let the pictures do the talking [COTW 7/22/13]

[bandier]

Duuuude.... You got a BIG ONE!

[I call it Vera]

That's insane. Can't wait to see more details on the insanity.

[james347]

[KLR ZL1]

Freaking awesome man, can't wait to see and hear more. Would really love to see in person but that would never happen.

[ayousef]

Okay im sure um gonna miss more than a few details of this car but here goes:

- We begin with an RHS 427 block, built by LME using custom diamond pistons, ceramic coated tops and antifriction coated skirts. Billet Oliver rods, and Callies Dragonslayer crankshaft

- Mast 305cc LS7 12degree heads, the best LS heads money can buy. Fitted with PAC 1521 dual springs (awesome springs FYI), 1.7 rockers with trunion upgrade, and Stainless steel intake and exhaust valve (hollow intake stem).

- Whipple 4.0 obviously, sand rail kit which is why its HUGE cause it has a huge intercooler that it sits over. Custom CNC'ed dual induction airbridge, believe it or not this is most likely the most expensive single part on the car.

- Dual ported 87mm throttle bodies, and dual 4" cold air intakes routed to the brake duct openings

- Meth kit with hardline meth tubes, as shown in the images.

- Aeromotive Eliminator fuel pump with fuel pump speed controller, regulator, hardlined fuel feed and fuel rails.

- ID1000 injectors

- American racing headers 2" long tube headers, 3" merge collectors + x-pipe

- B&B fusion exhaust full 3" exhaust including butterfly valves. Custom switch to gain full control of butterfly valve operation.

- Hendrix Engineering RPS triple disk clutch, rated at 1200rwtq

- Fully built RPM transmissions TR6060

- Ron Davis custom radiator utilizing stock fans because the stock fans are awesome.

- HUGE KDi intercooler heatexchanger

- Meziere 20gpm intercooler pump + custom intercooler reservoir tank (despite the biased opinion from Lingenfelter the pump works flawlessly)

- Custom clutch fluid reservoir separated from brake reservoir

- Pfadt ZL-spec sway bars

- Dual DBW throttle body controller

- Hptuners 2.5bar OS

- MGW short throw shifter

- Custom camshaft from Flowtech Induction

- Custom MPD1 cowl hood, awesome quality and built using a special high distortion temp resin in effort to avoid any fiberglass deformation due to excessive engine or ambient heat.

Im sure I missed a lot of stuff no kidding.

Brakes are getting upgraded, rear seats removed, lightweight battery, slight additional suspension/chassis mods, 18inch wheels + proper tire setup, carbon fiber front fenders, and hood redone in carbon fiber (possibly), plus a custom tubular front crash support since we removed the factory one which blocks a big deal of airflow to the intercooler/radiator.

EDIT: forgot about the driveshaft shop carbon fiber driveshaft.

[KaotiK]

wow! i'm impressed!

[Vangres]

Way to go!

[All-American ZL1]

It won't matter with all that horsepower, but could you post the weight of the car when you get done? Just curious Thanks

[ayousef]

Originally Posted by All-American ZL1

It won't matter with all that horsepower, but could you post the weight of the car when you get done? Just curious Thanks

I agree that it wont matter but I wouldn't like it to be too heavy which is why im giving it a diet.

This was more or less an open budget build and at one stage I was going to slap twin turbos on the rear, yes im crazy

Not a lot of cars that could make this much torque and 1000rwhp and still run on straight 93 octane.

Next time I do something stupid it will be a 440ci motor with a Whipple 5.0 and race gas

PS. I purposely kept a few things a secret until I show it to you in a video.

[ayousef]

dont have anything too interesting but here goes

[tmandoug1]

Very impressive!

[big dave]

That's disgusting!! What would I do with an open budget???

[Eric-MPD1.com]

UNREAL! Bet you cant wait to get behind the wheel!

[Baltimorejohn1]

Nice