ..later ryd..
|
07-02-2012, 02:03 AM | #375 | ||
Drives: LLT Machine Join Date: Nov 2011
Location: VIC/AUS
Posts: 563
|
No probs
Quote:
Quote:
If you have any questions please don't hesitate to ask Kindest Regards, Steve Last edited by MACE_ENG; 07-02-2012 at 02:23 AM. |
||
07-06-2012, 02:02 PM | #376 |
[COTW 4/13/15]
Drives: Supercharged LLT Join Date: Jul 2010
Location: Florida
Posts: 5,957
|
I was just wondering what these four do-dads are and used for thanks!
__________________
|
07-06-2012, 04:08 PM | #377 |
Drives: 2017 1SS 6spd Join Date: Jan 2011
Location: Utah
Posts: 2,869
|
Those are spacers. Place them under the plenum lid, to be held in place by the 4 center bolts. Use RTV on both sides to seal. They keep the bolts from distorting the lid when you tighten them down.
Don't let them fall into your IM when you're sliding in the bolts! A helpful tip is to use the lttle black plastic sleeves in the plenum lid holes to keep them centered until secure. |
07-06-2012, 04:45 PM | #378 |
[COTW 4/13/15]
Drives: Supercharged LLT Join Date: Jul 2010
Location: Florida
Posts: 5,957
|
Thanks ventmaster, unfortuently I think the spacer fell into the block, should I be concerned about it being tough to fish out? I'm really pissed at my self :(
Edit Nevermind I didn't, all is good in the world now lol
__________________
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Join TEAM LLT social group | RSokie | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 2849 | 02-10-2014 09:41 PM |
MACE 25mm Manifold spacer/ insulator to suit LLT | MACE_ENG | V6 Bolt-Ons & Tunes | 50 | 07-16-2012 12:39 AM |
Vmax Intake Manifold "BLACK ICE-olator" V6 LLT Base Test Results | Mike Norris | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 297 | 03-31-2012 07:41 PM |
Throttle Body Spacer on LLT | Nutbutt | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 19 | 11-14-2011 11:02 PM |