12-02-2012, 08:38 PM | #1 |
Might Have Screwed Up
I ordered My early Christmas presents Saturday and I hope I didn't screw up
I ordered 2 Boston Acoustic G2-12 Dual Voice Coil 12" Subs because I have had great success with them in another car. I ordered the box from ******** and I figured I might as well upgrade My existing sub amp since it is about 5 years old, came out of previous car. I ordered the Rockford Fosgate Punch P700-1bd figuring it is better to have more power than you need The woofers are rated at 300 watts RMS and a peak of 600 watts and are 2 ohms. This is where I may have screwed up? I was thinking 2 ohm speakers = 2 ohm load which would be putting 450 watts RMS to the woofers. That would be right in range. Now I just found out that with 2 woofers I will be a 1 ohm load and that jumps up the amp to 700 watts RMS and a maximum of 2500 watts Can I turn down the gains on the new amp or did I just screw up The subs are going in a sealed box because I like the tight chest pounding bass and listen to mainly mid 80's rock to present. Suggestions? Everything has already shipped Also, I see everybody using Dynamat through out the car in the trunk? Can I just Dynamat the inside of the sub box and secure it in the trunk?
__________________
2022 Black ZL1
RotoFab CAI, AWE Touring Edition Cat Back Exhaust. 665 Crank hp. est. and 660 Crank ft. lbs. est. Never been Dynoed |
|
12-02-2012, 09:25 PM | #2 |
|
If they are dual 2 ohm voice coils, then you can run the coils in series, making them 4 ohm. Then you run them in parrallel to the amp creating a 2 ohm load... You may have to still mess with the gains. 2ohm is more stable on amps than 1ohm. Your equipment will last longer.
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
__________________
CAI intake | OBX LT Headers | Flowmaster AT Exhaust | Trifecta Tune | SS Rear Diff, Axles & Driveshaft Zex 100 Shot Nitrous | Konig Airstrike Wheels | Custom Engine Cover, Fuse Box & Underhood Bowtie Eibach Springs & SS Sway Bars | BMR Strut Brace | Drake Shifter | Vitesse Paddles | 13.26 @ 105.88 mph |
12-02-2012, 09:37 PM | #3 |
What is OHMs law? Parallel would be different than 2 ohms right?
|
|
12-02-2012, 10:00 PM | #4 |
Nope, They are dual 4 ohm voice coils operating at 2 ohms and I cannot find anyway to wire two of them to where they end up a 2 ohm load?
The new Rockford Fosgate amp says: "The P700-1bd mono subwoofer amp dispenses 225 RMS watts at 4 ohms, or you can wire your subs for lower impedance to achieve higher power output — all the way up to 700 watts at 1 ohm."
__________________
2022 Black ZL1
RotoFab CAI, AWE Touring Edition Cat Back Exhaust. 665 Crank hp. est. and 660 Crank ft. lbs. est. Never been Dynoed |
|
12-02-2012, 11:11 PM | #5 |
Well the manual says: "The amplifier is 1-ohm stable (700 watts x 1) and will drive a pair of 4-ohm DVC subwoofers or quad-configuration of 2-ohm DVC subwoofers with ease."
My only concerns now are My 2 Woofer Wattage Specs: Specifications: Power Handling: Peak: 600 watts RMS: 300 watts Impedance: Dual 4 ohms RadialVent rigid cast aluminum chassis RadialVent cooling directs airflow around the voice coils for increased power handling Dual 4 Ohm Voice Coils 2-1/2" 4-Layer Voice Coils SureSet impedance selection provides simple impedance selection as well as overdrive protection 2" peak to peak excursion for devastatingly accurate, deep bass output from small sealed enclosures Rugged input terminals accept bare 8 gauge wire or pin connectors Integral sealing gaskets ensure tight seals for any mounting configuration Also I'm curious if anyone has ever put Dynamat inside a speaker box?
__________________
2022 Black ZL1
RotoFab CAI, AWE Touring Edition Cat Back Exhaust. 665 Crank hp. est. and 660 Crank ft. lbs. est. Never been Dynoed |
|
12-03-2012, 02:56 PM | #6 | |
Aural Assault Vehicle
Drives: 2010 IBM 2SS/RS, 2015 Sierra Denali Join Date: Jun 2011
Location: Garner, NC
Posts: 792
|
Quote:
In short, you should be just fine.
__________________
My amplifier pop/click/thump solution thread
Power Mods * K&N Typhoon CAI, Flowmaster American Thunder cat-back exhaust, Hurst Short Throw Shifter Exterior Mods * Black Phantom Grille * 22" T.I.S. 537MS wheels w/ Nitto INVO rubber * OEM body kit Suspension Mods * BC Racing Coilovers * Lakewood Strut Tower Brace Audio Mods * Stinger SPP 2250 Battery * Mosconi 6to8v8 w/ RCD * Pioneer AVH-X7500BT * Scosche Dash Kit * 2 - Mosconi AS200.4 * 2 - JL Audio 13W6v2 * Focal 165KRX2 Power (active) * Mosconi Gladen One 240.2 * Rockford Fosgate Power T1692 |
|
12-03-2012, 04:24 PM | #7 |
Ok, Thanks
I guess I should have ordered the 1000watt then .... lol
__________________
2022 Black ZL1
RotoFab CAI, AWE Touring Edition Cat Back Exhaust. 665 Crank hp. est. and 660 Crank ft. lbs. est. Never been Dynoed |
|
12-03-2012, 04:29 PM | #8 |
Car nut
Drives: Tahoe Z71, Race cars Join Date: Aug 2010
Location: Las Vegas, NV
Posts: 671
|
If they are dual 4ohm, than you can wire it to mono 4ohm or 1ohm.
You'll be ok just turning down the gain some, just be aware of overdriving them or distortion/clipping as that will burn the voicecoils faster than anything else.
__________________
Quote: Don't you just hate it when Satan steals your ride and does all these weird ass mods to it?
R.I.P. Evan .. A true Friend |
|
|
|
|