11-25-2009, 03:42 PM | #1 |
Drives: 2023 Sharkskin ZL1 M6 Join Date: Oct 2009
Location: Austin, TX
Posts: 122
|
Any good tips for getting a Jack under a Camaro?
Pics are better.
Basically, a "what to do" and "what not to do" would be good. I'd like to avoid putting jack or jackstands anywhere they might bend or unduly scar the car. Yeah, it's good to have good ramps (unlike my sliding rhinos that I'm scared to use) but advice on jacking sans ramps appreciated too. Any wisdom on the subject appreciated. |
11-25-2009, 03:52 PM | #2 |
The Mark of Excellence
Drives: 2010 ABM 1SS RS LS3 Join Date: Jan 2009
Location: Smallest State in the Union
Posts: 8,690
|
Drive up on some 2 X 10 s, this will raise the car up enough to get the jack underneath.
__________________
BMR, CAI, DynoMax, Elite Eng., Hurst, Jannetty, Clear Image Headers & Hi Flow cats, Jet Hot, LSR, TSW, VMax, Vredestein |
11-25-2009, 03:56 PM | #3 |
They make low profile car ramps, great for not scraping the front end. Make sure you get the hard plastic type, you can get them at any auto store
|
|
11-25-2009, 06:58 PM | #4 |
SoCal C5 Family Member
Drives: 2010 Camaro SS/RS - Black w/IOM; 6M Join Date: Jul 2009
Location: San Diego, CA, USA
Posts: 5,299
|
I can get my 1 1/2 ton jack under each side of the car to take the wheels off - there's a great spot behind the front wheels that the jack slips right into. I also have Race Ramps which are great! Just bought a 3 ton jack from Sears yesterday to get ready to do the Header install
Sorry, no pictures.
__________________
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~
2010 Black 2SS/RS; 6M; IOM, GFX, sunroof; ADM Race CAI; Zoomers CB; Viper Alarm; Pdaft F&R sways, Adj Endlinks, Rtrailing arms, Camber kit, strut brace, Front Trailing Arm Bushing; SLP Skip-Shift Elim; Tinted lights/windows; Hurst Short-throw; LoJack; Door & Dash ABL Mods; ********; JBA Shorty headers; AACStyle LEDs; Stillen DS rotors, Hawk Ceramic pads; Havoc Blk Chrome wheels: 20x9s; Lingenfelter Blk Al Pedals; RevXtreme Catch Can; Goodridge SS lines; Ported TB; RK Sport hood; Hotchkis chassis brace; KW V3 coilovers; |
11-28-2009, 07:13 PM | #5 |
Drives: 2023 Sharkskin ZL1 M6 Join Date: Oct 2009
Location: Austin, TX
Posts: 122
|
Where should jack stands be positioned to get all 4 corners up?
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New Camaro Exterior and Interior Stainless Steel Trim Parts from RPI Designs! | RPI Designs | Exterior Parts & Accessories | 30 | 02-20-2013 03:23 PM |
Pedders Suspension Benchmark Track Testing and New Jersey Track Day | Info@PeddersUSA.com | USA - NY / NJ / PA | 35 | 10-26-2009 05:20 PM |
Automobilemag.com: 2010 Chevrolet Camaro - Q&A | Scotsman | 5th Gen Camaro SS LS LT General Discussions | 23 | 10-12-2008 12:13 AM |